Honeywell ScanDome ll HTX-3000 User manual

ScanDome ll™KEYBOARD CONTROLLER
`
Please read this manual thoroughly before use and keep it handy for future reference.
Rev.2 04/10/05
Instruction Manual
HTX-3000
HTX-3000

2
WARNING AND CAUTION
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instruction in the literature
WARNING
CAUTION
accompanying the product.

3
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO
PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE
REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN
THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE
INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL
AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE
USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN
EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY
THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME
NMB-003 DU CANADA.
WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER
MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.

4
IMPORTANT SAFEGUARDS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that product heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for
long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE
RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING
OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
15. Use Certified/Listed Class 2 power supply transformer only.
16. Warranty does not cover the product damages caused by installation
carelessness or natural disaster such as lighting.

5
Table of Contents
Chapter 1.0 INTRODUCTION
1.1 Features ---------------------------------------------------------------------- 6
1.2 Unpacking ---------------------------------------------------------------------- 7
Chapter 2.0 INSTALLATION
2.1 Connection Diagram --------------------------------------------------------- 8
2.2 Termination & Dip Switch Setting ---------------------------------------- 12
2.3 Keyboard Setup -------------------------------------------------------------- 13
2.4 Master & Slave Keyboard Setting --------------------------------------- 15
Chapter 3.0 OPERATION
3.1 Keyboard Lock/Unlock ----------------------------------------------------- 16
3.2 Controlling Multiplexer ----------------------------------------------------- 16
3.3 Summary of Keyboard Control ------------------------------------------ 18
Appendix A Trouble Shooting ------------------------------------------------- 21
Appendix B SPECIFICATION ------------------------------------------------- 22

6
Chapter 1
INTRODUCITON
1.1 Features
This keyboard controller is capable to control 32 ScanDomeII™dome cameras and remote control
functions for variety of external switching devices like Multiplexer(max 255) etc…
The keyboard controller features:
•The capability of control a camera’s panning and tilting movement with variable speed from 0.5 °/sec
to 90°/sec as well as its zoom, focus, and iris command. Normal speed is inversely proportional to
the current zoom ratio. Turbo speed is Max 380°/sec when Ctrl key pressed.
•The ability to define and recall up to 240 presets, which are immediate camera call-ups of preset
position view, with automatic zoom and focus.
•The ability to define and run up to 8 patterns, which comprise a sequential series of pan, tilt, zoom,
and focus movements from a single camera.
•The ability to define and run up to 8 scans, which scan between two limits.
•The capability to incorporate up to 300 of the presets, patterns, scan and tour itself in up to 8 tours,
where the presets, patterns and scan automatically displayed one after the other on the Main monitor.
•Global preset recalls preset of all dome cameras.
•Auto Iris mode activated by moving the joystick slightly.
•Auto Focus mode is activated by twisting the zoom handle slightly.
•Programmable user preferences (alarm, preset, title, etc.).
•Administrator and user, two levels of password are supported for higher security.
•One Master and slave Keyboard is supported to control in a distant place.
•Multiplexers (Max 255) can be controlled remotely.
•Up to two programmed data from domes can be downloaded to none volatile memory space in KBD,
and uploads to a new dome.
Slave Keyboard
<Flashing Light>
UP TO 32 CAMERA J-box
J-box
Master Keyboard
UP TO 255 MULTIPLEXER
<Sensor>
<Siren>
UP TO 4
Output
Alarm
UP TO 8
Alarm Input
Figure 1 – Typical system Configuration

7
1.2 Unpacking
Unpack the equipment and make sure all listed items are included in the box.
Contents of Keyboard box
Keyboard controller ------------------------------- 1
Junction box --------------------------------------- 1
3m cable -------------------------------------------- 2
M4 Self tapping screws ------------------------- 4
Instruction manual --------------------------------- 1
12VDC SMPS & Power Cord ------------------- 1

