Honeywell COMFORTTEMP 4 HCE640 Series User manual

IMPORTANT
SAFETY INSTRUCTIONS
WARNING – READ AND SAVE THESE OPERATING
AND SAFETY INSTRUCTIONS BEFORE USING THIS
HEATER. IF YOU DO NOT UNDERSTAND THESE
INSTRUCTIONS OR PRODUCT LABELS PLEASE
CALL OUR CUSTOMER REPRESENTATIVES AT
18004770457 FOR ASSISTANCE BEFORE USING
THIS PRODUCT.
Warning – Failure to follow any of these safety
instructions could result in fire, injury, or death.
YOUR RESPONSIBILITIES
Electrical appliances may expose people to hazards
that can cause severe injury as well as death. The use
of electrical products may create hazards that include,
but are not limited to, injury, fire, electric shock and
electrical system damage. These instructions are
intended to provide you with the information you need
to use the product correctly and to avoid such hazards.
When using electrical appliances, basic precautions
should always be followed to reduce risk of fire,
electric shock, and injury to persons including the
following:
1. Warning – Read all instructions before using
this heater.
2. Warning – This heater is hot when in use. To
avoid burns, DO NOT let bare skin touch hot
surfaces. Use handles when moving this heater.
Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at
least 3 feet (0.9 m) from the front of the heater
and keep them away from all sides of the heater.
3. Warning – Extreme caution is necessary when
any heater is used by or near children or invalids,
and whenever the heater is left operating and
unattended.
4. Warning – ALWAYS unplug heater when not
in use.
5. Warning – DO NOT operate any heater with
a damaged cord or plug, any heater that
malfunctions, or any heater that has been
dropped or damaged in any manner. Discard
heater or return heater to authorized service
facility for examination and/or repair.
6. Warning – For residential use only.
7. Warning – DO NOT use outdoors.
8. Warning – This heater is not intended for use
in bathrooms, laundry areas, and similar indoor
locations. DO NOT locate heater where it may
fall into a bathtub or other water container.
9. Warning – DO NOT run cord under carpeting.
DO NOT cover cord with throw rugs, runners,
or similar coverings. DO NOT route cord under
furniture or appliances. Arrange cord away from
traffic areas and where it will not be a tripping
hazard.
10. Warning – This appliance has a polarized plug
(one blade is wider than the other). To reduce
the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety feature.
11. Warning – This heater draws 12.5 amps during
operation. To prevent overloading a circuit,
DO NOT plug the heater into a circuit that already
has other appliances working.
COMFORTTEMP™4
CERAMIC HEATER
HCE640, HCE643, HCE645 SERIES
Air Purifier
Heater
Fan
Humidifier
Filter
Air Purifier

2
ABOUT CERAMIC TECHNOLOGY
12. Warning – It is normal for the plug to feel warm
to the touch; however, a loose fit between the
AC outlet (receptacle) and plug may cause
overheating and distortion of the plug. Contact a
qualified electrician to replace loose or worn outlet.
13. Warning – To disconnect the heater, first turn off
the product, then grip the plug body and pull it
from the wall outlet. DO NOT pull by the cord.
14. Warning – DO NOT insert or allow foreign objects
to enter any ventilation or exhaust opening as
this may cause electric shock, fire, or damage
to the heater.
15. Warning – To prevent a possible fire, DO NOT
block air intakes or exhaust in any manner.
DO NOT use on soft surfaces, like a bed, or where
openings may become blocked.
16. Warning – A heater has hot and arcing or
sparking parts inside. DO NOT use it in areas
where gasoline, paint or flammable liquids are
used or stored.
17. Warning – Use this heater only as described in this
manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or
injury to persons.
18. Warning – ALWAYS plug heater directly into
a wall outlet/receptacle. DO NOT use with an
extension cord or relocatable power tap
(outlet/power strip).
19. Warning – NEVER tamper with this product
or attempt to fix it. Any tampering with, or
modification of this product can result in serious
injury, death, or fire. DO NOT open. Risk of electric
shock. There are no user serviceable parts inside.
