Honeywell Enraf 1010 CB Owner's manual

Programming Manual
Load Computer 1010 CB

Honeywell Enraf
2000 Northfield Court,
Roswell, GA 30076
U.S.A.
Tel: [phone]
Email: [email protected]
www.honeywellenraf.com
4418024 - Revision 1
April 2010
© 2010 Honeywell International Inc.

iii Model 1010 Application Pack CB Part No.: 4418024 - Rev. 21
Programming Manual
Table of Contents
CHAPTER 1 Overview
1.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1.2 Terminology and Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
CHAPTER 2 Programming Mode
2.1 Entering and Exiting Programming Mode. . . . . . . . . . . . . . . . . . . . . . . . .2-1
2.2 Navigating in Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.3 Entering or Selecting Values in Programming Mode. . . . . . . . . . . . . . . .2-3
2.4 Exiting the Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.5 Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
CHAPTER 3 Display Contrast (1)
3.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
CHAPTER 4 System (2)
4.1 System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2 General Setup (21). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
4.2.1 Language Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
4.2.2 Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
4.2.3 System of Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
4.2.4 Batch Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
4.2.5 Transaction Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
4.2.6 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
4.2.7 Authorisations/Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
4.2.8 Timeouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
4.2.9 Bay Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
4.3 Loading Options (22). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4.4 General Purpose Inputs (23). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-13
4.5 General Purpose Outputs (24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
4.6 Configure Deadman (25). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-19
4.7 Communications (26) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
4.7.1 Port n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
4.7.2 Terminal Automation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-21
4.7.3 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-22
4.8 Configure Messages (27) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-22
4.8.1 Initial Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-23
4.8.2 Manager Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-24
4.8.3 Deadman Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25
4.8.4 GP Input Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25
4.8.5 Permissive Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-26
4.8.6 System Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-28

iv Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
4.8.7 Arm Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-29
4.9 Opto Outputs (28) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
4.9.1 Opto Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-30
CHAPTER 5 Loading Arms (3)
5.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.2 Configure Arm n (3n). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.2.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.2.2 Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
5.2.3 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
5.2.4 Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
5.2.5 Alarm Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
5.2.6 Additive Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
CHAPTER 6 Metering Lines (4)
6.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
6.2 Configure Line n (4n) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.2.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.2.2 Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.2.3 K Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.2.4 Signal Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6.2.5 Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
6.2.6 Overrun Quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14
6.2.7 Unauthorised Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14
6.2.8 Minimum Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-15
6.2.9 Accumulated Totals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-15
6.2.10 Meter Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-15
CHAPTER 7 Product Streams (5)
7.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
7.2 Configure Streams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
CHAPTER 8 Additive Lines (6)
8.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
8.2 Configure Additive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
8.3 External Additive Lines (621) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
8.4 Additive Line Setup (622) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
8.4.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
8.4.2 EFT Mini-Pak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
8.5 Internal additive Lines (61) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
8.5.1 Name/Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3
8.5.2 Alarm setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4
8.5.3 K-Factor Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-6
8.5.4 Meter Factor Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-6

v Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
CHAPTER 9 Recipes (7)
9.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
9.2 CONFIGURE RECIPE (7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
CHAPTER 10 Authorisation Entry Mode
10.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
10.2 Entering Authorisation Entry Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
10.3 Navigating in Authorisation Entry Mode. . . . . . . . . . . . . . . . . . . . . . . . .10-4
10.3.1 Edit ID’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-4
10.3.2 Erase ID Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-5
10.3.3 Search For an ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-6
10.3.4 Retrieve an ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-7
10.3.5 Edit Master IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-7
Glossary

vi Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
Intentionally left blank.

1 - 1 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
CHAPTER 1 OVERVIEW
1.1 Description
This manual describes the setup procedures for the Model 1010 loading
system.
It is intended for managers or supervisors who may be required to do
the following:
Change the setup parameters
Program personnel and/or vehicle ID numbers for authorisation
purposes.
1.2 Terminology and Conventions
In this document, “instrument” refers to the generic Model 1010 loading
system, and “computer” refers to the attached computer, Distributed
Control System (DCS), Load Rack Computers (LRC), or Terminal
Automation System (TAS).
Litres and Litres/Minute are used as the default units throughout this
manual. When other units are programmed in the instrument (such as
Gallons), the units in other programmable and displayed parameters
change accordingly.
An asterisk (*) denotes default options.