8
Chapter 2
INSTALLATION
2.1 Connection Diagram
2.1.1 Basic Installation Diagram
3~4
5~8
1~2
1~4
ALARM OUTPUT
UP TO 4
ALARM OUTPUT ALARM OUTPUT
ALARM INPUT
HALF DUPLEX MODE : TX+,TX-
RS-485
ALARM INPUT
UP TO 8
ALARM INPUT
LIGHT
SIREN
SENSOR
DOME1 +
DOME1 -
AWG # 24
BNC
BNC
MONITOR
AC 24V
POWER
RX-(TX-)
RX+(TX+)
(RX-)
(RX+)
(RS-422)
RS-485
GND
(RX+)
AC-
AC+
FGND
(RX-)
AC-
RX+(TX+)
RX-(TX-)
AC+
NC2
NO2
NC1
NO1
COM2
COM1
AL4
GND
AL3
AL2
GND
AL1
NO4
NC4
COM4
NO3
NC3
COM3
GND
AL8
AL7
GND
AL6
AL5
AC 24V
POWER
RS-422
SIMPLEX MODE : TX+,TX-
DUPLEX MODE : TX+,TX-,RX+,RX-
Figure 2 – Basic installation diagram

9
2.1.2 Single Multiplexer
RS-485(-) PIN No.5
RS-485(+) PIN No.4
POWER
AC 24V
AL5
AL6
GND
AL7
AL8
GND
COM3
NC3
NO3
COM4
NC4
NO4
AL1
GND
AL2
AL3
GND
AL4
COM1
COM2
NO1
NC1
NO2
NC2
AC+
RX-(TX-)
RX+(TX+)
AC-
(RX-)
FGND
AC+
AC-
(RX+)
GND
RS-485
(RS-422)
(RX+)
(RX-)
RX+(TX+)
RX-(TX-)
AC 24V
POWERPOWER
AC 24V
BNC
MULTIPLEXER
SPOT MONITOR MAIN MONITOR
BNC
BNC
AWG # 24
Figure 3 – Single Multiplexer

10
2.1.3 Single User with Two Multiplexer
RS-485(+) PIN No.4
RS-485(-) PIN No.5
BNC
SPOT MONITOR 2ND MAIN MONITOR
2ND MULTIPLEXER
AWG # 24
BNC
BNC
1ST MAIN MONITOR
1ST MULTIPLEXER
BNC
AC 24V
POWER POWER
AC 24V
RX-(TX-)
RX+(TX+)
(RX-)
(RX+)
(RS-422)
RS-485
GND
(RX+)
AC-
AC+
FGND
(RX-)
AC-
RX+(TX+)
RX-(TX-)
AC+
NC2
NO2
NC1
NO1
COM2
COM1
AL4
GND
AL3
AL2
GND
AL1
NO4
NC4
COM4
NO3
NC3
COM3
GND
AL8
AL7
GND
AL6
AL5
AC 24V
POWER
Figure 4 – Two Multiplexer
Spot output of the first multiplexer to be
connected to 16th input of the second
multiplexer.
And first spot output of the 2nd multiplexer to
be connected to the spot monitor. You will see
the picture of the selected camera (1~31) on
spot monitor by selecti
ng camera
No.
+
Cam
.

11
2.1.4 Two Multiplexer with Slave Keyboard Controller
SPOT MONITORSPOT MONITOR
RS-485(-) PIN No.5
RS-485(+) PIN No.4
BNC
1ST MULTIPLEXER
FOR SLAVE K/B1ST MAIN MONITOR
BNC
2ND MULTIPLEXER
2ND MAIN MONITOR
FOR MASTER K/B
BNC
POWER
AC 24V
AL5
AL6
GND
AL7
AL8
GND
COM3
NC3
NO3
COM4
NC4
NO4
AL1
GND
AL2
AL3
GND
AL4
COM1
COM2
NO1
NC1
NO2
NC2
AC+
RX-(TX-)
RX+(TX+)
AC-
(RX-)
FGND
AC+
AC-
(RX+)
GND
RS-485
(RS-422)
(RX+)
(RX-)
RX+(TX+)
RX-(TX-)
AC 24V
POWERPOWER
AC 24V
BNC
AWG # 24
Spot output 1 of the first multiplexer to be connected to 16
th
input of the second multiplexer.
n: User, Spot out of n th to be connected to (15-n) th camera input of the 2nd multiplexer. nth spot
out of the 2nd multiplexer to be connected to the nth use spot monitor. Each user will see the
picture of the selected camera (1~(31-n)) on n th spot monitor of the Mux 2 by selecting camera
No.+Cam. Figure 5
–
Two Multiplexer with Slave Keyboard Controller

