Honeywell PRO4200 User manual

September 2020 © 2020Honeywell International, Inc. All rights reserved 800-25698V1 I
-
PRO4200
Two Reader Module
(PRO42R2)
Installation Guide

September 2020 © 2020Honeywell International, Inc. All rights reserved 800-25698V1 II
-
Copyright© 2020 Honeywell. All rights reserved.
All product and brand names are the service marks, trademarks, registered trademarks, or registered
service marks of their respective owners. Printed in the United States of America. Honeywell reserves the
right to change any information in this document at any time without prior notice.
WIN-PAK® is a trademark of Honeywell International, Inc.
Ordering Information
Please contact your local Honeywell representative or visit us on the web at www.honeywellaccess.com
for information about ordering.
Feedback
Honeywell appreciates your comments about this manual. Please visit us on the web at
www.honeywellaccess.com to post your comments.
Discover | Customer Portal
Self-Service Product Support and Learning Management System
https://honeywelldiscovertraining.com/login/discover/default.asp
YouTube | Honeywell Help and Support
https://www.youtube.com/channel/UCBEL6ouNV_LN5lEpYRujMTg/featured

PRO4200 Two-Reader Module User Guide, Document 800-25698V1 iii
Notices
Warnings and Cautions.................................................................................................... . . . . . . . . . . v
Disclaimer.......................................................................................................................... . . . . . . . . . . vi
Compliance........................................................................................................................ . . . . . . . . . vii
CE and WEEE Marking .................................................................................................. . . . . . . . . . vii
Unpacking Procedure....................................................................................................... . . . . . . . . . vii
Shipping Instructions ....................................................................................................... . . . . . . . . . . ix
Limited Warranty ............................................................................................................. . . . . . . . . . . ix
Confidentiality .................................................................................................................. . . . . . . . . . . x
Installing the PRO4200 Two Reader Module
Description ........................................................................................................................ . . . . . . . . . 11
Specification...................................................................................................................... . . . . . . . . . 12
Set Up................................................................................................................................. . . . . . . . . . 13
LED Operation.................................................................................................................. . . . . . . . . . 15
Power.................................................................................................................................. . . . . . . . . . 16
Communications............................................................................................................... . . . . . . . . . 16
Wiring ................................................................................................................................ . . . . . . . . . 17
Wiring Diagram for Connectors TB1,TB7-9 ............................................................... . . . . . . . . . 18
2-Reader Input Module Programming Guide
............................................................................................................................................. . . . . . . . . . 25
CONTENTS

iv www.honeywell.com
(This page is left blank intentionally for double-sided printing.)

Notices
Warnings and Cautions
PRO4200 Two-reader Module User Guide, Document 800-25698V1 v
Notices
Warnings and Cautions
Warning
Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply.
Do not apply power to the system until after the installation has been completed.
Personal injury or death could occur, and the equipment could be damaged beyond
repair, if this precaution is not observed!
Warning: Fire Safety and Liability Notice
Never connect card readers to any critical entry, exit door, barrier, elevator, or gate
without providing an alternative exit in accordance with all fire and life safety codes
pertinent to the installation. These fire and safety codes vary from city to city and you
must get approval from local fire officials whenever using an electronic product to
control a door or other barrier. Use of egress buttons, for example, may be illegal in
some cities. In most applications, single action exit without prior knowledge of what
to do is a life safety requirement. Always make certain that any required approvals are
obtained in writing. DO NOT ACCEPT VERBAL APPROVALS, BECAUSE THEY
ARE NOT VALID.
Honeywell never recommends using the PRO4200 or related products for use as a
primary warning or monitoring system. Primary warning or monitoring systems
should always meet local fire and safety code requirements. The installer must also
test the system on a regular basis by instructing the end user in appropriate daily
testing procedures. Failure to test a system regularly could make the installer liable for
damages to the end user if a problem occurs.
Note: See the Remote Enclosure Installation manuals PRO22ENC1, PRO22ENC2,
PRO22ENC3 or PRO22ENC5 for installation instructions.
Warning:
EARTH ground all enclosures for proper installation.
Warning:
Use suppressors on all door strikes. Use S-4 suppressors for installation. Honeywell
recommends only DC strikes.
Warning: For UL Installations:
• Wiring methods shall be in accordance with the National Electrical Code
(ANSI/NFPA70).
• All interconnecting devices must be UL Listed.
• Not Evaluated by UL for fire, life safety, or burglary applications.
• Do Not Connect To A Receptacle Controlled By A Switch.