Overview
1 - 2 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
Intentionally left blank.

2 - 1 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
CHAPTER 2 PROGRAMMING MODE
Use Programming Mode to configure the instrument.
2.1 Entering and Exiting Programming Mode
☛To enter Programming Mode
1. Do one of the following:
• Hold the '8' key down for five seconds.
After using this method, you cannot alter certain parameters for
W&M.
• Use the switch on the instrument.
On the Model 1010 the switch is located on the right hand side of
the enclosure. This switch may be fitted with a tamper seal for
W&M requirements.
FIGURE 2-1 Model 1010A instrument switch
If the instrument is not idle (for example, the instrument is in use by
an operator, or a vehicle overfill or earth system is connected) it
displays the following:
• In this case, either disconnect the permissives to bring the
instrument to the idle state, or wait until loading is complete and
then enter your password.
If password mode is available the instrument displays the following:
2. Enter a valid setup password.
PASSWORD MODE
NOT AVAILABLE
PASSWORD MODE
NOT AVAILABLE
ENTER PASSWORD (XXXX)
>
ENTER PASSWORD (XXXX)
>

Programming Mode
2 - 2 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
The factory default for this password is 6789 but it may be changed
under the GENERAL SETUP sub-menu of the SYSTEM menu (see
CHAPTER 4).
NOTE: If the setup password is lost, record the four to eight digit hexadecimal
number that is displayed at the password prompt (XXXXXXXX), and then
contact a Honeywell supplier, who will be able to convert this number to the
setup password.
If the password entered matches the setup password programmed in
the instrument, the instrument displays the software version number.
3. Press any key to show the time and date that the application
software was compiled.
4. Press any key to show the Weights & Measures software version.
5. Press any key to advance the display to show the time and date
that the Weights & Measure (W&M) section of the software was
compiled.
6. Press any key.
The instrument displays the Main Menu.
V4-000-1010A-CB-VEO03.000-2594
PRESS ANY KEY
V4-000-1010A-CB-VEO03.000-2594
PRESS ANY KEY
JUN 12 2009, 11:53:36
PRESS ANY KEY
JUN 12 2009, 11:53:36
PRESS ANY KEY
W&M VERSION: 8
PRESS ANY KEY
W&M VERSION: 8
PRESS ANY KEY
W&M LIB: JUN 2 2009, 12:02:01
PRESS ANY KEY
W&M LIB: JUN 2 2009, 12:02:01
PRESS ANY KEY
MAIN MENU
6 - ADDITIVE LINES
7 - RECIPES
1 - DISPLAY CONTRAST
2 - SYSTEM
3 - LOADING ARMS
PRESS ENTER TO SELECT
1 - DISPLAY CONTRAST
MAIN MENU
6 - ADDITIVE LINES
7 - RECIPES
1 - DISPLAY CONTRAST
2 - SYSTEM
3 - LOADING ARMS
PRESS ENTER TO SELECT
1 - DISPLAY CONTRAST

Programming Mode
2 - 3 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
☛To exit Programming Mode, navigate to the main menu and then
press the Cancel key.
The system saves the current setup and returns the instrument to
operating mode.
2.2 Navigating in Programming Mode
☛To scroll down the menu, press the Display key. To scroll up the
menu, press the Arm key.
☛To select the highlighted item, press the Enter key.
☛To select a menu item, press the number of that item.
For example, to select the SYSTEM from the main menu, press ‘2’.
You can move directly to an item in a sub-menu in the same way.
For example, to select GENERAL PURPOSE INPUTS from the
main menu, press ‘23’.
2.3 Entering or Selecting Values in Programming Mode
In programming mode the prompt indicates the type of input that is
required. If a parameter has neither a prompt nor parentheses, the
parameter cannot be altered.
Press the Clear key to correct or clear an entry.
2.4 Exiting the Programming Mode
Before exiting Programming Mode the instrument asks for confirmation
on saving the changed configuration settings.
☛Select YES to save the settings.
Table 2-1:
Prompt Input required Do the following
^ Alphanumeric Use the numeric keys and the Decimal Point key to
enter a Decimal Point.
> Numeric Use the numeric keys and the Decimal Point key to
enter a Decimal Point.
Use the Arm key to change the sign after entering a
number.
( ) Select an option Use the Display key to scroll through the options.
When the required option is highlighted, use the
Enter key to select it.