20. Warning – DO NOT remove product labels
that contain warnings or safety instruction.
21. Caution – The output of this heater may vary
and its temperature may become intense enough
to burn exposed skin. Use of this heater is not
recommended for persons with reduced sensitivity
to heat or an inability to react to avoid burns.
22. Caution – Before cleaning, or storage, or when
not in use, turn the product’s controls to the OFF
position and unplug the heater from the electrical
outlet and allow to cool.
23. Caution – Place the heater on a firm, level, open
surface free from obstructions and at least 3 feet
(0.9 m) away from any combustible materials.
DO NOT use on an unstable surface such as
bedding or deep carpeting. Be sure the heater
is not in a position where it may be tripped over
by small children or pets.
24. Caution – If your home has aluminum wiring
have a licensed electrician check your receptacle’s
connections. When using a 1500 watt heater,
aluminum wire connections can cause a safety issue.
25. SAVE THESE
INSTRUCTIONS
• Ceramic heaters generate heat by passing electricity through heating elements embedded in ceramic plates.
• In the Honeywell ComfortTemp™ 4 Ceramic Heater, air is drawn into the back of the heater by a fan, and then
pushed through the ceramic element and out the front of the heater to gently introduce warm air into the room.
• This type of heating technology provides consistent, even heating.
• For best heat output, place heater on the floor and allow it to run for 510 minutes.

3
SET UP
MOVING THE HEATER
• The Honeywell ComfortTemp™ 4 Ceramic Heater requires no assembly. Simply unpack heater and save all
packaging materials for off-season storage.
• Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9m) away from any
wall or combustible material.
• DO NOT use on an unstable surface such as bedding or deep carpeting.
• BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE TRIPPED OVER BY CHILDREN OR PETS.
• This heater is equipped with a Cool Touch handle for your convenience.
• Turn off the heater.
• Allow it to cool for ten minutes.
• Unplug heater and move.
OPERATION
• NOTE: NEVER LEAVE AN OPERATING HEATER
UNATTENDED
• Plug the heater into a polarized 120V outlet.
DO NOT FORCE THE POLARIZED PLUG INTO
THE OUTLET; it will only fit one way.
• With 90° oscillation, the Honeywell ComfortTemp™
4 Ceramic Heater is versatile and designed to be
placed in the center of the room or closer to the wall
(at least 3 feet away) for maximum convection room
heating.
• Turn heater on by pressing the Power Button ( ).
The Power Indicator will illuminate and the heater
will start in the highest level setting (Heat Blast).
• The heater has two operational modes, which can be
chosen using the red switch on the back of the unit
(Fig. 2):
- Continuous heating ( ) – heater will run until it
is manually shut off.
- Auto ShutOff ( ) mode - heater will
automatically shut off after 8 hours each time that
you use the heater. This is a built-in safety feature
to help ensure the heater isn’t accidentally left on
for an extended period of time.
NOTE: See the SafeGuard® Auto ShutOff feature section for more information on this feature.
• This heater comes pre-set from the factory with the Auto ShutOff mode engaged. When the unit is turned on, the
Auto ShutOff icon ( )will be illuminated on the top of the controls. All features are functional while operating in
the Auto ShutOff mode.
• Should you NOT want the heater to automatically shut off after 8 hours, switch to Continuous heating by simply
pressing the red switch on the back of the unit. Once selected, the Continuous heat icon ( ) will illuminate on
the top of the control panel.
Fig. 1
Power
Button
Heat
Levels
Continuous
Timer
Heat
Setting
Heat
Level
Indicator
Auto Shut-Off
Oscillate
NOTE: Controls/features will vary slightly by model
Fig. 2 Auto Shut-Off Continuous

4
• To select a heat setting, press ( ). There are 4 comfort settings available to choose from - Gentle Warmth,
Cozy, Toasty, Heat Blast - with each setting designed to provide both a unique heat and sound level based on
your desired needs.