Notices
Disclaimer
vi www.honeywell.com
• All interconnecting wire must be UL/ULC Listed, rated and suitable for the
use.
Caution:
IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST BE
FILED WITH THE COMMERCIAL CARRIER RESPONSIBLE.
Caution: Electrostatic discharge can damage CMOS integrated circuits and modules.
To prevent damage, always follow these procedures:
• Use static shield packaging and containers to transport all electronic
components, including completed reader assemblies.
• Handle all ESD sensitive components at an approved static-controlled
workstation. These workstations consist of a desk mat, a floor mat, and an ESD
wrist strap. Workstations are available from various vendors.
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This document and the data in it shall not be duplicated, used, or disclosed to
others for procurement or manufacture, except as authorized by and with the written
permission of, Honeywell, Inc. The information contained in this document or in the
product itself is considered the exclusive property and trade secrets of Honeywell, Inc.
Copyright laws of the United States protect all information in this document or in the
software product itself.
Note: Any use of this product is subject to the terms and acceptance of the Honeywell,
Inc. Software Agreement. Please request a copy from Honeywell, Inc., and review the
agreement carefully.
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component thereof
has caused personal injury or damage to property of others, Customer shall
immediately notify Honeywell in writing of all such claims. Honeywell shall defend
or settle such claims and shall indemnify and hold Customer harmless for any costs or
damages including reasonable attorneys' fees which Customer may be required to pay
as a result of the defective Product or the negligence of Honeywell, its agents, or its
employees.
Customer shall hold harmless and indemnify Honeywell from and against all claims,
demands, losses, and liability arising out of damage to property or injury to persons

Notices
Compliance
PRO4200 Two-reader Module User Guide, Document 800-25698V1 vii
occasioned by or in connection with the acts or omissions of Customer and its agents
and employees, and from and against all claims, demands, losses, and liability for
costs of fees, including reasonable attorneys' fees, in connection therewith.
Compliance
To obtain applicable EU compliance Declaration of Conformities for this product,
please refer to our website,
https://www.security.honeywell.com/All-Categories/access-control-systems/control-p
anels-hardware. For any additional information regarding the compliance of this
product to any EU-specific requirements, please contact:
Honeywell Security & Communications
Honeywell Security - Quality Assurance Dept., Newhouse Industrial Estate
Motherwell
Lanarkshire ML1 5SB
Scotland
United Kingdom
Tel: [phone]
Email: [email protected]
CE and WEEE Marking
Description of the used symbol.
Unpacking Procedure
Caution:
If any damage to the shipment is noticed before unpacking, a claim must be filed with
the commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.
The following steps are used to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all packing materials. They may be used again for reshipment of
the equipment, if needed.
2. Inspect the contents for shortage. If items are missing items, contact the order
entry department at 800-323-4576.
3. Visually check contents. If damage is discovered, perform the following:
CE -Standard -Logo. This product complies with
the harmonized Regulation of the EU
WEEE symbol.It indicates this product is to be
recycling and not been thrown in the dustbin

Notices
Unpacking Procedure
viii www.honeywell.com
• If shipping caused damage to the unit, a claim must be filed with the
commercial carrier.
• If any other defect is apparent, call for a return authorization.