12
2.2 Termination & Dip Switch Setting
The first and last devices in an installation (dome and keyboard controller) must have the data
line terminated by setting the DIP switch. Without proper termination, there is potential for
control signal errors. Total length of the cable for communication should not exceed 1.2 km.
Refer to Figure 7 for setting the dome camera and keyboard controller termination.
Termination and Master/Slave: Set the switches according to your configuration.
ON
9J 1 2 3 4 5 6 7 8
S2
Figure 7 – Keyboard DIP Switches
Termination should be On
Cable for communication
Cable for communication
Figure 6
–
Termination and ID Switches.
Termination should be On
When there is more than two branches, a
repeater is required.

13
DOME Multi-
plexer
Sub-
controll
er
Termination
12 3 4 5 6
Controller
7 8
ON ON ON ON SLAVE ON
OFF OFF OFF OFF
reserved MASTER OFF
Factory
Use
Table 1 – S2 Switch Setting
2.3 Keyboard Setup
User need to setup network, passwords and special functions such as Uploading and Downloading
programmed data from the dome cameras. To enter the Keyboard menu, press Ctrl + Menu. You will see
the following menu. Joystick Up/Down scrolls menu items, push the stick to Right to enter the sub-menu.
Configuration
- Key Beep : ON - enable key beep sound,
OFF - Disable beep sound.
- Key-Lock : OFF~60Min - After elapsed setup time, keyboard lock automatically.
OFF - Disable Auto Key-Lock function.
User needs login password to operate Keyboard again.
- Chg User Pin - Change 4digit of user password.
CurrentPin : Enter 4 digits of current user’s password.
NewPin : Enter 4 digits of new password.
ConfirmPin : Confirm 4 digits of new password.
- Chg Admin Pin - Change 4 digits of administrator’s password.
CurrentPin : Enter 4 digits of new password.
NewPin : Enter 4 digits of new password.
ConfirmPin : Confirm 4 digits of new password.
Note) Factory default Administrator’s password is 9999+Enter and user password is 1111+Enter.
If you forgot your own password, contact service personnel or distributor.
- Rescan Domes Scan newly installed dome cameras without turn off the Keyboard power.
- Save and Exit Save the programmed data and return to the previous Menu
(Exit without saving if you press ESC key)
Network Setup properties of devices to be connected.
Configuration
Network
Data Bank
Alarm
Exit

14
- Set Baud rate
Dome : 2400~230K Correspond with dome setting (9600bps)
MUX : 2400~230K
DVR485 : 2400~230K
DVR232 : 2400~230K
Save and Exit
- Com Ports Select the device to be connected on selected port.
Dome : None/Dome …
MUX : None/DUPLEX/TRIPLEX/AUX IN/AUX I/O…
DVR485 : None/ADR/SDR/IDR/AUX IN/AUX I/O…
DVR232 : None/ADR/SDR/IDR/AUX IN/AUX I/O…
Save and Exit Save the programmed data and return to the previous Menu
(Exit without saving if you press ESC key)
Note) AUX IN : auxiliary signal input ( simplex mode)
AUX I/O : when auxiliary signal input , respond to the signal (Half duplex mode)
- Set Slave kbd
Slave kbd : ON/OFF ON- Slave KBD exit, OFF- Not exist.
MUX control : ON/OFF Set accessibility of the multiplexer menu at slave keyboard
Dome Menu: ON/OFF Set accessibility of the dome camera menu at slave keyboard
Release :INF/001~200s INF (Infinite) - Slave Keyboard user never have the control right of the
dome which is selected by master Keyboard users
1 ~ 200s( Second) - After elapse of programmed time since master
Keyboard user use the dome, slave Keyboard user can get the control
right of the dome.
Save and Exit Save the programmed data and return to the previous Menu
- Exit
- Data Bank - Up/Download saved data of the dome
DataBank 1 : 001 001— Data from Dome ID 001 is exist on Bank 1
Upload If you are sure to upload or clear data to the selected dome then
Clear Data press Enter key, ESC key to cancel and exit.
DataBank 2 : Empty
DownLoad If you are sure to download data from the selected dome then
Exit Press Enter key, ESC key to cancel and exit.
- Alarm
- Alarm Check : ON/OFF Whether K/B check the alarm input of domes or not.
On : 32 domes, Off : 64 dome cameras supported.
- Alarm Beep : ON/OFF When dome’s alarm, beep sound on or off
- Exit

