Homebase MATARA TEA FOR TWO User manual

Powder-coated steel frame
Hand woven synthetic rattan
Toughened glass table top
Chairs:H69 x W65 x D66cm
Table: H45 x W45 x D45cm
MATARA
TEA FOR TWO
INSTRUCTION MANUAL
IMPORTANT: Please read these instructions before using the product and retain for future use.
HHGL Limited, MK9 1BA HHGL (ROI) Limited, D02 X576

2
SAFETY AND CARE ADVICE
IMPORTANT INFORMATION
Please read these instructions fully before starting assembly.
• Check that you have all the components and appropriate tools listed in this booklet before starting
assembly.
• Remove all fittings from their plastic bags and separate them into their groups.
• Keep children and animals away from the work area; small parts could choke if swallowed.
• Make sure you have enough space to lay out the parts before starting.
• Do not stand or put weight on the component parts during assembly as this could cause damage.
• Assemble on a soft, level surface, to avoid damaging the unit or your floor.
• Two-person assembly is recommended.
• Dispose of all packaging materials carefully and responsibly.
• Assemble the item as close to its final position as possible.
• From time to time, check there are no loose screws on this unit.
• This product should not be discarded with household waste.
• Please note: The cushions are not weatherproof and should be stored indoors if not used.
• This product is made from toughened glass, which is strong but not unbreakable. In the unlikely
event that the glass fails, it will break into a large number of small fragments that may be spread over
a wide area. This is a feature of toughened glass and is designed to remove the risk of injury from
glass breaking into large shards.
• If the glass is chipped or broken, stop using the product.
• Tables should not be dragged at any time.
• Do not strike the glass with hard or pointed items, or place heavy weight on the table.
• Do not place hot items directly onto the glass.
• Avoid dropping objects on the glass, as this may weaken or shatter it.
• Do not use the glass as a chopping surface.
• We do not recommend the use of power drills/drivers for inserting screws, as this could
damage the unit. Only use hand screwdrivers.
• Regularly check all the bolts, screws and fastenings are secure.
• Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
• Make sure each screw matches the corresponding figure, to ensure correct assembly.
• This product should not be discarded with household waste. Take to your local authority waste
disposal centre.
• To prolong the life of this unit, we recommend it is stored inside during winter or extended periods
of bad weather.

3
A1
Backrest
Table rim
Table leg 1
Table leg 2
Left armrest
Right armrest
Seat
A2
A3
2
2
2
A4
B1
B2
B3
2
1
2
2
Please check you have all components listed below. If you have any missing or damaged components,
please contact your local store.
COMPONENTS - PANELS
B5
Table glass
Seat cushion
C
D
1
2
2
Back cushion
Bottom
B4 1

R u le r - U s e th is ru le r to h e lp co rre ctly ide n tify th e s cre ws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
4
Screw
COMPONENTS - FITTINGS
Please check you have all fittings listed below. If you have any missing or damaged fittings, please
contact your local store.
Note: The quantities below are the correct amount to complete the assembly. In some cases, more
fittings may be supplied than required.
E
F
G
H
28
M6x20
Screw M6x35
12
40
40
Washer
Screw cap
Allen key
Tools included
I1

5
A2
G
EGA4
A2
A1
H
E
G
A4
ASSEMBLY INSTRUCTIONS - CHAIR
Step 1
Use screws Eand washers Gto fix the seat A4 with left armrest A2. Do not fully tighten all screws until assembly is completed.
Step 2
Use screws Eand washers Gto fix the backrest A1 onto the unit. Do not fully tighten all screws until assembly is completed.
x4
x4

Step 3
Now your sofa Is ready to use.
Step 4
ASSEMBLY COMPLETE
Put seat cushion Cand back cushion Donto the chair.
Use screws E and washers Gto fix the right armrest A3 onto the unit. Do not fully tighten all screws until assembly is completed.
A2
A4
A3
C
D
H
E
G
6
x6

7
ASSEMBLY INSTRUCTIONS - COFFEE TABLE
Step 5
Use screws F and washers Gto fix the table legs1 B2 onto the table rim B1. Do not fully tighten all screws until assembly is
completed.
Step 6
Use screws F and washers Gto fix the table legs2 B3 onto the table rim B1. Do not fully tighten all screws until assembly is
completed.
B2
B1
H
F
G
x2
B3
B1
B3
H
F
G
x2
B2

GH F
8
B4
Step 7
Use screws Fand washers Gto fix the bottom B4 onto the unit. Do not fully tighten all screws until assembly is
completed.
Step 8
Carefully place the glass B5 onto the table rim. Now your table is ready to use.
B5
x4
ASSEMBLY COMPLETE