NOTE: see next section for an overview of each of the heat settings.
• Press the Timer Button ( ) to select 1, 2, 4, or 6 hour setting. The heater will run for that chosen period in the
selected setting/mode, counting down the hours and automatically shutting the heater off after the selected
time has passed.
• The ComfortTemp™ 4 Ceramic Heater has an oscillation feature. Press the Oscillate Button ( ) to turn on
or off the oscillation function.
• To shut the heater off, press the Power Button ( ) and the heater will begin Powering Down. The heater will
shut off after counting down 10 seconds to cool down the internal components.
• It is important to allow the heater to run through the cool down phase. DO NOT unplug the heater until it has
completed the cool down phase.
4 COMFORT SETTINGS THAT YOU ADJUST TO YOUR NEEDS
SAFEGUARD® AUTO SHUT-OFF FEATURE
Once your heater is ON, use the heat setting control button ( )
on the front panel to select the desired heat setting for your needs.
Your heater will start on the highest setting (Heat Blast) each time
you turn on the heater. Below is a handy reference to help select
the heat option that best suits your desired comfort level. (Fig. 3)
GENTLE WARMTH – (LOW HEAT)
This setting provides a soft, more personal touch of warmth.
COZY – (MEDIUM HEAT)
Ideal for personal and small areas, this setting slightly steps up
theheatoutputforsoothing,comfortingheat.
TOASTY – (MODERATE-HIGH HEAT)
Gradually increasing the heat level, this setting is perfect for
creating that comforting room environment.
HEAT BLAST – (HIGH HEAT)
Choose this maximum heat setting to quickly remove chill and deliver comforting, quick heat.
The Honeywell ComfortTemp™ 4 Ceramic Heater is enhanced with a SafeGuard® Auto ShutOff feature. This
innovative feature is designed to automatically shut the heater off after 8 hours of continuous use and provides
an extra layer of protection for peace-of-mind.
How it works: By default, the ComfortTemp™ 4 Ceramic Heater comes with the Auto ShutOff feature engaged.
If you chose to operate the heater in the Auto ShutOff mode ( ), the heater will shut off automatically after 8
hours every time the heater is used, unless the heater is turned off prior to the 8 hour auto-off time. All features
are functional while operating in the Auto ShutOff feature. If you choose to disengage this feature, the unit will
operate in the Continuous heat mode ( ) .
• Press the SafeGuard® Auto ShutOff switch on the
back of the unit (Fig. 4) to select either the Auto Shut-
Off or Continuous heating modes. The corresponding
icon will illuminate on the controls to indicate which
mode you are in.
Fig. 4 SafeGuard® Auto Shut-Off
Heat
Setting
Fig. 3

5
SAFEGUARD® MOTION SENSOR FEATURE (HCE645 Series only)
REMOTE CONTROL (HCE643 and HCE645 Series only)
The Honeywell ComfortTemp™ 4 Ceramic Heater (Model series HCE645 only) is equipped with a SafeGuard®
Motion Sensor feature. This motion sensor feature identifies objects that may obstruct the normal flow of heat
from the unit, shutting the unit off when necessary, for an additional level of protection.
How It Works: If an object remains too close to the front of the heater for too long - 6 inches or closer for more
than a few seconds - the Motion Sensor light on the front of the unit (Fig. 5) will blink as a warning that there is an
obstruction. If the object is not removed, the sensors will disable the heat, turning the heater off until the object
is removed. The heater will restart after a few seconds once the object is removed.
• Press the SafeGuard® Motion Sensor Button ( ) (Fig. 6) to turn this feature on or off.
The Honeywell ComfortTemp™ 4 Ceramic Heater (Model Series HCE643
and HCE645 only) can be controlled using the remote (Fig. 7). This remote
uses a button cell type battery which comes included in the remote.
• To activate the battery, simply pull the plastic tab.
• All functions may be controlled with the remote with the exception
of choosing which operational mode you prefer (Auto ShutOff or
Continuous Heating). This must be done manually using the red switch
on the back of the unit.
