Honeywell DT8016MF4 DUAL TEC User manual

DT8016MF4 / DT8016MF5 DUAL TEC®Motion Sensor – Installation Instructions
QUICK LINKS
Mounting Location Guidelines
Open the Sensor
Mount the Sensor
Sensor Components and Settings
Wire the Sensor
Wiring Examples
Walk Test the Sensor
Detection Patterns
Remote LED Enable
Relay Operation
Troubleshooting
Sensor Specifications
Accessories
Approval Listings
Mounting location guidelines:
•The maximum range is obtained at a mounting height
of 2.3m (7’ 6”).
•Allow a clear line-of-sight to all areas to protect.
•Do not directly face windows.
•Avoid close proximity to moving machinery, fluorescent lights, and
heating/cooling sources.
•Not for use in applications with pets.
1. Turn the arrow to point to the Unlock symbol.
2. Press firmly on housing latch.
3. Gently separate the front and rear housing.
[EN] = approved installation.

- 2 -
See wiring
details and
examples on
page 3.

- 3 -
WIRING DETAILS
-Observe proper polarity.
-If not using the integrated EOL resistors, set all switches to
OFF.
-If using the integrated EOL resistors:
1.Connect the sensor to the panel (see wiring diagrams
below).
2.Set the appropriate tamper [RT], alarm [RA] and trouble [RF]
DIP switches to ON (see Step 4 on page 2).
Notes:
-Consult the Control Panel manual to determine
proper EOL selection.
-The Alarm, Tamper and Trouble EOL settings must
each only have one switch ON.
-The EOL values should be set at the same time.
Wiring Examples
Alarm, Tamper and
Trouble configured
to one loop.
Alarm, Tamper and
Trouble configured
to two loops.
1. Close the sensor and apply power to the sensor. Initialization is
complete when the LED stops flashing slowly (about 30 seconds).
2. Walk through the detection area and observe the LED.
3. Adjust the microwave range as necessary to meet installation requirements.
Walk test mode is active for 10 minutes, then automatically exits test mode,
disables the LED and enters normal operation mode. For an additional 10
minute walk test, enable walk test mode again with the flashlight feature (see the
following page).
RA = Alarm EOL resistor
RF = Trouble EOL resistor
RT = Tamper EOL resistor
W1 = 1 and 2 loop connection resistor.
Notes:
-During power up and walk test
modes the LED is active
regardless of the LED
Enable/Disable DIP switch setting.
-When the microwave sensitivity is
set to minimum, the sensor range
is reduced to 5m.
LED Power Up
Walk Test
[10 min.]
Normal Fault
Red
Slow
Blink
ON
Alarm
ON
Alarm
Fast
Blink
Yellow OFF
ON
Microwave OFF OFF
Green OFF ON
PIR OFF OFF

- 4 -
Flashlight Feature:
1. Use a flashlight with a bright light beam, and stand within 1.2 m (4’) of the
sensor.
2. Swing the light beam past the sensor IR window 3-5 times, holding the beam
on the window for 0.5 second each pass.
The flashlight feature is only available for the first 24 hours after the first power up.
REMOTE LED ENABLE (LED INPUT)
The LED input terminal allows the LED to be
remotely enabled. To use this feature, the
LED DIP switch (switch 2) must be OFF,
allowing the LED to operate based on the voltage level
connected to the LED Input (see Wiring Details).
Switch 2
LED Input
LED Operation
OFF
High ( +12 V)
Enabled
OFF
Low (0 V)
Disabled
ON
Low (0 V) or High (+12 V)
Enabled
RELAY OPERATION
SENSOR STATUS
Normal
Intrusion
Trouble1
Alarm Relay
Closed
Open
Closed
Trouble Relay 2
Closed Closed Open
1 For information on Trouble conditions, see the Troubleshooting section.
2 In a Trouble condition, the Trouble relay will latch open until the Trouble
condition has been cleared.
TROUBLESHOOTING
TROUBLE*
NORMAL
Low Voltage1
Self-Test
Failure
2
Alarm Relay
Closed
Closed
Closed
Trouble Relay
Closed
Open
Open
Red LED
Off
Off
Flashing
Yellow LED
Off
Off
Off
*TROUBLE CONDITIONS:
1Low Voltage: The sensor is disabled. [Note: If voltage drops below 5V, both
Alarm and Trouble relays open.]
2Self-Test Failure conditions:
•Microwave supervision failure: The sensor is operating in PIR mode only.
•PIR self-test failure: The sensor is disabled.
•Temperature compensation failure: The temperature compensation is
disabled.
Depending on the Trouble condition, take the following corrective actions:
•Verify the power supply is sufficient (at least 9V at the sensor).
•Cycle power to the sensor.
•Walk test the sensor.
If the Trouble condition does not clear, replace the sensor.
Zones
A
2
Look-down
B
12
Lower
C
10
Intermediate
D
36
Long

