Honeywell SILEN KNIGHT IDP-Relay-6 User manual

K200-15-00 1 I56-2732-003
INSTALLATION AND
MAINTENANCE INSTRUCTIONS
BEFORE INSTALLING
If the modules will be installed in an existing operational
system, inform the operator and local authority that the
system will be temporarily out of service. Disconnect the
power to the control panel before installing the modules.
This system contains static sensitive components. Always
IDP-Relay-6
Six Relay Control Module
SPECIFICATIONS
Normal Operating Voltage: 15-32 VDC Stand-By
Current: 1.45 mA
Alarm Current: 32 mA (assumes all six relays
have been switched once and
all six LEDs solid on)
Temperature Range: 32°F to 120°F (0°C to 49°C)
Humidity: 10 to 85% Non-condensing
Dimensions: 6.8˝ H × 5.8˝ W × 1.0˝ D
Maximum IDC
Wiring Resistance: 40 ohms
Accessories: IDP-ACB cabinet and chassis
Wire Gauge: 12-18 AWG
Relay Current: 30 mA/Relay Pulse (15.6
mS pulse duration) pulse
under panel control
ground yourself with a proper wrist strap before handling
any circuits so that static charges are removed from the
body. The housing cabinet should be metallic and suit-
ably grounded.
NOTICE: This manual should be left with the owner/
user of this equipment.
GENERAL DESCRIPTION
The IDP-Relay-6 Six Relay Control Module is intended
for use in an intelligent alarm system. Each module is
intended for Form-C switching applications, which do
not require wiring supervision for the load circuit. A
single isolated set of dry relay contacts is provided for
each module, which is capable of being wired for either
normally open or normally closed for each operation.
Each module has its own address. A pair of rotary code
switches is used to set the address of the first module
from 01 to 94. The remaining modules are automatically
assigned to the next five higher addresses. Provisions are
included for disabling a maximum of three unused mod-
ules to release the addresses to be used elsewhere. Each
IDP-Relay-6 module also has panel controlled green LED
indicators. The panel can cause the LEDs to blink, latch
on, or latch off.
Contents include:
(6) 1 × 3 Terminal Blocks
(1) 1 × 4 Terminal Blocks
(2) 11/4˝ (32mm) Stand offs
(4) Machine Screws
(2) Nuts
(1) Shunt (NOTE: For the disable position, not more
than one shunt shall be installed at the same time)
COMPATIBILITY REQUIREMENTS
To ensure proper operation, this module shall be connected
to a compatible Silent Knight system control panel.
CURRENT RATING MAXIMUM VOLTAGE LOAD DESCRIPTION APPLICATION
3 A 30 VDC Resistive Non-coded
2 A 30 VDC Resistive Coded
.9 A 110 VDC Resistive Non-coded
.9 A 125 VDC Resistive Non-coded
.5 A 30 VDC Inductive (L/R=5ms) Coded
1 A 30 VDC Inductive (L/R=2ms) Coded
.3 A 125 VAC Inductive (PF=.35) Non-coded
1.5 A 25 VAC Inductive (PF = .35) Non-coded
.7 A 70.7 VAC Inductive (PF=.35) Non-coded
2 A 25 VAC Inductive (PF=.35) Non-coded
WARNING
All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed)
state during shipping. To ensure that the switch contacts are in their correct state, modules must be made to communi-
cate with the panel before connecting circuits controlled by the module.

2
1
3
Figure 3: Installation of rear module only, method one
Step 1: Insert the bottom of the IDP-Relay-6 module
down into a rear slot on the chassis.
Step 2: Carefully swing the upper edge of the board
back towards the back of the chassis until it
touches the two standoffs.
Step 3: Align two 4-40 screws with the two standoffs
and tighten.
Step 4: Address and wire the modules according to the
instructions in this manual.
The steps in Figures 4a and 4b describe and illustrate mod-
ule installation when the rear chassis position and the posi-
tion in front of it will be filled. Front position installation
is possible only if the rear position is filled with a module.
1
Figure 4a: Installation of IDP-Relay-6 module in a
rear chassis position, method two
Step 1: Insert the bottom edge of the IDP-Relay-6
module down into a rear slot of the chassis.
Step 2: Carefully swing the bottom edge of the board
towards the back of the board until it touches the
short standoff attached to the chassis.
Step 3: Align the long standoff with the short standoff
and tighten.
COMPONENTS
The following is a description of the IDP-Relay-6 mount-
ing framework:
• One or two IDP-Relay-6 modules can be installed in a
IDP-ACB cabinet
The IDP-ACB cabinet has a built-in chassis that will ac-
commodate one or two IDP-Relay-6 modules.
0
1
2
3
456789
0
78
6
5
4
3
21
910
11
12
13
14
15
BASE ADDRESS
ADDRESS
DISABLE
NONE
ONE
TWO
THREE
0
1
2
3
456789
0
78
6
5
4
3
21
9
BASE ADDRESS
ADDRESS
DISABLE
NONE
ONE
TWO
THREE
Figure 1: IDP-ACB Cabinet
The front IDP-Relay-6 module positions of each chassis
are offset below the rear IDP-Relay-6 module positions
so that all of the status indicators are visible. For cabinet
dimensions refer to IDP-ACB instruction manual.
INSTALLATION STEPS
1. Cabinet Mounting
In a clean, dry area, mount the backbox using the four
holes provided in the back surface of the cabinet.
Backbox
Mounting
Holes
Figure 2: Typical mounting hole locations
2. Module Installation
There are two methods for installing a module in the
rear position of a chassis. Method one is for installa-
tion of a rear module only, when no module will be in-
stalled in front of it. Refer to Figure 3 for instructions.
Method two is for installation of a rear module when
another module will be installed in the chassis position
in front of it. Refer to Figures 4a and 4b for method
two. All necessary screws and standoffs are supplied
with the modules.
K200-15-00 2 I56-2732-003
C0235-00
C0234-03
C0249-00
C0244-00

