Home Styles 6803-20 User manual

Table Hardware List
Table Part List
6803-20
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Bistro Set
A.
Top
1 pc.
B.
Side
2 pcs.
C.
Panel
2 pcs.
D.
Glass Top
1 pc.
Hex Wrench
1 pc.
Flat Washer
12 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
M6x15
Head Cap Bolt (short)
12 pcs. (+1 extra)

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Panels (C) to Side (B) with
Head Cap Bolts (short) and Flat Washers,
tightening bolts only halfway.
(See Figure 1)
STEP 2
Attach Side (B) to unit with Head Cap Bolts (short)
and Flat Washers, tightening bolts only halfway.
Flat Washer
Head Cap Bolt (short)
Figure 1
C
C
B
Head Cap Bolt (short)
Flat Washer
B

Assembly Instructions 3/6
STEP 4
Turn unit over to its upright position.
Place Glass Top (D) onto unit.
STEP 3
Place Top (A) upside down on a soft cloth.
Attach unit to Top (A) with Head Cap Bolts (short)
and Flat Washers, tightening bolts only halfway.
(See Figure 2)
Tighten all bolts used in Steps 1, 2 and 3.
Head Cap Bolt (short)
Flat Washer
A
Figure 2
D

Chair Hardware List
Chair Part List
F.
Side
1 pc.
E.
Seat
1 pc.
G.
Side
1 pc.
H.
Back
1 pc.
I.
Cushion
1 pc.
M6x40
Head Cap Bolt (long)
5 pcs. (+1 extra)
M6x30
Head Cap Bolt
4 pcs. (+1 extra)
Flat Washer
9 pcs. (+1 extra)
Assembly Instructions /46

Assembly Instructions /56
STEP 6
Attach (E) to unit withSeat
Head Cap Bolts (long) and Flat Washers,
tightening bolts only halfway.
(See Figure 4)
Head Cap Bolt
Flat Washer
Head Cap Bolt (long)
Flat Washer
Figure 3
H
STEP 5
Attach ides (F) and (G) to Back (H)S
with Head Cap Bolts and Flat Washers,
tightening bolts only halfway.
(See Figure 3)
E
Figure 4
G
F

Assembly Instructions /66
STEP 8
Turn unit to its upright position.
Place Cushion (I) into position.
I
Flat Washer
Head Cap Bolt
STEP 7
Head Cap Bolts and Flat WashersInsert
into unit, tightening bolts only halfway.
Tighten all bolts used in Steps 5, 6 and 7.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460