Honeywell SNG-Q Series User manual

Installation Instructions for the
Quadrature Speed and Direction Sensors
SNG-Q Series
32309314
Issue C
Sensing and Internet of Things
General Information
Honeywell’s SNG-Q Series Quadrature Speed and Direction
Sensors are designed to provide both speed and direction
information. Speed information is provided from digital square
wave outputs; direction is provided using a quadrature output
with signals 90° phase shifted from each other. With the
quadrature output, target direction is determined by output
lead/lag phase shifting.
The product is designed for applications where enhanced
accuracy is required to detect small target features. This
accuracy is enabled by dual differential Hall-effect sensor IC
technology. The SNG-Q Series is designed for a wide operating
temperature range, robust electrical noise immunity and
industry leading environmental sealing capability.
This product includes an O-ring seal for pressure applications,
and a fixed mounting flange for simple installation using one
fastener.
Table 1. Electrical Specifications
Characteristic Parameter Comment
Supply voltage 4.5 V to 26 V —
Output signal:
type
duty cycle1
phase shift
high
low:
SNG-QPLA/QPCA/
QPMB/QPDB
load current
rise time
fall time
frequency
square wave
50% ±10%
90° ±45°
>Vs - 0.5 V
<0.5 V
<1.75 V
40 mA max.
10 us max.
5 us max.
3 Hz to 20 kHz
Two channel, phase shifted by 90° either channel, may lead or lag.
Dependent on target geometry and sensor-to-target orientation; see Figures 2, 3, 4,
5, 6, 7, 8, 9 for recommended orientation.
Dependent on target geometry and sensor-to-target orientation; see Figures 2, 3, 4,
5, 6, 7, 8, 9 for recommended orientation.
—
—
Applies to each output at all conditions.
1 kOhm pull-up resistor, dependent on load resistor.
1 kOhm pull-up resistor, dependent on load resistor.
Frequencies >10 kHz may be dependent on target geometry and air gap.
Short circuit protection 50 mA max. —
Supply current:
normal
max.
12 mA
18 mA
all conditions
Reverse voltage -26 V max. 10 min duration
1Duty cycle = Time high/time total.

2 Sensing and Internet of Things
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
Table 3. Environmental Specifications
Characteristic Condition Parameter
EMI:
radiated immunity
bulk current injection
ESD
ISO 11452-2, 400 MHz to 1 GHz
ISO 11452-4, 1 MHz to 400 MHz
ISO 10605, Section 9 conforms to CE Mark standards
EN60947-5-2:2007 and EN 60947-5-2/A1:2012
100 V/m
100 mA
±8 kV contact, ±15 kV air
Operating temperature — -40°C to 150°C [-40°F to 302°F]
Thermal shock, air to air -40°C to 150°C [-40°F to 302°F], 60 min. soak, <3 s transfer 500 cycles
Humidity 95% humidity at 38 °C [100 °F] 240 hr
Salt fog 5% salt solution by mass at 35 °C [95 °F] 96 hr
Thermal saline dunk 100°C to 25°C [212°F to 77°F] air to liquid, 5% saline 10 cycles
High temperature expo-
sure with power 150°C [302°F], 13.5 Vdc, 1 kOhm load 500 hr
Vibration 3 perpendicular axes, 48 hr per axis 29.28 GMS, 50 Hz to 2000 Hz
MIL-STD-202-214
Degree of protection — IP69K
Resistance to fluids —general under-the-hood automotive fluids
NS
Table 2. Mechanical Specifications
Characteristic Parameter
Sensing air gap 0,0 mm to 2,0 mm [0.0 in to 0.08 in]
Target:
width1
slot width2
tooth width2
tooth height3
>5,0 mm [0.20 in] recommended; 12,7 mm [0.5 in] typ.
2,0 mm [0.08 in] min.
2,0 mm [0.08 in] min.
>3,0 mm [0.12 in] recommended; 5,0 mm [0.20 in] typ.
Materials:
housing
bushing
O-ring
cable4
PBT
brass
fluorocarbon with PTFE coating, ø11,8 mm [ø0.47 in] OD x ø1,80 mm [ø0.07 in] CS
EVA, four conductor, 36 AWG, 28 strand, ø5,2 mm [ø0.20 in] jacket
Mounting:
bore size5
torque
ø15,15 mm to ø15,40 mm [ø0.60 in to ø0.61 in]
10 N m [88.5 in-lb] max. with M6 X 1.0 bolt
1Narrower targets may limit axial offsets.
2Other geometry may be suitable.
3Shorter tooth heights may limit maximum air gap performance.
4Applies to SNG-QPLA-001, SNG-QPCA-001, SNG-QPMB-000, SNG-QPDB-000, and SNG-QPDB-002.
5Application dependent.

