Honeywell UDC 1000 Micro-Pro User manual

4.3 OPERATOR MODE DISPLAYS 4-12
4.4 TUNING THE CONTROLLER MANUALLY 4-13
4.4.1 Controllers Fitted with Output 1 Only 4-13
4.4.2 Controllers Fitted with Output 1 and Output 2 4-14
4.5 SELF-TUNE AND PRE-TUNE FACILITIES 4-15
4.6 EXIT FROM SET UP MODE 4-15
5 RS485 SERIAL COMMUNICATIONS (ASCII) 5-1
5.1 RS485 COMMUNICATIONS 5-1
5.2 COMMUNICATIONS ENABLE/DISABLE 5-1
5.3 SELECTION OF COMMUNICATIONS CHANNEL ADDRESS 5-1
5.4 PHYSICAL REQUIREMENTS 5-1
5.4.1 Character Transmission 5-1
5.4.2 Line Turn-Round 5-1
5.4.3 Communications Protocol 5-2
5.4.4 Type 1 Message 5-4
5.4.5 Type 2 Message 5-5
5.4.6 Type 3 Message 5-5
5.4.7 Type 4 Message 5-6
5.5 INDIVIDUAL PARAMETERS 5-6
5.5.1 Input Parameters 5-6
5.5.2 Output Parameters 5-7
5.5.3 Setpoint Parameters 5-9
5.5.4 Alarm Parameters 5-9
5.5.5 Tuning Parameters 5-10
5.5.6 Status Parameters 5-11
5.6 ERROR RESPONSE 5-11
6 RS485 SERIAL COMMUNICATIONS (MODBUS) 6-1
6.1 INTRODUCTION 6-1
6.2 MODBUS FUNCTIONS SUPPORTED 6-1
6.3 MESSAGE FORMATS 6-1
6.4 PARAMETER NUMBERS 6-6
7 CONFIGURATION MODE 7-1
7.1 ENTRY INTO CONFIGURATION MODE 7-1
7.2 HARDWARE DEFINITION CODE 7-2
7.3 CONFIGURATION MODE PARAMETERS 7-3
(v)

7.3.1 Input Range 7-3
7.3.2 Output 1 Action 7-4
7.3.3 Alarm 1 Type 7-4
7.3.4 Alarm 2 Type 7-5
7.3.5 Alarm Inhibit 7-5
7.3.6 Output 2 Usage 7-6
7.3.7 Output 3 Usage 7-7
7.3.8 Communications Link Baud Rate 7-8
7.3.9 Communications Protocol 7-8
7.3.10 Communications Address 7-8
7.3.11 Cold Junction Compensation Enable/Disable 7-8
7.3.12 Lock Code 7-9
7.4 ALARM HYSTERESIS OUTPUTS 7-9
7.5 EXIT FROM CONFIGURATION MODE 7-10
8 INTERNAL LINKS AND SWITCHES 8-1
8.1 REMOVING THE CONTROLLER FROM ITS HOUSING 8-1
8.2 REMOVING/REPLACING THE OUTPUT2/OUTPUT3 OPTION PCBs 8-3
8.3 REMOVING/REPLACING THE RS485 COMMUNICATIONS OPTION
PCB OR DUAL SETPOINT SELECTION INPUT OPTION PCB 8-3
8.4 REPLACING THE CONTROLLER IN ITS HOUSING 8-4
8.5 SELECTION OF INPUT TYPE AND OUTPUT 1 TYPE 8-4
8.5.1 Input Type 8-5
8.5.2 Primary Output (Output 1) Type 8-5
8.6 OUTPUT 2 TYPE/OUTPUT 3 TYPE 8-6
Appendices
A PRODUCT SELECTION GUIDE A-1
B PRODUCT SPECIFICATION B-1
C ADDITIONAL INFORMATION ON TPSC MODELS OF THE UDC1000
CONTROLLER C-1
C.1 PRODUCT SELECTION GUIDE C-1
C.2 PRE-TUNE AND SELF-TUNE FACILITY C-1
C.3 CONNECTIONS AND WIRING C-1
C.4 RELAY OUTPUTS C-2
C.5 SET UP PARAMETERS C-3
C.5.1 Motor Travel Time C-3
(vi)