Honeywell GENT Mimic LED Driver Card Instruction manual

These instructions cover the Mimic LED Driver
Card (S4-34600) and Connection converter
(S4-34494), which are designed to be used in
Custom panels.
The Mimic LED Driver connects to a Master Repeat
Card which in turn connects to a loop circuit of a
Vigilon fire system. Each Mimic LED Driver Card
can control up to 768 LEDs and this leaflet covers
the connection of up to 2 Mimic LED Driver Cards.
The Connector converters that holds the terminals
for wiring LEDs.
Custom Panel
LED selection
Only use high efficiency Red,Amber or Green
LEDs with a Mimic LED Driver Card.
"Do not use Blue or White LEDs as these are
not suitable for use with the Mimic LED Driver Card.
Compatibility
The Mimic LED Driver Cards are compatible for use
in Vigilon system where the Control panel has
specific MCC/MCB software, see technical data
section. The Master Repeat Card is configured
using the Mimic Configuration Tool.
4188-951_issue 2_01/12_Part 1_Mimic LED driver 1
Data and Installation
Mimic LED Driver Card
S4-34600 & S4-34494
by Honeywell
S4-34600
Mimic LED Driver Card
S4-34494
Connection Converter
26-way
300mm ribbon cable
20-way
200mm Flat flexible cable
B
A
01 L1 02 L2 0C LC P9
LN
N
P17
DANGER
BT+ BT-
+
RS485 0V 24V
-
WRITE PROTECT
BUZZER
DISABLE
P8
DANGER
DO NOT
REMOVE
L N
P5
FS2
FS4
P16
P4
P2
P1
SW3
PB2
WD1
P14
P7
USB
FS3
2A(QB)
RESET
Mimic Repeat Card
P3
ADDRESS
P2
BOARD
UPSIDEDOWN
ROTATE
P1
P5
IN
P16P15P14P13P12P11
P4
OUT
Mimic
LED Driver
Card 2
WARNING
Removal of
cover exposes
live parts
DANGER
P3
ADDRESS
P2
BOARD
UPSIDEDOWN
ROTATE
P1
P5
IN
P16P15P14P13P12P11
P4
OUT
Mimic
LED Driver
Card 1
Connector
Converter 6
Connector
Converter 1
LED Bank 1 (768 LEDs)LED Bank 2 (768 LEDs)
24610812 14 16 18 20 22 26 24
1359711 13 15 17 19 21 25
23
24610812 14 16 18 20 22 26 24
1359711 13 15 17 19 21 25
23
24610812 14 16 18 20 22 26 24
1359711 13 15 17 19 21 25
23
24610812 14 16 18 20 22 26 24
1359711 13 15 17 19 21 25
23
Maximum of up to
1536 LEDs can be
controlled with
2 Mimic LED Driver
Cards
01 L1 02 L2 0C LC P9
LN
P16
Custom Panel
Backbox
Door
20 way
cable
26 way
cable
Vigilon device loop To mains fused spur unit
Address
P3
Address
P3
B
++
--
No link fitted
One link fitted
**
*No links are fitted here
for this application.
Links set LED
board orientation.
A
B

Mounting
It is recommended that the Mimic LED Driver Cards are mounted inside a Custom panel using suitable PCB
standoffs, there are 6-3mm PCB fixing holes provided on the card. The Connection converters are mounted
on 35mm DIN rails. The LEDs and associated wiring must also be contained inside the same enclosure for
mechanical protection.
"The designer of the Custom panel in which the Mimic LED Driver Cards,Connection converters and LEDs are
mounted must ensure the panel enclosure is EMC compliant and is CE marked.
Cables
The internal connection from the Connection converter to each LED inside the Custom panel is made using
a standard PVC cable. Each LED can be positioned a maximum of up to 3m cable distance away from the
terminals of a Connection Converter.
For recommendations on loop cable type refer to the manual supplied with the Vigilon control panel.
Earth
The Custom panel must be earthed. The loop cable screen must be continued through the Custom panel,
whether the earth is connected to the Custom panel or not.
"
Do not use any part of building structure for earthing.
Mains supply
The mains supply to the Custom panel must be via an unswitched 5A fused spur unit. A disconnect device
must be provided to disconnect both poles and must have a minimum gap of 3mm. The disconnect device
should be available as part of the building installation and must be easily accessible after installation is
complete.
&
Before removal of any card or disconnection of any cable from the Custom panel ensure both mains and battery supplies
are disconnected.
Battery supply
Data and Installation Mimic LED Driver Card
2 4188-951_issue 2_01/12_Part 1_Mimic LED driver
FS2
3.15A(T)
Ceramic
(Anti Surge)
Battery Fuse
BT+ BT-
+
RS485 0V 24V
-
BUZZER
DISABLE
DANGER
DO NOT
REMOVE
P5
FS2
P1
SW3
PB2
WD1
P14
P7
USB
FS3
2A(QB)
DANGER
WARNING
Removal of
cover exposes
live parts.
++
--
Master Repeat Card
Black
Red
Battery lead
Link lead
6V 7Ah Battery
6V 7Ah Battery
Leave the final connection of the battery for the Servicing organisation.
This connection is made during power up and commissioning.
You can use 1 - 12V 7Ah battery (VSRPT-BATT)
or 2 - 6V 7AH batteries as shown.(VSRPT-BATT-A3)

