Honeywell ATC928G3000 User manual

WIRELESS BINDING GUIDE
A step-by-step guide for binding wireless heating controls

This WIRELESS BINDING
GUIDE provides simple
step-by-step instructions
for binding wireless
heating controls.
It’s assumed the devices are
appropriately installed and
powered up ready for binding.
For full installation
instructions please refer
to the Installation Guide of
the individual devices.

2
Contents
Binding to a Wi-Fi evohome
Controller (ATC928G3000)................................5
Digital Room Thermostat (DTS92)................................ 6
Mixing Valve Controller (HM80)..................................... 7
Radiator Controller (HR92)................................................ 8
Radiator Controller (HR80)................................................ 9
Room Temperature Sensor (HCF82)..........................10
Room Temperature Sensor (HCW82) ....................... 11
Single Zone Thermostat (T87RF)................................ 12
Underfloor Heating Controller (HCE80/HCC80) .. 13
Wireless Cylinder Thermostat (CS92).......................14
Wireless Relay Box (BDR91) Boiler ............................. 15
Wireless Relay Box (BDR91) Sundial Valve ..............16
Wireless Relay Box (BDR91) Zone Valve....................17
Wireless Relay Box (HC60NG).......................................18
Wireless OpenTherm Bridge (R8810)....................... 19
Binding to a evohome
Controller (ATC928G2000)............................. 21
Digital Room Thermostat (DTS92)............................. 22
Mixing Valve Controller (HM80).................................. 23
Radiator Controller (HR92)..............................................24
Radiator Controller (HR80)............................................. 25
Remote Access Gateway (RFG100)............................ 26
Room Temperature Sensor (HCF82)..........................27
Room Temperature Sensor (HCW82) ....................... 28
Single Zone Thermostat (T87RF)................................ 29
Underfloor Heating Controller (HCE80/HCC80) .. 30
Wireless Cylinder Thermostat (CS92).......................31
Wireless Relay Box (BDR91) Boiler ............................. 32
Wireless Relay Box (BDR91) Sundial Valve ............. 33
Wireless Relay Box (BDR91) Zone Valve................... 34
Wireless Relay Box (HC60NG)...................................... 35
Wireless OpenTherm Bridge (R8810)....................... 36

3
Contents
Binding to a Digital Room
Thermostat (DTS92) ............................................ 37
Wireless Relay Box (BDR91)........................................... 38
Wireless OpenTherm Bridge (R8810)....................... 39
Binding to a Single Zone
Thermostat (T87RF) ............................................ 41
Remote Access Gateway (RFG100).............................42
Wireless Relay Box (BDR91)........................................... 43
Wireless OpenTherm Bridge (R8810)....................... 44
Binding to a Programmable
Thermostat (CM900RF) .................................... 45
Wireless Relay Box (BDR91)........................................... 46
Wireless Relay Box (HC60NG).......................................47
Wireless OpenTherm Bridge (R8810)....................... 48
Binding to a Programmable
Thermostat (CM700RF)..................................... 49
Wireless Relay Box (BDR91)........................................... 50
Wireless Relay Box (HC60NG).......................................51
Wireless OpenTherm Bridge (R8810)....................... 52
Binding to a Programmer or
Timer (ST9000RF)................................................ 53
Digital Room Thermostat (DTS92)............................. 54
Wireless Cylinder Thermostat (CS92)...................... 55
Wireless Relay Box (BDR91) Boiler ............................. 56
Wireless Relay Box (BDR91) Sundial Valve ............. 57
Wireless OpenTherm Bridge (R8810)....................... 58

4

5
Wi-Fi evohome Controller (ATC928G3000)
Binding to a
Wi-Fi evohome Controller (ATC928G3000)

6
Wireless connectivity Guide
To bind a Digital Room Thermostat (DTS92) to a Wi-Fi evohome Controller
(ATC928G3000) as the room temperature sensor in a zone...
On the evohome Controller
1Press and hold SETTINGS for 5 seconds
2Press the green tick
3Press ZONE CONFIGURATION
4Press on the required zone
5Press TEMPERATURE SENSOR
6Press REMOTE SENSOR
7Press the green tick
On the Digital Room Thermostat
8Press and hold for 2 seconds
to put the unit into standby
9Press and together for 3
seconds – it should display 'INst'
10 Press – it should display 'COnt'
11
Press three times – it should display 'CLr'
12 Press once to clear any previous binding data
13 Press – it should display 'COnt'
14 Press once to send the binding
signal to the evohome Controller
You should receive a SUCCESS message on the
evohome Controller. If not go back and re-bind.
Digital Room
Thermostat (DTS92)
Wi-Fi evohome Controller
(ATC928G3000)

7
Wi-Fi evohome Controller (ATC928G3000)
To bind a Mixing Valve Controller (HM80) to a Wi-Fi evohome
Controller (ATC928G3000) “mixing valve” zone...
On the evohome Controller
1Press and hold SETTINGS for 5 seconds
2Press the green tick
3Press ZONE CONFIGURATION
4Press on the required zone
5Press HEATING TYPE
6Press MIXING VALVE
7Press the green tick
On the Mixing Valve Controller
8Press and hold both buttons on the
Mixing Valve Controller for 4 seconds
until the red light flashes
On the evohome Controller
9Press the bind button
You should receive a SUCCESS message on the
evohome Controller. If not go back and re-bind.
The Mixing Valve Controller will not provide a
heat demand to the boiler. If you want this zone to
provide a heat demand change the Heating Type
from 'MIXING VALVE' to 'ZONE VALVES' once the
Mixing Valve controller is bound. There's no need
to re-bind any device – The Mixing Valve Controller
will still operate as intended and the evohome
Controller will send the heat demand to the boiler.
Mixing Valve Controller
(HM80)
Wi-Fi evohome Controller
(ATC928G3000)

8
Wireless connectivity Guide
To bind a Radiator Controller (HR92) to a Wi-Fi evohome
Controller (ATC928G3000) “radiator valve” zone...
On the evohome Controller
1Press and hold SETTINGS for 5 seconds
2Press the green tick
3Press ZONE CONFIGURATION
4Press on the required zone
5Press RF DEVICE BINDING
6Press the forward arrow
On the Radiator Controller
7Press the button once − it
should display UNBOUND
8Press and hold the button for a further
5 seconds until it displays BIND
9Press the button once – it
should display BINDING
On the evohome Controller
10 Press the bind button
You should receive a SUCCESS message on
both the evohome Controller and the Radiator
Controller. If not go back and re-bind.
Radiator Controller
(HR92)
Wi-Fi evohome Controller
(ATC928G3000)