2
1
3
Figure 4b: Installation of IDP-Relay-6 module in
front chassis position
Step 1: Insert the bottom edge of the IDP-Relay-6
module down into a front slot of the chassis.
Step 2: Carefully swing the upper edge of the board
towards the back of the chassis until it touches
the 11/4˝ (31.75mm) standoffs installed on the
rear module.
Step 3: Align two 4-40 screws with the two standoffs and tighten.
Step 4: Address and wire the modules according to
the instructions in this manual.
WIRING
NOTE: All wiring must conform to applicable local
codes, ordinances, and regulations.
1. Install module wiring in accordance with the job draw-
ings and appropriate wiring diagrams.
2. Make electrical connections by stripping approxi-
mately 1/4˝ (6.35mm) of insulation from the end of the
wire sliding the bare end of the wire under the clamp-
ing plate, and tightening the clamping plate screw.
3. Set the address on the modules per the job drawing.
Use the rotary code switches to set the address of the
first module (between 01 and 94). The remaining mod-
ules are automatically assigned to the next five higher
addresses. For example, if the base address switch is
set to 28, the next five modules will be addressed to
29, 30, 31, 32, and 33. DO NOT set the lowest address
above 94, as the other modules will be assigned to
nonexistent addresses.
4. A shunt is provided to disable a maximum of three
unused modules. Modules are disabled from the high-
est address and work downward. If two modules are
disabled, the lowest four addresses will be functional,
while the highest two will be disabled. For example, if
the shunt for Address Disable is placed on “two” and
the base address switch is set to 28, the modules will
be assigned to 28, 29, 30 and 31.
NOTE: The IDP-Relay-6 must have power cycled for
shunt changes to take effect.
NOTES:
• The relay contacts on the IDP-Relay-6 may be
connected to either a power-limited or non power-
limited source, this wiring must remain separated by at
least 1/4˝ (6.35 mm) from all power-limited wiring.
• Power-limited circuits must employ type FPL, FPLR, or
FPLP cable as required by Article 760 of the NEC.
• For easier wiring, assign all power-limited wiring to one
side rather than alternating with non power-limited.
PROGRAMMING
The modules are programmed as modules in each system
according to the programming instructions in the appro-
priate FACP manual.
K200-15-00 3 I56-2732-003
C0245-00

K200-15-00 4 I56-2732-003
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
0
1
2
3
456789
0
78
6
5
4
3
21
9
N.C.
N.O.
COMMON
ADDRESS 5
N.C.
N.O.
COMMON
ADDRESS 4
N.C.
N.O.
COMMON
ADDRESS 3
N.C.
N.O.
COMMON
ADDRESS 2
N.C.
N.O.
COMMON
ADDRESS 1
N.C.
N.O.
COMMON
ADDRESS 0
– + – +
SLC
BASE ADDRESS
ADDRESS
DISABLE
NONE
ONE
TWO
THREE
6.8"
5.8"
FROM PANEL
OR PREVIOUS DEVICE
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
SEE PANEL INSTRUCTION
MANUAL FOR
WIRE REQUIREMENTS
TO NEXT
DEVICE
–+
–
+
–
+
NC
NO
COMMON
RELAY CONNECTIONS
STATUS
INDICATORS
C0250-03
Figure 5: Wiring and programming the IDP-Relay-6 module
7550 Meridian Circle
Maple Grove, MN 55369-4927
763-493-6455; 800-328-0103
Fax: [phone]
http://www.silentknight.com
© 2006 Silent Knight 2/06