15
2.4 Master & Slave Keyboard setting
You can use two keyboards at distant site.
Master keyboard should be setup as following procedure.
1. Check for dip switch the 7th of S2 “OFF”.
2. Press Ctrl + Menu. Check Slave KBD setting “ON”. (Network ▶Set Slave Kbd ▶Slave kbd:ON/OFF)
Slave keyboard need to setup as following procedure.
1. Check for dip switch the 7th of S2 “ON”.
2. If you setup all connection correctly (See Figure 4) and turn on slave keyboard, you can see
following screen.
3. Press Ctrl + Menu. Set the Slave ID to 01
4. Set Slave Node to “B” in case that master keyboard model is HTX-3000 and to “B” in case HTX-2000
SCANDOME II Vxxx
Slave ID = 1
Input Password : xxxx
CAM : 000
←Current Device ID = 1
←Default setting is 9999 for administrator, 1111 for user
←000 means that the controller is not connected to the master keyboard
Slave ID = 1
Slave Node : A / B
←A : HTX-3000 , B : HTX-2000

16
Chapter 3
OPERATION
3.1 Keyboard Lock/Unlock (Hidden command)
When the user leaves the control desk, he may wish to lock the keyboard controller to prevent unauthorized
use.
Pressing 777 + Enter will lock the keyboard controller. Pressing 777 + Enter while the keyboard is locked
will open the password screen. If the correct password is entered, the keyboard controller will return to
normal operation.
If the power is turned OFF and ON while the keyboard is locked, it will ask for the password. Entering the
correct password will cause the keyboard controller to return to normal operation.
** If you forget your own passwords, turn off the keyboard controller, contact distributor to get 4-digit back door
password. This will change the passwords to the factory default 1111 and 9999. Contact your service
personnel to get 4-digit back door password.
3.2 Controlling Multiplexer
Using a multiplexer allows more flexibility in the types of cameras that can be used in a full system. Dome
cameras and regular cameras can be mixed.
The keys PIP, 2x2, 3x3, 4x4, Zoom, Set, etc., are keys that are used to operate the multiplexer.
See Figure x for details.
3.2.1 Selecting Multiplexer
Duplexer : Press Macro/Menu key to enter Multiplexer set up menu and hold down the Enter
Key while navigating using the joystick. (Enter+Joystick)
Triplexer : Push the Jostick to upward with Enter pressed (Enter+Joystick )will show the Mux menu.
It will act like a mouse. Rotatingthe handle clockwise will act like the set key of the
multiplexer. Rotating counterclockwise will act like the ESC key of the Multiplexer.
3.2.2 Dome Camera Selection
There are three types of dome camera selection, No.+Cam, No.+Main and Prev or Next. And with these
selections, the keyboard controller has full control of the selected camera if it is a dome camera.
Single multiplexer configuration
By pressing the camera No. 1to 16+ Cam, you will see the picture of the selected camera through the spot
monitor which connected to the spot output of the multiplexer.
Two multiplexer configurations
By pressing the camera No. 1to 31 + Cam, you can see the picture of the selected camera through the spot
monitor which is connected to the spot output of the second multiplexer.
Spot output of the first multiplexer is connected to the 16th camera input of the second multiplexer.
For example, 1+ Cam will switch the camera 1 to second multiplexer spot output. If the selected camera is
a dome, the keyboard controller has control of it, and you can control all functions of the selected camera
using the keyboard controller.
Pressing the Next or Prev keys will scroll through all connected dome cameras and display them on the
Spot output.