To connect multiple Mimic LED Driver Cards
You can daisy chain up to two Mimic LED driver cards to the Master Repeat Card using the 20 way flat
flexible cable .
How to connect a flat flexible cable
Hold the locking tab by the edges and lift it upwards a little jand insert the flat flexible cable kinto the
socket. Ensure the cable contacts are on the opposite side to the locking tab. Push down the locking tab l
to lock the flat flexible cable.
How to disconnect a flat flexible cable
Hold the locking tab by the edges at positions mand lift it upwards one side at a time nto disengage the flat
flexible cable. Then remove the cable ofrom the socket.
To connect the ribbon cables from Mimic LED Driver card to Connection converters
Connect one end of the 26 way ribbon cable to the IDC header on the Mimic LED Driver card (P11) and
the other end to a Connection converter. The Mimic LED Driver card can accommodate up to6-26way
ribbon cable for wiring LEDs via 6 Connection converters.
4188-951_issue 2_01/12_Part 1_Mimic LED driver 3
Mimic LED Driver Card Data and Installation
P13
P4
OUT
P5
IN
Master Repeat Card
P4
OUT
P5
IN
Mimic LED Driver
Card 1
To connect a flat flexible cable
P13
P13
To disconnect a flat flexible cable
Mimic LED Driver
Card 2
B B
A
B
24610812 14 16 18 20 22 26 24
1359711 13 15 17 19 21 25
23
Connector
Converter 1
P16P15
P14
P13
P12P11
Mimic LED Driver Card
26 way ribbon cable
24610812 14 16 18 20 22 26 24
1359711 13 15 17 19 21 25
23
Connector
Converter 2
24610812 14 16 18 20 22 26 24
1359711 13 15 17 19 21 25
23
26 way ribbon
cables
Connector
Converter 6
Connection to 128 LEDsConnection to 128 LEDsConnection to 128 LEDs
A

Relationship between Terminals and external LEDs
Technical data
S4-34600 Mimic LED Driver Card
Dimensions 160mm height x 150mm width x 30mm depth
Card weight 150g
Storage temperature -30ºC to +70ºC
Operating temperature -10ºC to +60ºC
Relative Humidity Up to 95% - Temperature +5ºC to +45°C (Non condensing)
LED output per
Mimic LED Driver Card
Up to 768 high efficiency LEDs can be driven by a Mimic LED Driver Card
Each LED can be 3m cable distance away from the Connection converter.
Use only high efficiency Red,Amber or Green LEDs.
Vigilon Panel
compatibility
Fully compatible with LPC = V3.93 / V4.35 & MCC/MCB = V3.94 / V4.37.
Data and Installation Mimic LED Driver Card
Gent by Honeywell reserves the right to revise this publication from time to time and make changes to the content hereof without
obligation to notify any person of such revisions of changes.
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK Website: www.gent.co.uk
Telephone: [phone] Technical support: www.gentexpert.co.uk Fax (UK): [phone]
4 4188-951_issue 2_01/12_Part 1_Mimic LED driver
by Honeywell
Do not dispose of with your normal household waste.
Do not burn.
WEEE Directive:
At the end of their useful life, the packaging,
product and batteries should be
disposed of via a suitable recycling centre.
At the end of their useful life, the packaging,
product and batteries should be disposed of
via a suitable recycling centre and in
accordance with national or local legislation.
24610
812 14 16 18 20 22 26
24
1359
7
11 13 15 17 19 21 25 23
LED
Ref +-
LED
Ref +-
LED
Ref +-
LED
Ref +-
LED
Ref +-
LED
Ref +-
LED
Ref +-
LED
Ref +-
126 8925 817 24 825 23 833 22 841 21 849 20 857 19 8
226 710 25 718 24 726 23 734 22 742 21 750 20 758 19 7
326 611 25 619 24 627 23 635 22 643 21 651 20 659 19 6
426 512 25 520 24 528 23 536 22 544 21 552 20 560 19 5
526 413 25 421 24 429 23 437 22 445 21 453 20 461 19 4
626 314 25 322 24 330 23 338 22 346 21 354 20 362 19 3
726 215 25 223 24 231 23 239 22 247 21 255 20 263 19 2
826 116 25 124 24 132 23 140 22 148 21 156 20 164 19 1
65 18 873 17 881 16 889 15 897 14 8105 13 8113 12 8121 11 8
66 18 774 17 782 16 790 15 798 14 7106 13 7114 12 7122 11 7
67 18 675 17 683 16 691 15 699 14 6107 13 6115 12 6123 11 6
68 18 576 17 584 16 592 15 5100 14 5108 13 5116 12 5124 11 5
69 18 477 17 485 16 493 15 4101 14 4109 13 4117 12 4125 11 4
70 18 378 17 386 16 394 15 3102 14 3110 13 3118 12 3126 11 3
71 18 279 17 287 16 295 15 2103 14 2111 13 2119 12 2127 11 2
72 18 180 17 188 16 196 15 1104 14 1112 13 1120 12 1128 11 1
Terminal numbers on a
Connection converter
LED Ref 1
Connection Converter
LED Ref 34