Notices
Shipping Instructions
PRO4200 Two-reader Module User Guide, Document 800-25698V1 ix
Shipping Instructions
To ship equipment back to Honeywell, Inc.:
1. Contact the customer service department at 800-323-4576 before returning
equipment. When you call please have available:
• A description of the problem or reason you are returning the equipment.
• Your original purchase order number, invoice number and if the unit is
still under warranty.
• A new purchase order number if the unit is not under warranty.
2. From the customer service department, obtain the Return Authorization
Number (RMA).
3. Show the RMA number on all packages shipped. Packages which are not
marked with an RMA number will be refused at the factory and returned to
you COD.
4. Carefully pack the equipment for shipment. Use the original packing material
whenever possible.
Limited Warranty
All Products sold or licensed by Honeywell include a warranty registration card which
must be completed and returned to Honeywell by or on behalf of the end user in order
for Honeywell to provide warranty service, repair, credit or exchange. All warranty
work shall be handled through Customer which shall notify Honeywell and apply for a
Return Merchandise Authorization (RMA) number prior to returning any Product for
service, repair, credit, or exchange. Honeywell warrants that its Products shall be free
from defects in materials and workmanship for a period of two years from date of
shipment of the Product to Customer. The warranty on Terminals, Printers,
Communications Products and Upgrade kits is 90 days from date of shipment.
Satisfaction of this warranty shall be limited to repair or replacement of Products
which are defective or defective under normal use. Honeywell's warranty shall not
extend to any Product which, upon examination, is determined to be defective as a
result of misuse, improper storage, incorrect installation, operation or maintenance,
alteration, modification, accident or unusual deterioration of the Product due to
physical environments in excess of the limits set forth in Product manuals. THERE
ARE NO WARRANTIES WHICH EXTEND BEYOND THIS PROVISION. THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS,
IMPLIED OR STATUTORY, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. NO
REPRESENTATION OR WARRANTY OF THE DISTRIBUTOR SHALL EXTEND
THE LIABILITY OR RESPONSIBILITY OF THE MANUFACTURER BEYOND
THE TERMS OF THIS PROVISION. IN NO EVENT SHALL HONEYWELL BE
LIABLE FOR ANY RE-PROCUREMENT COSTS, LOSS OF PROFITS, LOSS OF
USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES TO ANY
PERSON RESULTING FROM THE USE OF HONEYWELL'S PRODUCTS.

Notices
Confidentiality
xwww.honeywell.com
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and
other materials furnished by Honeywell relating to the design, use and service of the
Products shall remain confidential and shall constitute proprietary rights of Honeywell
and Customer agrees to treat such information as confidential. Customer shall acquire
no rights in the design of the Products or the related materials except to use such
information solely for the purpose of and only during the time it sells the Products.
Customer shall not copy the design of any of the Products or use or cause to be used
any Product design or related materials for its own benefit or for the benefit of any
other party. The covenants contained in this section shall remain effective throughout
the term of this Agreement and thereafter unless specifically waived by Honeywell in
writing.

Installing the PRO4200 Two Reader Module
Description
PRO4200 Two-reader module User Guide, Document 800-25698V1 11
Installing the PRO4200 Two Reader
Module
Description
The PRO4200 Two-Reader Module provides support for up to two access control
doors by providing connections for Wiegand or Clock/Data type readers, supervised
inputs, and relay outputs. You can either mount the board in a rack or open and flat. If
you rack-mount the board, only one edge is accessible for wiring; however, a flat
mount increases the amount of available I/O slightly but significantly decreases the
number of boards that can be mounted in one enclosure.
The I/O terminals are organized to support two doors. Starting at the bottom of the
rack-mount side of the board, the connector provides power to the board and
connector provides communication with the Intelligent Controller (PRO42IC and
PRO32IC). The next set of terminals connects reader 2. The next set of terminals
connects the I/O typically associated with reader 2, namely the Door Status and REX
status inputs and the Door Lock and Lock Status relay outputs. Continuing up this
edge the next two connectors provide the reader and associated I/O terminals for
reader 1. The last connector on the rack-mount edge provides terminals for two
additional general-purpose inputs.
When the board is mounted flat, two additional relay outputs and two additional
general-purpose inputs are available along with two dedicated inputs for cabinet
tamper and power fault detection on the opposite edge of the board.
The reader interface accepts a Wiegand signal of Data 1 and Data 0 or a Clock and
Data signal and provides 5VDC or 12VDC reader power, a tri-stated LED control and
buzzer control. Two of the six form-C relay outputs are sized for the inductive load of
door locks and the other four are designed to handle dry-circuit signals. All of the
inputs are capable of four-state supervision except the two dedicated inputs.
Communication to the control panel is accomplished via an RS-485 interface. This
board requires 12VDC input power. When communication to the control panel is lost,
this board can grant access based on facility code only. General purpose outputs will
retain the setting at the time communication was lost. Up to eight facility codes may
be active in each PRO32IC and PRO42IC. Keypad input must follow the reader input
format and is in place of or multiplexed with the reader data.