17
Viewing full screen mode ( m + Mux, n + Main)
Select cameras 1 to 16 by pressing the camera number and then Main. The selected camera will appear in
the full screen mode and is under control if it was dome camera.
Even if no camera is connected to the multiplexer input, the screen will show the camera input (see
following example).
To select first multiplexer under control, press 1 + Mux ( m: ID of Mux – up to 128)successively
Multiplexer 1 Keyboard controller
1 1+ Main
2 2+ Main
.
.
15 15+ Main
16 16+ Main
This sequence (No.+Main) is same as pressing the 1, 2, 3…16 buttons on the multiplexer.
To select second multiplexer under control, press 2 + Mux
when a second multiplexer is connected:
Multiplexer 2 Keyboard controller
1 1+ Main
2 2+ Main
3 3+ Main
.
.
16 16+Main
When using two multiplexer configuration, connect the main or spot output of the first multiplexer to the
Camera 16 input of the second multiplexer.
If the spot output of the first multiplexer is connected to the Camera 16 input of the second multiplexer, you
can see selected camera output through the spot output of second multiplexer by pressing camera No. (1to
31) + Cam Successive camera call is valid on two Mux configuration only.
For example: 1+Cam will switch camera 1 to the second multiplexer spot output and you can control all
functions of the selected camera using the keyboard controller.
If you install more than two Multiplexers, the unit number (ID : up to 128) of the Multiplexer and selection of
the Multiplexer must be the same in order to control the Multiplexer with the Keyboard.
Example: If the unit address (number, see page 15) of the Multiplexer is 128, you should press
128 + Mux to control the 128th Multiplexer.
Picture on Spot output monitor (Camera No.1~16+Aux1~4)
Pressing Camera No. 1 to16 + Aux1~ 4 will switch the selected camera number to the specific spot monitor
output of the multiplexer. The selected camera can be a dome camera or a standard camera. The Keyboard
controller maintains control of the previously selected dome camera. It does not change the main output of
the multiplexer.
Example: m+Mux, n+AuxN m: ID of Mux, n:input No. of camera, N:spot output No.
1+MUX, 2+Aux1(~4) will switch camera 2 on multiplexer 1 to the spot output of multiplexer 1.
2+MUX, 3+Aux1(~4) will switch camera 3 on multiplexer 2 to spot output of multiplexer 2.
1+Cam will switch camera 1 to the spot output of multiplexer 1 and the keyboard controller has
control of the selected camera.

18
In a two multiplexer configuration, 18+Cam will switch camera 18 (second camera on Multiplexer
2) to the spot output of multiplexer 2 and the keyboard controller has control of the selected
camera.
31+Cam = camera 15 of the second multiplexer.
3.3 Summary of Keyboard Controls
Cam:001E
ZOOM WIDE ZOOM TELE
IRIS OPENIRIS CLOSE
FOCUS NEAR FOCUS FA
R
MULTIPLEXER
DVR CONTROL
MULTIPLEXERIDR CONTROL
Figure 8 – Keyboard Key map
Figure 9 – J-box Front & Rear
DVR CONTROL