The illumination of LEDs connected to the Connection Converters of a Mimic LED Driver Card is
determined by the configuration held at the Master Repeat Card (MRC).
The following information show how to load a LED Driver template file and associate LED shapes with
terminals of Connection converter and configure each LED shape with a system event using the Mimic
Configuration tool.
How to load the 'Mimic LED Driver template.s19' file
The Master Repeat Card is configured using the Mimic Configuration Tool. The tool requires an 'LED
Driver template' file to be loaded to configure a Mimic LED Driver Card connected to the MRC. To open
the template file follow steps jto m.
How Mimic LED ‘Shapes’ relate to the Mimic LED Driver Card and Terminals
The 'LED Driver template' file has defined LED shapes of each possible LED that can be connected to the
Connection converters associated with a Mimic LED Driver Card.
4188-951_issue 2_01/12_Part 2_Mimic LED driver 1
Commissioning information
Mimic LED Driver Card
S4-34600 & S4-34494
by Honeywell
Do not alter these settings as they are
pre defined in the LED Driver template file.
7 P16_24_8
Shape number 7
Related to IDC Connector P16
on the Mimic LED Driver Card
IDC connector P16 is ribbon
cabled to Connection connector
and its terminals:
Terminal 24 is + LED
Terminal 8 is - LED
When the linked function is active
you can define the LED action to:
P13
Master Repeat Card
P4
OUT
P5
IN
Mimic LED Driver
Card 1
P15
P13
P14
P11
P12
Connection
converter 1
Connection
converter 6
Address
P9
24610
812 14 16 18 20 22 26
24
1359
711 13 15 17 19 21 25
23
Connection Converter
P16
From the directory
select ‘ ’
to load the configuration template
for the .
DataFiles
LED Driver card 1
LED Driver template.s19
If two LED Driver Cards are fitted inside
a Custom panel, both daisy chain
connected to a ,
then you will need another
.
Master Repeat Card
LED Driver
template file.

How to link Mimic LED ‘Shapes’ to system events
Each used LED shape must be linked with a system event, such as:
¨Device fire
¨Device fault
¨Channel fire
¨Channel fault
¨Zone fire
¨Zone fault
¨Card fire
¨Card fault or
¨Supervisory Command Build.
Below is a typical example that shows how a shape can be linked to a zone:
For full information on configuration see the instructions supplied with the Mimic Configuration tool.
Test
Test the Custom panel and ensure it gives the correct indication for the configured Vigilon System event.
Commissioning information Mimic LED Driver Card
Gent by Honeywell reserves the right to revise this publication from time to time and make changes to the content hereof without
obligation to notify any person of such revisions of changes.
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK Website: www.gent.co.uk
Telephone [phone] Fax (UK): [phone]
2 4188-951_issue 2_01/12_Part 2_Mimic LED driver
by Honeywell
Drag and drop an LED ‘Shape’ onto the
a system event in the system tree. This
example shows being dropped
onto so the two are linked.
Shape 5
Zone 5,
The LED Shape here is linked to
.
So when has a fire event then the LED connected
to terminals and will be lit (On).
Note also the is associated with
IDC Connector on the
5 P16_26_8
Zone 5 - Fire
Zone 5
26 8
P16
Connection Converter
Connection Converter
Mimic LED Driver Card.