• Place remote control in the holder located in the handle area in the back of
the heater when not in use.
Fig.5
Fig. 7
Fig. 6
SafeGuard® Motion Sensor Light
Remote Control
SafeGuard® Motion Sensor Button

6
SAFETY FEATURES
CLEANING AND STORAGE
The Honeywell ComfortTemp™ 4 Ceramic Heater is equipped with several devices and features for added protection:
• A 360° tip-over switch that disables the heater if it is tipped in any direction.
• A high temperature safety sensor prevents overheating.
• This heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater should
it operate at a higher than normal temperature. If activated, the unit will need to be replaced.
• This heater was built using a high temperature plastic and has a cool to touch housing and handle.
• This heater is designed with thermal insulated wiring for heat resistance and reinforced wire connections
to help protect against loose connections.
• This heater also has a SafeGuard® Auto ShutOff feature. If selected, this feature is designed to automatically
shut the heater off after 8 hours of continuous use.
• The HCE645 Series models have a SafeGuard® Motion Sensor that shuts the heater off if an object
gets too close to the motion sensor.
It is recommended that the Honeywell ComfortTemp™ 4 Ceramic Heater be cleaned at least once a month and
before off-season storage.
• Turn Off ( ) and unplug heater. Allow unit to cool for 10 minutes.
• Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES, POLISHES
OR ANY CHEMICAL SOLUTION.
• Before storing, clean the Ceramic Heater using the above-mentioned steps. Wrap the cord around the unit.
Place in its original box and store it in a cool, dry place.
• This heater does not disassemble.
TROUBLESHOOTING
Problem Solution
If your Honeywell ComfortTemp™
4 Ceramic Heater shuts off
unexpectedly or fails to operate,
one of your heater safety features
may have been activated to
prevent overheating.
• Be sure heater is plugged in and that the electrical outlet is working.
• Check for any obstructions. If you find an obstruction, turn the heater
OFF ()and unplug it.
• Allow the heater to cool completely, then remove the obstruction. Wait at
least 10 minutes, then re-plug the heater in and follow the OPERATION
instructions.
Model(s) Unit Dims Amps Unit Voltage Max Watts Max BTUs
HCE640 Series 7.9” L x 7.9” W x 23.4” H 12.5 120V, 60Hz 1500 5118
HCE643 Series 7.9” L x 7.9” W x 23.4” H 12.5 120V, 60Hz 1500 5118
HCE645 Series 7.9” L x 7.9” W x 23.4” H 12.5 120V, 60Hz 1500 5118
PRODUCT SPECIFICATIONS

7
You should first read all instructions before
attempting to use this product.
A. This 3 year limited warranty applies to repair
or replacement of product found to be
defective in material or workmanship. This
warranty does not apply to damage resulting
from commercial, abusive, unreasonable use
or supplemental damage. Defects that are
the result of normal wear and tear will not be
considered manufacturing defects under this
warranty. KAZ IS NOT LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY
NATURE, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT
IS LIMITED IN DURATION TO THE DURATION
OF THIS WARRANTY. Some jurisdictions do not
allow the exclusion or limitation of incidental or
consequential damages or limitations on how
long an implied warranty lasts, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and
you also may have other rights which vary from
jurisdiction to jurisdiction. This warranty applies
only to the original purchaser of this product
from the original date of purchase.
B. At its option, Kaz will repair or replace this
product if it is found to be defective in material or
workmanship.
C. This warranty does not cover damage resulting
from any unauthorized attempts to repair or from
any use not in accordance with the instruction
manual.
CUSTOMER SERVICE
Questions or comments
Call us toll-free at: 18004770457
E-mail: consumerrel[email protected]
Or visit our website at: www.HoneywellPluggedIn.com
Please be sure to specify the model number.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE
CONTACT CONSUMER RELATIONS FIRST OR SEE
YOUR WARRANTY. DO NOT RETURN THE HEATER
TO THE ORIGINAL PLACE OF PURCHASE. DO
NOT ATTEMPT TO OPEN THE MOTOR HOUSING
YOURSELF, DOING SO MAY VOID YOUR WARRANTY
AND CAUSE DAMAGE TO THE PRODUCT OR
PERSONAL INJURY.
