Homebase ANDORRA 2 SEATER SWING SET User manual

INSTRUCTION MANUAL
IMPORTANT: Please read these instructions before using the product and retain for future use.
HHGL Limited, MK9 1BA; HHGL (ROI) Limited, D02 X576
H159 x W117 x D156.5cm
ANDORRA 2 SEATER
SWING SET

Domestic use only.
Maximum user weight is 110kg per seat.
We recommend that you cover your garden furniture when it's not in use and that it is stored in a garage or
shed throughout the winter months. Please ensure the furniture is dry before storing.
IMPORTANT INFORMATION
Regularly check all the bolts, screws and fastenings are secure.
Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
This product should not be discarded with household waste. Take it to your local authority waste disposal centre.
Keep children and animals away from the work area; small parts could pose a choking hazard if swallowed.
Do not stand or put weight on the component parts or the product, as this could cause damage.
We do not recommend the use of power drills/drivers for inserting screws, as this could
Check you have all the components listed on page 3.

1
2
3
4
5
8
11
6
7
10
9
COMPONENTS - FITTINGS
Please check you have all fttings listed below. If you have any missing or damaged fittings, please contact your
local store.
Note: The quantities below are the correct amount to complete the assembly. In some cases, more fittings may
be supplied than required.
A
B
C
D
E
H
F
G
J
I
x 6
x 36
x 8
x 4
x 4
x 2
x 4
x 1
x 2
x 1 x 1
x 1
x 2
x 1
x 2
x 1
x 2
x 4
x 1
x 2
x 14
x 4
K
x 1
COMPONENTS
Please check you have all components listed below. If you have any missing or damaged components, please
contact your local store.
Top cross beam
Front upright support
Rear upright support
x 2
Lateral cross brace
Rear cross brace
Swing arm tube
Swing right arm
Swing left arm
Arm connecting tube
Seat assembly
Canopy
Suspension spring
Plastic screws
L
M
M6 x 75mm Bolts
M6 x 45mm Bolts
M6 x 35mm Bolts
M6 x 40mm Bolts
D16 Washers
ST4.2*16mm Screws
M6 x Metal nuts
10mm Nut wrench
4mm Allen key
Leg caps
Canopy/frame connector

NOTE: When fastening with nuts and bolts, always use a washer (E) between the tube and the bolt or
the tube and the nut.
Step 1
Fasten the front and rear upright supports (2 and 3) at the top by using bolts (A), washers (E) and metal
nuts (G). Repeat the same procedure for both sides. Keep the bolts loose. At both ends, insert the
assembled upright supports (2 and 3) into the top cross beam (1).
Step 2
Fasten the lateral cross braces (4) to the upright supports (2 and 3) by using bolts (B), washers (E) and
metal nuts (G). Repeat the same procedure for both sides. Fasten the rear cross brace (5) to the rear
upright supports (3) by using bolts (B), washers (E) and metal nuts (G). Insert the leg caps (K) into all of
the base feet. Tighten all of the nuts and bolts.
2
3
AE
G
A
E
G
EE
2
3
1
2
4
5
3
K
K
B
E
E
G

Step 3
Insert the arm connecting tube (9) to the swing arm (7 and 8).
Step 4
Fasten the arm connecting tube (9) to the seat assembly (10) by using bolts (C), washers (E) and metal
nuts (G). Repeat the same procedure for both sides.
7
8
9
10
Step 4
Fasten a swing arm tube (6) and a swing arm (7) to the seat back by using bolt (D), washers (E) and metal
nuts (G). Repeat the same procedure for both sides. Fasten another swing arm tube (6) to the swing arm
(8) at the front bend by using bolt (D), washers (E) and metal nuts (G). Repeat the same procedure for
both sides.
C
E
E
G
6
E
D
G
E
E
D
G
E

Step 5
Hook the suspension springs (H) into the top of both swing arm tubes (6). Do the same procedure for both
sides. Hang the opposite ends of the suspension springs (H) into the holes located on the angled braces of
the top cross beam (1). Repeat the same procedure for both sides.
Warning:
Make sure that both ends of the suspension springs (H) go completely through the holes on the top cross
beam (1) and the swing arm tubes (6).
H
6
Step
J) into the canopy (11). Fasten them together by using screws (F) in
J).
Warning:
11
F
J
I
the pre-drilled holes. Make sure that the teeth of the canopy/frame connectors are facing towards the
inside of the frame. Attach and fasten the Canopy assembly onto the adjustable teeth on top of the
cross beam (1) with plastic screws (I) to each side of the canopy/frame connectors (J).
ASSEMBLY COMPLETE