Honeywell Exi-/MaxLED T2 User manual

GB
Wireless
Plug-in Module Exi-/MaxLED T2
http://www.hls-nordic.com
Dimensional drawings:
Honeywell Life Safety AS, Postboks 263, 1372 Asker
MaxLED Installation:
ExiLED Installation:
13
2
4
6
5
4
13
2
46
5
30mm
46mm
24mm
19mm
30mm
22mm

GB
Honeywell Life Safety AS, Postboks 263, 1372 Asker http://www.hls-nordic.com
5. Tighten the nut and washer from the outer side (tool recommended). Make sure there are no sharp bends on the
antenna cable.
2. Disconnect mains from the luminaire, slid and open the luminaire case, (ref. ExiLED inst. manual) and disconnect the
battery. Plug the module.
MaxLED (See pictures on page 1):
6. Refit the top lid, assemble the luminaire and reconnect mains.
4. Remove nut and washer from the antenna cable and pass the cable through the side hole.
4. Screw on the antenna.
You are now ready to setup the module for network communication. For network setup refer to the wireless network
comissioning manual.
6. Screw on the antenna.
1. Screw on the extension antenna cable.
3. Remove cap.
2. Disconnect the battery and connect the internal extension antenna cable to the WL Module.
1. Disconnect mains from the luminaire, slide the luminaire of the bracket. Remove the top lid.
The device comes with 4 label stickers that contain a Unique identification code (UID) that is hexadecimal formatted in
4 bytes. An example UID is 45 90 DB FA. It is advised to stick one sticker on the module and one sticker on the luminary
that the module will be fitted in. The two remaining stickers may be placed on a printed floor plan, text lists etc.
3. Plug the module.
5. Reconnect the battery and confirm LED operation.
ExiLED (See pictures on page 2):
7. Reconnect the battery and confirm LED operation. Assemble the luminaire and reconnect mains.
Function
Bottom LED (red): Indicates initialization
Button functionality
This device has three indication LEDs.
Steady on:
Top LED (green): RF connection status
The device has established direct connection to a single Gateway Device.
The device is disconnected.
Received signal strength (RSSI)
RSSI is very good.
RSSI is good.
RSSI is acceptable for reliable communication.
RSSI is not acceptable for reliable communication.
The device has established connection to a single Router Device, and no alternatives
exist on the same hop level.
The device has established connection to a Router Device, and at least one more
Router Device is available on the same hop level, as an alternate route
(redundant connection).
The device has established direct connection to a Gateway Device, and at least one
more Gateway Device is available for alternate routing (false condition).
The module is not initialized correctly. In this case you have to press for more than
2 seconds the push button, in order to re-initialize the module.
The module is working properly.
A status message will be issued to the gateway device of the wireless network.
The router module will restore to its factory default settings. This is extremely useful
in case of an error setting during wireless network installation.
Flashing 5 times per sec.:
Flashing 5 times per sec.:
Middle LED (green):
Flashing 5 times per sec.:
Flashing 2 times per sec.:
Flashing 2 times per sec.:
Flashing 2 times per sec.:
Flashing 1 sec. on / 1 sec. off:
Flashing 1 sec. on / 1 sec. off:
Short press:
Flashing 2 sec. on / 2 sec. off:
Press more than 2 sec.:
No light:
Technical description
Part no.
IP Rating
Ambient temperature range
Relative Humidity
Operation voltage
Power Consumption < 0.2W
Plug-in Module Wireless Exi-/MaxLED T2
138091.17
2.7-3.3V DC
o
5 to 40 C
< 95%
IP20
At the end of their useful life the
packaging and product should be
disposed of via a suitable recycling
centre.
Do not dispose of with your normal
household waste.
Do not burn.