3 YEAR LIMITED WARRANTY
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that
may cause undesired operation.

IMPORTANTES
INSTRUCCIONES DE
SEGURIDAD
ADVERTENCIA – LEA Y GUARDE ESTAS
INSTRUCCIONES DE OPERACIÓN Y DE SEGURIDAD
ANTES DE USAR ESTE CALEFACTOR. SI NO ENTIENDE
ESTAS INSTRUCCIONES O ETIQUETAS DEL PRODUCTO
POR FAVOR LLAME A NUESTROS REPRESENTANTES
DE SERVICIO AL CLIENTE AL 18004770457 PARA
OBTENER AYUDA ANTES DE USAR ESTE PRODUCTO.
Advertencia – El incumplimiento de seguir cualquiera
de estas instrucciones de seguridad puede resultar en
incendio, heridas o la muerte.
SUS RESPONSABILIDADES
Los aparatos eléctricos pueden exponer a las personas a
peligros que pueden causar heridas severas así como la muerte.
El uso de productos eléctricos pueden ocasionar peligros que
incluyen, pero no están limitados a, heridas, incendio, descarga
eléctrica y daño al sistema eléctrico. Estas instrucciones están
pensadas para proporcionarle la información que necesita para
usar el producto correctamente y evitar tales riesgos.
Cuando utilice aparatos eléctricos, debe seguir
siempre las precauciones básicas para reducir el
riesgo de incendio, descarga eléctrica y heridas a
personas incluyendo lo siguiente:
1. Advertencia – Lea todas las instrucciones antes
de usar este calefactor.
2. Advertencia – Este calefactor se calienta cuando está
en uso. Para evitar quemaduras, NO permita que la
piel descubierta toque las superficies calientes. Use
las asas cuando mueva este calefactor. Mantenga los
materiales inflamables, como muebles, almohadas,
sábanas, papeles, ropa y cortinas alejados al menos
0.9 m (3 pies) de la parte frontal de calefactor y de
todos los lados del calefactor.
3. Advertencia – Es necesaria precaución extrema
cuando cualquier calefactor sea utilizado por o
cerca de niños o discapacitados, y siempre que el
calefactor se deje funcionando y sin supervisión.
4. Advertencia – SIEMPRE desconecte el calefactor
cuando no esté en uso.
5. Advertencia – NO opere ningún calefactor con
el cable o el enchufe dañados, o después de un
malfuncionamiento, caída o daño de cualquier
tipo. Deseche el calefactor o regréselo al centro
de servicio autorizado para revisión y/o reparación.
6. Advertencia – Sólo para uso residencial.
7. Advertencia – NO use en exteriores.
8. Advertencia – Este calefactor no está diseñado
para usarse en baños, lavanderías y áreas interiores
similares. NO coloque el calefactor donde pueda
caer en la bañera u otro contenedor de agua.
9. Advertencia – NO pase el cable debajo de la
alfombra. NO cubra el cable con alfombrillas, tapetes
u otras cubiertas similares. NO pase el cable debajo
de muebles o aparatos eléctricos. Coloque el cable
lejos de áreas de tráfico y donde no cause tropiezos.
10. Advertencia – Este calefactor cuenta con un
enchufe polarizado (una clavija es más ancha
que la otra). Para reducir el riesgo de descarga
eléctrica, este enchufe está diseñado para
encajar en un tomacorriente polarizado sólo de
manera unidireccional. Si el enchufe no encaja
completamente en el tomacorriente, inviértalo. Si
aún no encaja, contacte a un electricista calificado.
NO intente anular esta característica de seguridad.