Sensing and Internet of Things 3
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
Figure 3. SNG-QPLA-000 Mounting Dimensions (For reference only: mm/[in].)
Vs: Yellow wire
Ground: Black wire
Channel A: White wire
Channel B: Blue wire
SNG-QPLA-000
Load A
Load B
Power
Supply
(4.5 V to 26 V)
Circuit Diagram
Note: The load resistor values should be such
that the output current does not exceed the
maximum load current of 40 mA.
Use Ohm's Law to calculate the load resistor
based on the supply/load voltage used:
R = V / 0.04 A
Figure 1. Sensor Output (All catalog listings) Figure 2. Possible Mounting Orientations
Tooth
Slot
Output
channel A
(leading)
Output
channel B
(lagging)
Phase shift
T
arget cross section
rel
ative to output
channel
A
Vsupply
Vsupply
90°
0° 0°
180° 270° 360°
Radial
Axial
ø6,20
[0.24]
ø13,00
[0.51]
ø21,00
[0.83]
21,5
[0.85]
500
[19.69]
15,0
[0.59]
15,0
[0.59]
5,00
[0.20]
34,95
[1.38]
2,50
[0.10]
4,50
[0.18]
56.0 Max.
[2.20]
8,50 - 9,00
[0.33 - 0.35]
23
[0.91]
4
[0.1
6]
ø13,90
[0.55]
ø14,95
[0.59]
2,0
[0.08]
Leadwire Assignment
Yellow Black White Blue
Vsupply Ground Channel A Channel B

4 Sensing and Internet of Things
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
Figure 4. SNG-QPCA-001 Mounting Dimensions (For reference only: mm/[in].)
Circuit Diagram
Vs: Pin 1
Ground: Pin 2
Channel A: Pin 3
Channel B: Pin 4
SNG-QPCA-001
Load A
Load B
Power
Supply
(4.5 V to 26 V)
1
23
4Deutsch DTM04-4P Pinout
(mating connector is Deutsch DTM06-4S)
Pin 1 Pin 2 Pin 3 Pin 4
Vsupply Ground Channel A Channel B
ø6,20
[0.24]
ø13,00
[0.51]
ø21,00
[0.83]
21,5
[0.85]
1250
[49.2]
15,0
[0.59]
15,0
[0.59]
5,00
[0.20]
34,95
[1.38]
2,50
[0.10]
4,50
[0.18]
56.0 Max.
[2.20]
8,50 - 9,00
[0.33 - 0.35]
ø13,90
[0.55]
ø14,95
[0.59]
2,0
[0.08]
Note: The load resistor values should be such
that the output current does not exceed the
maximum load current of 40 mA.
Use Ohm's Law to calculate the load resistor
based on the supply/load voltage used:
R = V / 0.04 A

Sensing and Internet of Things 5
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
Figure 5. SNG-QPRA-000 Mounting Dimensions (For reference only: mm/[in].)
Vs: Pin D
Ground: Pin A
Channel A: Pin B
Channel B: Pin C
SNG-QPRA-000
Load A
Load B
Power
Supply
(4.5 V to 26 V)
Circuit Diagram
Amp Superseal 1.5 Connector Pinout
(mating connector is Amp Superseal 1.5 282088)
Pin A Pin B Pin C Pin D
Ground Channel A Channel B Vsupply
31,77
[1.25]
5,85
[0.23]
66,0 Max.
[2.60]
5,00
[0.20]
2,50
[0.10]
4,50
[0.18]
34,95
[1.38
]
8,50 - 9,00
[0.33 - 0.35]
ø6,20
[0.24]
15
[0.59]
3
[0.12]
13,80
[0.54]
108.5°
ø13,90
[0.55]
ø14,95
[0.59]
2,0
[0.08]
Note: The load resistor values should be such
that the output current does not exceed the
maximum load current of 40 mA.
Use Ohm's Law to calculate the load resistor
based on the supply/load voltage used:
R = V / 0.04 A