12 www.honeywell.com
Installing the PRO4200 Two Reader Module
Specification
Specification
The Two-Reader Module is for use in low voltage, class 2 circuits only.
Primary power:
12VDC + 10%, 650mA maximum with 5V readers, 300 mA max. excluding readers
Relay contacts:
• Relays 0 through 1 outputs, Form-C, 5A @ 30VDC, resistive
• Relays 2,3,4, and 5 outputs, Form-C,2A @ 30VDC,resistive
Inputs:
• 8 supervised, End of Line resistors 1k ohm ± 1% tolerance
• 2 unsupervised dedicated inputs
Communication:
Wire requirements:
Mechanical:
Environment:
RS-485 Range 9,600 to 38,400 bps
Power 1 twisted pair, 18AWG(Honeywell 3114 or equivalent
RS-485 24 AWG, 4,000 feet (1,200 m) max., twisted pair with
shield (120, 23pF) (Honeywell 3328 or equivalent)
Inputs 1 twisted pair per input, 30 ohms max.
Outputs As required for the load
Readers 6 conductors, 18AWG, 500 feet (150m) max. shield and
drain
Dimension 5.5" (140 mm) W x 9" (229 mm) L x 1" (25 mm) H
Weight 12 oz. (340 g) nominal
Temperature 0°C to +49°C, operating, -55°C to +85°C, storage
Humidity 0% to 85% RHNC

Installing the PRO4200 Two Reader Module
Set Up
PRO4200 Two-reader module User Guide, Document 800-25698V1 13
Set Up
Table 1: PRO4200 IN Module Jumper Setting
Jumper Setting Default Selected
J1 OFF * Port 1 RS-485 EOL
terminator is not active
ON Port 1 RS-485 EOL
terminator is active
J2 Position 5 Reader 1 Power terminals
provides 5 VDC
Position 12 Reader 1 Power terminal
provides 12 VDC
J3 Position 5 Reader 2 Power terminal
provides 5 VDC
Position 12 * Reader 2 Power terminal
provides 12 VDC
S8 S7 S6 S5 S4 S3 S2 S1 Selection
OFF OFF OFF OFF ON ADDRESS 1*
OFF OFF OFF ON OFF ADDRESS 2
OFF OFF OFF ON ON ADDRESS 3
OFF OFF ON OFF OFF ADDRESS 4
OFF OFF ON OFF ON ADDRESS 5
OFF OFF ON ON OFF ADDRESS 6
OFF OFF ON ON ON ADDRESS 7
OFF ON OFF OFF OFF ADDRESS 8
OFF ON OFF OFF ON ADDRESS 9
OFF ON OFF ON OFF ADDRESS 10
OFF ON OFF ON ON ADDRESS 11
OFF ON ON OFF OFF ADDRESS 12
OFF ON ON OFF ON ADDRESS 13
OFF ON ON ON OFF ADDRESS 14
OFF ON ON ON ON ADDRESS 15

14 www.honeywell.com
Installing the PRO4200 Two Reader Module
Set Up
* = Default
ON OFF OFF OFF OFF ADDRESS 16
ON OFF OFF OFF ON ADDRESS 17
ON OFF OFF ON OFF ADDRESS 18
ON OFF OFF ON ON ADDRESS 19
ON OFF ON OFF OFF ADDRESS 20
ON OFF ON OFF ON ADDRESS 21
ON OFF ON ON OFF ADDRESS 22
ON OFF ON ON ON ADDRESS 23
ON ON OFF OFF OFF ADDRESS 24
ON ON OFF OFF ON ADDRESS 25
ON ON OFF ON OFF ADDRESS 26
ON ON OFF ON ON ADDRESS 27
ON ON ON OFF OFF ADDRESS 28
ON ON ON OFF ON ADDRESS 29
ON ON ON ON OFF ADDRESS 30
ON ON ON ON ON ADDRESS 31
OFF OFF Reserved
OFF ON 9,600 BPS
ON OFF 19,200 BPS
ON ON 38,400 BPS*
OFF Not Used*
S8 S7 S6 S5 S4 S3 S2 S1 Selection