CALEFACTOR DE CERÁMICA
COMFORTTEMP™4
SERIES HCE640 y HCE643 y HCE645
Air Purifier
Heater
Fan
Humidifier
Filter
Air Purifier

10
ACERCA DE LA TECNOLOGÍA CERÁMICA
11. Advertencia – Este calefactor utiliza 12.5
amperes durante su operación. Para evitar una
sobrecarga, NO enchufe el calefactor a un circuito
que ya tenga otros aparatos funcionando.
12. Advertencia – Es normal que el enchufe se sienta
caliente al tacto; sin embargo, una conexión suelta
entre la salida de CA (tomacorriente) y el enchufe
puede provocar sobrecarga y deformación del
enchufe. Pida a un electricista capacitado que
cambie el tomacorriente flojo o defectuoso.
13. Advertencia – Para desconectar el calefactor, primero
apague el aparato, después sujete el enchufe y
sáquelo del tomacorriente. NO tire del cable.
14. Advertencia – NO introduzca ni permita que
entren objetos extraños por las aberturas de
ventilación o salida ya que pueden causar descarga
eléctrica, incendio, o daño al calefactor.
15. Advertencia – Para prevenir un posible incendio,
NO tape de ninguna manera las entradas o salidas
de aire. NO use sobre superficies blandas, como la
cama, o donde las aberturas puedan taparse.
16. Advertencia – Un calefactor contiene en su
interior piezas calientes que generan arcos
voltaicos o chispas. NO lo utilice en áreas donde
se use o almacene gasolina, pintura o líquidos
inflamables.
17. Advertencia – Use este calefactor sólo como
se describe en este manual. Cualquier otro uso
no recomendado por el fabricante puede causar
incendio, descarga eléctrica, o heridas a personas.
18. Advertencia – SIEMPRE conecte el calefactor
directamente en el tomacorriente/receptáculo.
NO use con un cable de extensión o un
tomacorriente móvil (enchufe/contacto múltiple).
19. Advertencia – NUNCA manipule este producto
o intente arreglarlo. Cualquier manipulación con,
o modificación de este producto puede resultar
en heridas graves, muerte, o incendio. NO lo abra.
Riesgo de descarga eléctrica. No hay piezas útiles
en el interior para el usuario.
20. Advertencia – NO quite las etiquetas del producto que
contengan advertencias o instrucciones de seguridad.
21. Precaución – La cantidad de calor que emite
este calefactor es variable y su temperatura
puede llegar a ser lo suficientemente intensa para
quemar la piel expuesta. El uso de este calefactor
no es recomendable para personas con menor
sensibilidad al calor o incapaces de reaccionar
para evitar quemaduras.
22. Precaución – Antes de limpiar, o guardar, o
cuando no esté en uso, APAGUE los controles
del aparato y desconecte el calefactor del
tomacorriente y permita que se enfríe.
23. Precaución – Coloque el calefactor sobre una superficie
firme, nivelada y abierta, libre de obstáculos, al menos
a 0.9 m (3 pies) de distancia de cualquier material
inflamable. NO use sobre superficies inestables como la
cama o alfombras gruesas. Asegúrese que el calefactor
no esté en un lugar en donde los niños pequeños o
mascotas puedan tropezarse con el.
24. Precaución – Si su hogar cuenta con cableado
de aluminio permita que un electricista autorizado
revise las conexiones de los tomacorrientes. Cuando
utilice un calefactor de 1500 watts, las conexiones
del cableado de aluminio pueden causar problemas
de seguridad.
25. GUARDE ESTAS
INSTRUCCIONES
• Los calefactores de cerámica generan calor al pasar la electricidad a través de las resistencias integradas en las
placas de cerámica.
• En el Calefactor de Cerámica ComfortTemp™ 4 de Honeywell, el aire es succionado por un ventilador hacia la parte
posterior del calefactor, pasando a través del elemento de cerámica y finalmente saliendo por la parte delantera del
calefactor para distribuir gradualmente aire caliente por la habitación.
• Este tipo de tecnología de calefacción proporciona calor constante y uniforme.
• Para obtener una mejor salida de calor, coloque el calefactor en el piso y permita que opere durante 510 minutos.