- 5 -
SPECIFICATIONS
Range: 16 m x 22 m
Power: 9.0 - 15 VDC; 9 mA typical, 14 mA maximum, 12 VDC;
AC Ripple: 3 V peak-to-peak at nominal 12 VDC
Alarm Relay: Energized Form A; 30 mA, 25 VDC, 22 Ohms
resistance maximum. Alarm Relay Duration: 3 seconds
Trouble Relay: Energized Form B; (NC) 30 mA, 25 VDC; 22 Ohms
resistance maximum
Tampers: Cover; (NC with cover installed) Form A;
30 mA, 25 VDC; Magnetic Field
Microwave Frequencies: DT8016MF4 - 10.525 GHz
DT8016MF5 - 10.587 GHz
RFI Immunity: 15 V/m, 80 MHz – 2.7 GHz
PIR White Light Immunity:10,000 Lux typical
Fluorescent light filter: 50 Hz / 60 Hz.
Operating Temperature:-10° to 55° C
Relative Humidity: 5 to 95%; non-condensing
Temperature Compensation: Advanced Dual Slope
Dimensions: 11.6 cm H x 7.0 cm W x 4.3 cm D
Weight: 135 g / 5 oz (net weight)
ACCESSORIES
SMB-10
(P/N 0-000-110-01) Swivel Mount Bracket
SMB-10C
(P/N 0-000-111-01) Swivel Mount Ceiling Bracket
SMB-10T
(P/N 0-000-155-01) Swivel Mount Bracket w/Tamper
Note : The accessories are not covered by certifications.
APPROVAL LISTINGS
EN50131-2-4:2008, Security Grade 2,
Environmental Class II.
Suitable for connection to an EN 60950 Class
II Limited Power Source.
Note: In EN 50131-2-4 compliant installations, mount the sensor at 2.3m,
enable look down, set the microwave sensitivity to maximum and lock
the sensor housing with the cover lock (see “[EN]” where noted in
Steps 1-4).
IMPORTANT: The sensor should be tested at least once each year.
NF&A2P 2 boucliers (référentiel NF324-H58) et
conforme aux normes EN50131-2-4 et
RTC50131-2-4; IP30 IK04
DT8016MF4 – N° de certificat: 2821420017
DT8016MF5 – N° de certificat: 2821420018
Organisme de certification:
CNPP Cert. : www.cnpp.com et
AFNOR Cert.: www.marque-nf.com
Honeywell Security Group - BP1219
1198 avenue du docteur Maurice Donat
Sophia Antipolis
06254 Mougins Cedex.
TEL: [phone]
FAX: [phone]
DT8016MF4
INCERT B-893-0014
DT8016MF5
PD6662:2010
LARMKLASS 2
Corrente norminale: 12 =
Corrente massima
assorbita: 14 mA

For any additional information, please refer to our Website:
http://www.honeywell.com/security/emea/hscdownload
Or contact:
Honeywell Security Group
Newhouse Industrial Estate
Motherwell
Lanarkshire ML1 5SB
United Kingdom
Please contact your local authorised Honeywell representative for product warranty information.
2013 Honeywell International Inc. Honeywell and DUAL TEC are registered trademarks of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved.
P/N 800-15839 Rev A
www.honeywell.com/security
Tel: [phone]
Email: [e-mail]