6 Sensing and Internet of Things
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
Figure 7. SNG-QPMB-000 Mounting Dimensions (For reference only: mm/[in].)
Circuit Diagram
Vs: Yellow wire
Ground: Black wire
Channel A: White wire
Channel B: Blue wire
SNG-QPMB-000
Load A
Load B
Power
Supply
(4.5 V to 26 V)
Leadwire Assignment
Yellow Black White Blue
Vsupply Ground Channel A Channel B
ø13,00
[0.51]
ø6,2
[0.24]
ø
18,0
[0.71]
15,0
[0.59]
ø20,8
[0.82]
8,50 - 9,50
[0.33 - 0.37]
44,95
[1
.77]
2,5
[0.10]
5,0
[0.20]
4,50
[0.18]
ø13,9
[0.55]
ø14,9
[0.59]
23
[0.91]
61,0 Max.
[2.40]
490
[19.29]
4
[0.16]
0,0 - 2,0
[0.0 - 0.8]
Note: The load resistor values should be such
that the output current does not exceed the
maximum load current of 40 mA.
Use Ohm's Law to calculate the load resistor
based on the supply/load voltage used:
R = V / 0.04 A

Sensing and Internet of Things 7
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
Figure 8. SNG-QPDB-000 Mounting Dimensions (For reference only: mm/[in].)
VS: Pin 1
Ground: Pin 4
Channel A: Pin 3
Channel B: Pin 2
SNG-QPDB-000
Load A
Load B
Power
Supply
(4.5 V to 26 V)
Circuit Diagram
Amp Superseal 1.5 282106 Pinout
(mating connector is Amp Superseal 1.5 282088)
Pin 1 Pin 2 Pin 3 Pin 4
Vsupply Channel B Channel A Ground
0,0 - 2,0
[0.0 - 0.8]
ø13,90
[0.55]
ø14,95
[0.59]
8,50 - 9,50
[0.33 - 0.37]
44,95
[1
.77]
145
[5.71]
61,0 Max.
[2.40] 2,5
[0.10]
5,0
[0.20]
4,50
[0.18]
50.0
[1.97]
ø 13,00
[0.51]
ø 6,2
[0.24]
ø
18,0
[0.71]
15,0
[0.59]
ø 20,80
[0.82]
Pin 4
Pin 3
Pin 2
Pin 1
Note: The load resistor values should be such
that the output current does not exceed the
maximum load current of 40 mA.
Use Ohm's Law to calculate the load resistor
based on the supply/load voltage used:
R = V / 0.04 A

8 Sensing and Internet of Things
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
Figure 7. SNG-QPDB-002 Mounting Dimensions (For reference only: mm/[in].)
Note: The load resistor values should be such that
the output current does not exceed the maximum
load current of 40 mA.
Use Ohm's Law to calculate the load resistor based
on the supply/load voltage used:
R = V / 0.04 A
Circuit Diagram
Deutsch DTM04-4P Pinout
(mating connector is Deutsch DTM06-4S)
Pin 1 Pin 2 Pin 3 Pin 4
Vsupply Channel B Channel A Ground
0,0 - 2,0
[0.0 - 0.8]
ø13,90
[0.55]
ø14,90
[0.59]
61,0 Max.
[2.40]
44,95
[1
.77]
2,5
[0.10]
5,0
[0.20]
4,50
[0.18]
1250
[49.2]
41,30
[1.63]
ø13,00
[0.51]
ø6,2
[0.24]
ø18,0
[0.71]
15,0
[0.59]
8,50 - 9,50
[0.33 - 0.37]
Vs: Pin 1
Ground: Pin 4
Channel A: Pin 3
Channel B: Pin 2
SNG-QPDB-002
Load A
Load B
Power
Supply
(4.5 V to 26 V)

32309314-C-EN | C | 05/17
© 2017 Honeywell International Inc.
Quadrature Speed and Direction Sensors
SNG-Q Series
Issue C
32309314
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free
of defective materials and faulty workmanship during the
applicable warranty period. Honeywell’s standard product
warranty applies unless agreed to otherwise by Honeywell
in writing; please refer to your order acknowledgement or
consult your local sales office for specific warranty details.
If warranted goods are returned to Honeywell during the
period of coverage, Honeywell will repair or replace, at its
option, without charge those items that Honeywell, in its sole
discretion, finds defective. The foregoing is buyer’s sole
remedy and is in lieu of all other warranties, expressed or
implied, including those of merchantability and fitness for
a particular purpose. In no event shall Honeywell be liable
for consequential, special, or indirect damages.
While Honeywell may provide application assistance
personally, through our literature and the Honeywell web site, it
is buyer’s sole responsibility to determine the suitability of the
product in the application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this writing.
However, Honeywell assumes no responsibility for its use.
E-mail: [e-mail]
Internet: sensing.honeywell.com
Phone and Fax:
USA/Canada [phone]
International [phone]; [phone] Fax
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Honeywell Sensing and Internet of Things
9680 Old Bailes Road
Fort Mill, SC 29707
www.honeywell.com

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Honeywell:
SNG-QPDB-002 SNG-QPMB-000 SNG-QPDB-000