Programming Mode
2 - 4 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
2.5 Menu System
The Configuration Menu for the 1010 instrument consists of the Main
Menus described in the following table. Each menu is described in detail
in CHAPTER 3 through to CHAPTER 9.
The following diagram shows the detailed menu structure for a four-arm
instrument.
Table 2-2: Menu System
Main Menu Purpose
Display Contrast Configures the display to provide optimum visibility based on
ambient lighting
System Configures the system operating parameters
Loading Arms Configures loading arm details such as arm name and additive
recipe
Metering Lines Configures operating parameters relating to metering lines flow
meters, temperature probes, products and other parameters
Product Streams Configures product streams for different valve settings, no flow
timeout, Deadband, etc
Additive Lines Configures additive injector systems
Recipes Configures recipes such as additive quantities and blend
percentage.
MAIN MENU
6 - ADDITIVE LINES
7 - RECIPES
1 - DISPLAY CONTRAST
2 - SYSTEM
3 - LOADING ARMS
PRESS ENTER TO SELECT
1 - DISPLAY CONTRAST
MAIN MENU
6 - ADDITIVE LINES
7 - RECIPES
1 - DISPLAY CONTRAST
2 - SYSTEM
3 - LOADING ARMS
PRESS ENTER TO SELECT
1 - DISPLAY CONTRAST

Programming Mode
2 - 5 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
MENU
1 - DISPLAY CONTRAST
Display Contrast
2 - SYSTEM
General Setup
Loading Options
General Purpose Inputs
General Purpose Outputs
Configure Deadman
Communications
Configure Messages
Opto Outputs
3 - LOADING ARMS
Configure Arm 1
Configure Arm 2
Configure Arm 3
Configure Arm 4
4 - METERING LINES
Configure Line 1
Configure Line 2
Configure Line 3
Configure Line 4
6 - ADDITIVE LINES
Internal Additive Lines
External Additive Lines
5 - PRODUCT STREAMS
Stream 1
Stream 2
Stream 3
Stream 4
7 - RECIPES
Recipe 1
Recipe 2
:
:
Recipe 16

Programming Mode
2 - 6 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
Intentionally left blank.

3 - 1 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
CHAPTER 3 DISPLAY CONTRAST (1)
3.1 Description
Use the Display Contrast menu to adjust display contrast for obtaining
the best view.
Use the Display key to decrease contrast of the LCD, and the Arm key
to increase it.
Set the display contrast of the instrument to suit an average height
operator.
Press and hold the START key for 10 seconds to set the display to the
factory default value of 32.
Select a value in the following range:
1 – 64 (32*)
DISPLAY CONTRAST 1
ADJUST DISPLAY
CONTRAST: 32
DISPLAY CONTRAST 1
ADJUST DISPLAY
CONTRAST: 32

Display Contrast (1)
3 - 2 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
Intentionally left blank.

4 - 1 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
CHAPTER 4 SYSTEM (2)
Use the System menu to change overall system operating parameters,
such as Language Options, Loading Prompts and Passwords.
The System sub-menus are as follows:
1 - General Setup
Use to select items like language options, system time-outs, personnel,
master and vehicle authorisations. See section 4.2.
2 - Loading Options
Use to set operating prompts and system options. See section 4.3.
3 - General Purpose Inputs
Use to select system permissives against a range of inputs. See section
4.4
4 - General Purpose Outputs
Use to select digital output functions to the general purpose outputs.
See section 4.5.
5 - Configure Deadman
Use to enable the Deadman system and set the applicable Deadman
time-outs. See section 4.6.
6 - Communications
Use to set the system communications parameters. See section 4.7.
7 - Configure Messages
Use to set operator prompts and system messages. Refer Section 4.8.
8 - Opto Outputs
The Opto Outputs sub-menu of the System menu allows the operator to
configure the various opto outputs. refer Section 4.9.
SYSTEM 2
7 - CONFIGURE MESSAGES
8 - OPTO OUTPUTS
1 - DISPLAY CONTRAST
2 - LOADING OPTIONS
3 - GENERAL PURPOSE INPUTS
PRESS ENTER TO SELECT
1 - GENERAL SETUP
SYSTEM 2
7 - CONFIGURE MESSAGES
8 - OPTO OUTPUTS
1 - DISPLAY CONTRAST
2 - LOADING OPTIONS
3 - GENERAL PURPOSE INPUTS
PRESS ENTER TO SELECT
1 - GENERAL SETUP