Installing the PRO4200 Two Reader Module
LED Operation
PRO4200 Two-reader module User Guide, Document 800-25698V1 15
LED Operation
The Two-Reader Module uses two onboard LEDs (D1 and D2) to provide status
information during the power-up sequence as well as during normal operation. The
Two-Reader Module also uses two onboard LEDs (D3 and D4) to indicate reader
activity.
In addition to the status LEDs, there are six additional relay status LEDs and eight
input status LEDs on board. The input LEDs flash when there is a fault associated
with the input.When any relay or input is energized or ON, its corresponding status
LED becomes ON also.The LED remains ON for as long as the relay is energized.
The assignment for each relay status LED is shown in the following table:
.The following table lists the LEDs D1 through D4.
Table 2: LED Settings
Mode LED D1 LED D2 Description
Power-up
sequence
ON OFF Start power-up, hardware setup
OFF ON Testing RAM
ON ON Testing ROM and completing
initialization
FLASH ON LED D1 flashes 4 times after power-up
is completed
Normal
Operation
FLASH This is the processor heartbeat LED. It
flashes once every second. A short ON
time (~20% duty cycle) indicates the
board is offline or has lost serial
communication with the Controller
board. A long ON time (~80% duty
cycle) indicates the board is online and
communicating with the Controller
board.
FLASH Flash when there is activity on its Serial
Port.
Table 3: Additional PRO4200 Two Reader Module LEDs
LED number Description
D3 Reader 1 activity
D4 Reader 2 activity
D5 Input 0

16 www.honeywell.com
Installing the PRO4200 Two Reader Module
Power
Power
The Two-Reader Module accepts 12VDC with an operating range of 10 to 14VDC
and consumes a maximum of 300mA of current without readers. Locate power source
as close to this board as possible. Connect power with minimum of 18 AWG wire.The
input voltage is regulated to 5VDC.The regulated voltage or the 12VDC (pass
through) is available for powering the readers. The selection is made via jumpers and
is available at both reader connectors.
Note: POLARITY for 12VDC power is important. Make sure the +12 VDC is connected to
the terminal labeled +12V and the return is connected to the terminal labeled GND.
Communications
The Two-Reader Module communicates to the host controller via an RS-485
interface.The interface allows for multi-drop communication of up to 4,000 feet
D6 Input1
D7 Input 2
D8 Input 3
D9 Input 4
D10 Input 5
D11 Input 6
D12 Input 7
D13 Tampert
D14 Power
D15 Relay 0 status
D16 Relay 3 sttatus
D17 Relay 2 status
D18 Relay 4 status
D19 Relay 1 status
D20 Relay 5 status
Table 3: Additional PRO4200 Two Reader Module LEDs
LED number Description

Installing the PRO4200 Two Reader Module
Wiring
PRO4200 Two-reader module User Guide, Document 800-25698V1 17
(1,200 m) total per port. Use twisted pair (minimum 24 AWG) with shield for
communication. The default speed of this port is 38.4Kbps but it can be downgraded
to 19.2Kbps or 9.6Kbps if the line conditions or receiving equipment require it (see
Table 1 on page 3 for jumper settings and Table 2 on page 4 for DIP switch settings).
For wiring to an RS-485 port:
1. TR+ is the plus side of the transmit and receive differential signal.
2. TR- is the negative side of the transmit and receive differential signal.
3. GND is the signal ground.The wiring for this signal is required and NOT optional.
This signal must NOT be connected to chassis GND.
4. Use 24 AWG low capacitance, twisted-pair, shielded cable (Honeywell 3328 or
equivalent).
Wiring
This section presents information on reader wiring, input wiring, and control output
wiring.
The following figure shows the PRO4200 board and identifies its terminal block pin
assignments.

