Home Styles 88 5531 942 User manual

Part List
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools required for assembly: Phillips screwdriver
(Knock-Down Construction, please refer to
the last pageof instructions for steps to
complete drawer assembly)
For assembly see instructions in carton 88 5531 941, 88 5531 943
Hardware List
Tools recommended for assembly: Level
B.
Bottom
1 pc.
D.
Back Panel
1 pc.
F.
Shelf
6 pcs.
C.
Plinth
2 pcs.
E.
Back Panel
1 pc.
G.
Drawer
6 pcs.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
M4x20
Machine Screw
20 pcs.
Cam Lock Screw
48 pcs.(+1 extra)
Cam Lock
48 pcs.(+6 extra)
Flat Washer
6 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
for Drawer Side Part
40 pcs. (+1 extra)
Adjustable Pin
24 pcs. (+1 extra)
Spring Washer
6 pcs. (+1 extra)
M6x35
Bolt
6 pcs. (+1 extra)
M3.5x16
Wood Screw (short)
for Drawer Base Part
30 pcs. (+1 extra)
88 5531 942
Storage Island
Knob
for Drawer N
8 pcs.
Knob
for Drawer G
12 pcs.

Assembly Instructions 2/8
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
*You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Put Cam Lock Screws into
the pre-drilled holes of Top (A),
Plinths (C),Side Panels (H),(I)
and Middle Panel (J) and tighten.
(see Figure 1)
Cam Lock Screw
C
A
J
H
Cam Lock Screw
Figure 1
Cam Lock Screw
Cam Lock Screw
C
I

Assembly Instructions 3/8
Figure 3
STEP 3
Attach Back Panel (D) to unit
with Cam Locks, Flat Washers,
Spring Washers and Bolts.
(see Figure 3)
Spring Washer
Flat Washer
Bolt
STEP 2
Attach Bottom (B) to Side Panel (H) using Cam Locks.
(see Figure 2)
Figure 2
Figure 3
Cam Lock
Cam Lock D
B
H

Assembly Instructions 4/8
STEP 5
Attach Front Rails (L) to unit
using Cam Locks.
Attach Back Panel (E) to unit with
Cam Locks, Flat Washers, Spring
Washers and Bolts.
K
L
J
E
LL
L
KK
K
STEP 4
Attach Front Rails (K) to unit using
Cam Locks.
Attach Middle Panel (J) to unit with
Cam Locks, Flat Washers, Spring
Washers and Bolts.
Spring Washer
Flat Washer
Bolt
Cam Lock
Spring Washer
Flat Washer
Bolt
Cam Lock

Assembly Instructions 5/8
STEP 7
Attach Plinths (C) to unit
with Cam Locks.
Attach Leg Support (M) to unit.
STEP 6
Attach Side Panel (I) to unit
with Cam Locks.
M
I
C
C
Cam Lock
Cam Lock

Assembly Instructions 6/8
Figure 4
STEP 8
Attach Top (A) to unit with
Cam Locks.
STEP 9
Insert Adjustable Pins into side panels
and middle panel at desired level, then
place shelves (F) into position.
STEP 10
Slide Drawers (N) and (G) into position.
To level the unit, adjust the adjustable levelers
on the bottom of unit. (see Figure 4)
Note: Unit must be level to
work properly.
Cam Lock
Adjustable Pin
G
G
G
A
N
G
G
G
N
F
N
N
F
F
F
F
F

(Figure 3)
STEP 3
Insert wood screws (6X)short
into the pre-drilled holes in G5,
tighten screws. (See Figure 3)
STEP 4
Attach hardware pulls
with machine screws.
(See Figure 4)
STEP 2
Slide G5 into the grooves in G3
and G4. Be sure to push G5 all
the way forward so it meets G1.
(See Figure 2)
Tighten all screws used in drawer assembly.
(Figure 1)
(Figure 2)
MAKE SURE ROLLER
IS ON THE BACK
G2
G3
G4
G5
G1
Drawer G
Part List
(Figure 4)
STEP1
Attach G1 to G3 and G4, using
a andPhillips screwdriver
wood screws (4X),long
tighten halfway.
Attach G2 to G3 and G4 using
wood screws (4X),long
tighten halfway. (See Figure 1)
G3
G4
G1
G2
G1
G3
G4
G5
G2
G1.
Front Part
6 pcs.
G5.
Base Part
6 pcs.
G2.
Back Part
6 pcs.
G3.
Side Part
6 pcs.
G4.
Side Part
6 pcs.
Assembly Instructions 7/8

(Figure 3)
STEP 3
Insert wood screws (6X)short
into the pre-drilled holes in N5,
tighten screws. (See Figure 3)
STEP 4
Attach hardware pulls
with machine screws.
(See Figure 4)
STEP 2
Slide N5 into the grooves in N3
and N4. Be sure to push N5 all
the way forward so it meets N1.
(See Figure 2)
Tighten all screws used in drawer assembly.
(Figure 1)
(Figure 2)
MAKE SURE ROLLER
IS ON THE BACK
N2
N3
N4
N5
N1
Drawer N
Part List
(Figure 4)
STEP1
Attach N1 to N3 and N4, using
a andPhillips screwdriver
wood screws (4X),long
tighten halfway.
Attach N2 to N3 and N4 using
wood screws (4X),long
tighten halfway. (See Figure 1)
N3
N4
N1
N2
N1
N3
N4
N5
N2
N1.
Front Part
4 pcs.
N5.
Base Part
4 pcs.
N2.
Back Part
4 pcs.
N3.
Side Part
4 pcs.
N4.
Side Part
4 pcs.
Assembly Instructions 8/8