19
3.3.1 Keys for Dome camera
Function Key Label Descriptions
1,2, ... 9,0 1,2, ... 9,0
Camera selection with Cam key.
Function number selection with function keys.
(e.g., 1+Cam, 3+Tour, 5+Scan, 6+Prst)
Camera CAM
Displays the selected camera on the spot out of the multiplexer and allows the
camera to be controlled by the keyboard controller, if the selected camera is a dome
camera.
Full MAIN Camera No. 1~16+Main will display the selected camera full screen
Cancel ESC Cancels current inputs.
Exits from currently running functions or menu, error status, etc.
Alarm ALRM
Disregards all currently activated alarms and turns off the beep temporarily. If alarm
is activated again within the programmed hold time, the timer will restart and beep
again.
Relay ON ON Relay No. 1~4+ ON will activate the selected relay.
Relay OFF OFF Relay No. 1~4+ OFF will disable the selected relay.
Previous PREV Allows the previous dome camera to be controlled manually.
Next NEXT Allows the next higher number dome camera to be controlled manually.
Home HOME Immediately calls Home function.
Deletes selected value or function in programming mode
Global GLBL Sends all cameras to preset (e.g., 1, 2… 55 + Enter/Glbl).
888+Enter/Glbl: Night shot mode, 999+Enter/Glbl: Normal mode
Call Preset
position PRST
Pressing Prst will bring up the preset programming menu.
Recalls preset; e.g.; 1, 2… 31… 240 + Prst
In the preset or tour programming mode, the operator can review the exiting preset
(selected by cursor) by pressing this key.
Tour TOUR Pressing Tour will bring up the tour programming menu directly
Recalls programmed presets or functions sequentially. (e.g., 1 ~ 8+Tour)
Pattern PTRN Pressing Ptrn will bring up the pattern programming menu directly.
Repeats the selected pattern of the current dome camera. (e.g., 1 ~ 4+Ptrn)
Auto Scan SCAN Pressing Scan will bring up the Auto Scan programming menu.
Calls Auto panning function (e.g., 2+Scan repeats Auto Scan 2).
Configuration MENU Enters programming menu.
Ctrl+Menu will invoke Keyboard set up menu
Program PGM
No.+Pgm+Prst will store current view as a preset directly.
No.+Pgm+Tour will open programming menu
No.+Pgm+Scan will open programming menu
Control CTRL
Ctrl+Joystick : In a programming mode (Preset, Pattern, Scan, Privacy….) the
joystick operates as if in the normal control mode.
While pressing and holding down the Ctrl key, all movements of the joystick will start
recording when in the pattern programming menu.
Ctrl+Joystick:, In normal operation mode, manual speed of the joystick control will
be operated in turbo mode. (Max. speed = 380º/sec)
Enter ENTER
Completes entering data for the password or title
ENTER+Joystick : Direction key in DVR remote mode or Mux ( PTZ, Mouse,
Cursor)
Key operation example
Ctrl + Menu : Press and hold down Ctrl Key and press Menu Key
1 + Cam : Press 1 Key, Cam Key sequentially
Ctrl + Joystick : Press and hold down Ctrl Key while manipulate Joystick Handle
Enter + Joystick : Press and hold down Enter Key while manipulate Joystick Handle

20
Manual Focus
Overrides auto focus. Moving the Zoom handle reactivates Auto Focus mode.
Manual Iris
Overrides auto iris. Moving the joystick reactivates Auto Iris mode.
Zoom
Zoom control.
Joystick
Twist
Up / Down
Left / Right
Press(Toggle)
Zoom control (proportional to position).(HID2404CZx model only).
Tilt control, Cursor Up / Down in the PGM. menu
Pan control, Cursor Left / Right or Page scroll in the PGM. Menu
Pressing the joystick toggles between zoom control mode on and off. When zoom
control mode is on, you can see “Z” letter at LCD right down corner.
(joystick up : zoom in & joystick down : zoom out) (HID2404CLx model only).
3.3.2 Keys for Multiplexer
Function Key Label Descriptions
PiP PIP Picture-in-Picture mode
2 by 2 Display 2X2 Displays view of four cameras. The remaining cameras can be sequenced in the
lower-right window.
3 by 3 Display 3X3 Displays view of nine cameras. The remaining cameras can be sequenced in the
lower-right window.
4 by 4 Display 4X4 Displays view of 16 cameras in 1/16-size pictures.
2nd 2ND Second mode of PIP multiplexer. Pressing 2nd+Enter again will return to normal
mode.
Panic record L.REC Put a camera in the Panic Record Mode.
Macro MACRO Same as Menu key in the Duplexer model.
Same as Macro key in the Triplexer model.
Select or
Alarm SEL Same as Select key in the Duplexer model.
Same as Alarm key in the Triplexer model.
Freeze FRZ Freeze the video from the currently selected camera.
Digital Zoom ZOOM Enter the Zoom Mode.
Sequence SEQ Put the multiplexer in the Sequence Mode.
VCR VCR Switch the multiplexer into VCR playback mode.
SET SET This button has several functions. It brings up a Popup Menu, sets selections on the
OSD menus and decreases numbers in the number setup function.
Spot output AUX1 (~4) Displays selected camera as spot output of the current Multiplexer.
(e.g., 2+Aux1 will display camera 2 as a spot output of the current Multiplexer)
Select Mux ID MUX Select Multiplexer (e.g.; 1 or 2+Mux)
Cursor
movement
Enter +
Joystick
Up / Down / Left / Right control in the ZOOM and SET UP mode.
Handle turn clockwise for SET mode.
Handle turn counterclockwise for ESC mode.