18 www.honeywell.com
Installing the PRO4200 Two Reader Module
Wiring Diagram for Connectors TB1,TB7-9
Wiring Diagram for Connectors TB1,TB7-9
Figure 1: PRO4200 Two Reader Module: Connectors TB1,TB7-9.
Note: See LED Operation on page 16 for descriptions of LEDs D1-D20.
Note: Reader, Input, and Output addresses on the PRO4200 panel are labeled starting
with address 0. This translates to address 1 in the WIN-PAK per the example below:
DIP SWITCHES
ON
OFF
87654321
TWO READER BOARD Short
together*
Power
RS-485
EOL
EOL
Door Status
Switch
Typical Connection
Egress
Push-Button
Switch
RED
BLACK
BLACK
RED
WHITE
GREEN
S-4
Suppressor
S-4
Suppressor
Door Lock
Door Lock
Separate
Power
Supply
Separate
Power
Supply
-
VDC
+
-
VDC
+
KP-13
Weigand
Keypad
Proximity
Reader
Chassis GND
Inside Panel
Chassis GND
Inside Panel
Voltage is selected by
Jumper J2 On Board
Voltage is selected by
Jumper J2 On Board
RED
BROWN
YELLOW
WHITE
GREEN
BLACK
DRAIN
RED
BROWN
YELLOW
WHITE
GREEN
BLACK
DRAIN
BLACK
RED
D1
D2
D3
D4
D15
D16
D17
D20
D18
D19
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
RS-485 TR+
RS-4845 TR-
RS-485 GND
+ 12V
GND
READER1 V+
READER1 LED
READER1 BZR
READER1 D1
READER1 D0
READER1 GND
IN2
IN2 COMMON
IN3
IN3 COMMON
RELAY2 NO
RELAY2 C
RELAY2 NC
RELAY3 NO
RELAY3 C
RELAY3 NC
READER0 V+
READER0 LED
READER0 BZR
READER0 D1
READER0 D0
READER0 GND
IN4
IN4 COMMON
IN5
IN5 COMMON
IN0
IN0 COMMON
IN1
IN1 COMMON
RELAY0 NO
RELAY0 C
RELAY0 NC
RELAY1 NO
RELAY1 C
RELAY1 NC
K 1
K 3 K 4
K 2
K 5 K 6
J 1 - RS-485
Termination
J 3
J 2
J 4
* Rack Mount Conguration
CardRack PWR
&
Com Harness* (Rack
Mount Only)
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
1
2
3
1
2
3
4
5
6
1
2
3
4
1
2
3
4
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
PRO4200 Device PRO4200 Address WIN-PAK Address

Installing the PRO4200 Two Reader Module
Wiring Diagram for Connectors TB1,TB7-9
PRO4200 Two-reader module User Guide, Document 800-25698V1 19
Note: The SIO board port for a PRO42IC in WIN-PAK is port 6 and is set as the
default.
Each reader port supports a reader with TTL (D1/D0, Clock/Data), F/2F, or 2-wire
RS-485 signaling. Power to the reader is selectable:
Input on supervised F/2F readers may be unsupervised or supervised (supervised
shown).
Reader Wiring
The following Honeywell reader module numbers have been approved by UL for use
with the PRO4200: OM40BHONA, OM55BHONA, OP10HONE, OP30HONE,
Reader\ Input\ Output 0 1
Reader\ Input\ Output 1 2

20 www.honeywell.com
Installing the PRO4200 Two Reader Module
Wiring Diagram for Connectors TB1,TB7-9
OP40HONE, OP90HONE, OT30HONA, OT31HONA, OT35HONA, and
OT36HONA.
Each reader port supports a reader with TTL interface. Power to the reader is
selectable as 5VDC or 12VDC (pass-through). This selection is done by setting the
jumpers J2 for reader 1 and J3 for reader 1. Set jumper at position "5" for 5VDC or
"12" for pass-through 12VDC. The factory defaults set J2 and J3 to "5".
For wiring to a reader port
The LED control terminal in each reader port can be configured via host software to
support one-wire single or bi-colored reader LED. An example of the most common
configuration is shown below. If Beeper Control is not used, its terminal can be
programmed to be the second wire for the two-wire bi-colored reader LED.
To fully utilize each reader port, a 6-conductor cable (18AWG) is required. Reader
port configuration is set via host software
Input Wiring
Inputs 0 to 7 may be configured to use normally open or normally closed contacts and
non-supervised or supervised (with standard ±1% tolerance 1K ohm). Four of these
Table 4: Settings for Wiring to a Reader Port
Terminal Typical Wire
Color
Wiegand
Reader
Clock/Data
Readers
1 Red Power (5 or
12 Vdc)
Power (5 or 12
Vdc)
2 Brown LED control LED control
3 Yellow Beeper
Control
Beeper
Control
4 White Data 1
Signal
Clock Signal
5 Green Data 0
Signal
Data 0
Signal
6 Black Common Common
Table 5:
LED Output-> High Tri- Stated Low
Single Color LED LED ON LED OFF LED OFF
Bi- Color LED Green LED ON Both LEDs OFF Red LED ON