System (2)
4 - 2 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
4.1 System Menu
2- LOADING OPTIONS
1- GENERAL SETUP
3- GENERAL PURPOSE INPUTS
2- SYSTEMMENU
4-GENERAL PURPOSE OUTPUTS
5- CONFIGURE DEADMAN
7- CONFIGURE MESSAGES
6-COMMUNICATIONS
8- OPTO OUTPUTS
LANGUAGE OPTIONS
ARMS
RIT PANEL
SYSTEM OF UNITS
BATCH TYPE
TRANSACTION NUMBER
CLOCK
AUTHORISATIONS / PINS
TIMEOUTS
BAY NUMBER
PORT 1
PORT 2
PORT 3
TERMINAL AUTOMATION MODE
OPTIONS
INITIAL MESSAGES
MANAGER MESSAGES
DEADMAN MESSAGES
GP INPUT MESSAGES

System (2)
4 - 3 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
4.2 General Setup (21)
The General Setup sub-menu of the System menu covers the selection
of items such as Language Options, Timeouts, Personal, Vehicle
Authorisations and RIT configuration.
4.2.1 Language Options
This Option is not available with the standard CB Application Pack.
Language options not available
4.2.2 Arms
Use the Arms sub-menu to set the first arm number.
First Arm Number When there are multiple instruments in a single bay, consecutive arm
numbers can be assigned across the units to match the numbering of
the physical loading arms.
Enter a value in the following range:
1 to 6 (1*)
4.2.3 Remote Interaction Terminal (RIT) Panel
Use the RIT to operate the instrument without using the keyboard in
stand- alone mode and in load scheduling mode. After enabling RIT, 3
inputs and 3 outputs must be assigned for each arm. Inputs 11 to 16
and outputs 25 to 30 are assigned to RIT by default. The operator can
select the desired inputs and outputs through the general purpose
inputs and outputs menu.
Use this menu enable or disable the RIT PANEL. When the RIT is
enabled, user can set different states for RIT lamp outputs as below.
Select one of the following options:
Enable
Disable*
GENERAL SETUP 21
- TIMEOUTS
- BAY NUMBER
- DISPLAY CONTRAST
- ARMS
- RIT PANEL
PRESS ENTER TO SELECT
- LANGUAGE OPTIONS
GENERAL SETUP 21
- TIMEOUTS
- BAY NUMBER
- DISPLAY CONTRAST
- ARMS
- RIT PANEL
PRESS ENTER TO SELECT
- LANGUAGE OPTIONS

System (2)
4 - 4 Model 1010 Application Pack CB Part No.: 4418024 - Rev. 1
Programming Manual
Constraints: Only available when you use the Weights and Measures
switch on the instrument to enter programming mode.
RIT is available with 1 arm or 2 arm systems only.
LAMP STATUS BOOT No selection possible for BOOT state.
The following lamp status is available for boot condition:
ALL OFF
LAMP STATUS IDLE Allows the operator to select the lamp status for idle.
Select one of the following options:
ALL OFF
RED STEADY*
RED FLASHING
AMBER STEADY
AMBER FLASHING
GREEN STEADY
GREEN FLASHING
LAMP STATUS
AUTHORISATION Allows the operator to select the lamp status for authorization.
Select one of the following options:
ALL OFF
RED STEADY
RED FLASHING
AMBER STEADY*
AMBER FLASHING
GREEN STEADY
GREEN FLASHING
LAMP STATE WAIT ACK Allows the operator to select the lamp status for wait ACK
Select one of the following options:
ALL OFF
RED STEADY
RED FLASHING
AMBER STEADY
AMBER FLASHING*
GREEN STEADY
GREEN FLASHING
LAMP STATE WAIT
START Allows the operator to select the lamp status for wait start
Select one of the following options:
ALL OFF