Honeywell Gent Vigilon Plus User manual

Vigilon Plus
Basic Commissioning Training

Technical Support Helpline
0203 4091779 Option 2
www.gentexpert.co.uk
www.gent.co.uk
E-mail: [e-mail]
Contacts and Resources

Part 1 –Pre-Requisite eLearning
This section of the Vigilon Basic Commissioning Course consists of four
self-paced pre-attendance eLearning modules:
❑VBC Pre-Attendance Module A –Vigilon Panel Hardware.
❑VBC Pre-Attendance Module B –Vigilon Loop Architecture
and the Loop Cards Allocation Process
for both Soft and SAFE Addressed Loops.
❑VBC Pre-Attendance Module C –S-Quad Visual Identifiers, Part
Numbers and Wiring.
S-Cube Visual Identifiers, Part Numbers
and Wiring.
Principles of Dual Angle Optical Sensing.
Loop Breaker and Voltage Status.
Digital and Analogue Channels of Devices.
Vigilon Standard Signals and Voice Alarm
Messages of S-Quad/SCube Devices.
❑VBC Pre-Attendance Module D –Panel Menu navigation, Card Status, Loop Control
and Loop Card Status, Find Device, more detailed
Loop Allocation Process and Loop Map Interpretation
and setting the Panel’s Date and Time.

Vigilon Plus
4 & 6 Loop Panels

Vigilon Plus –Inner Door
Zone LEDs (Zones 1 to 32)
8 Line LCD Display
Full QWERTY Keyboard
Control and Function Buttons
System Indication LEDs
Printer aperture

Vigilon Plus 24 (1-4 loop Control Panel)
2 x 12v 21ah batteries
wired in series
24Hr PSU with
one battery circuit
Mains Supply
Termination
Inner Door
DKC (Display Keyboard Card) Terminal Card
Printer (If fitted)
Backplane

Vigilon Plus 72 (1 to 6 Loop Control Panel)
72 Hrs PSU
Two Battery Circuits
Battery Filter PCB providing
cable terminations to external battery box
PCB
External Battery Box configurations
The configuration to be used will be
determined by the Battery Standby
and Loop Load Calculation.
Lower shelf only populated with
2 x 21Ah SLA battery pairs Both Upper & Lower shelf
Populated with 4 x 21Ah SLA battery pairs

Note:
When Using
4 batteries only
use P1 & P2
12v 12v
12v 12v
12v 12v
Remote battery box
Control panel
3 x 2 core pairs
1.5mm2 –10m maximum
2.5mm2–15m maximum
12v 12v
Vigilon Plus 72 –Battery Box Connections
In-Line Fuse
In-Line Fuse

Backplane and Non-Volatile Memory (Card14)
NVM Protection Link Non-Volatile Memory (NVM)
(Card 14)
Card
Slots
Terminations for cards fitted in Slots P7 & P8
P1
P2
P3
P4
P5
P6
P7
P8

MCC = Main Control Card
KEYBOARD
FIRE & FAULT
LEDs
WARNING,
LC DISPLAY
MCC CARD
LOOP CARD
1
NETWORK CARD or
IO Card (Optional)
F4F3F2
F1
SLOT P1
(Card 0)
SLOT P2
(Card 15)
SLOT P3
(Card 1)
to
PRINTER
Control panel (1–6 loop) Cards
NVM CARD
LOOP CARD
6
Flash Memory = Non Volatile Memory –NVM Card
POWER
SUPPLY
B
A
T
T
E
R
Y
Card 14
SLOT P4
(Card 2)
SLOT P5
(Card 3)
SLOT P6
(Card 4)
SLOT P7
(Card 5)
SLOT P8
(Card 6)

Information held on card:
Panel address
Sector linking
Delay block
Time slot
Zones
Command Builds
Auxiliary relays
Main Control Card (MCC) –Card 0
BATT 3

NO INFORMATION
KEPT ON THIS CARD
Input/Output Card (IOC) –Optional Card for Vigilon Plus 24 or 72
Rotary switch
alters card type
DIL switches all set to ‘up’ (off) position
DKC switches used instead
Software chip 0 Half duplex
1 Slave
2 Remote Printer
3 Universal, half duplex
4 Ascom pager
5 Domain bridge, full duplex
6 Universal, full duplex
This card provides the panel with 1 x RS232 serial Port and 1 x RS485 Port

ON
Switch no.
Baud rate
( 19200 )
EN54 Panels:
Domain address
( eg. 1 )
DKC (Display Keyboard Card)
DIL Switch Setting EN54
DKC
8
7
6
5
4
3
2
1

Loop Processor Card (LPC)
Information kept on card:
(while powered up)
Device labels
Device status
Device states
Loop map
Sectoring
Software version

Vigilon Plus –Terminal Card
Terminations for
Loop 1 to 4
Terminations
for Card 15
(Slot P2)
I/O or
Network Card
2 x 24VDC
Master
Alarms
Circuits
400mA per
Circuit
22KR EOL
Required
per circuit
Master
Alarms
Fuses
Clean
Contacts
(SPCO)
Rated at
1A
24VDC
Auxiliary
Relay 1
DPCO
(Fire)
Rated at
1A 24VDC
Auxiliary
Relay 2
DPCO
(Fault)
Normally
Energised
Rated at
1A 24VDC
Common
0v block
for IOC if
fitted
Ribbon Cable to
the top
connector of the
Backplane
Ribbon Cable to
the top of the
PSU

Compact Plus –2 loops

Compact Plus –Inner Door
Zone LEDs (Zones 1 to 32)
8 Line LCD Display
Full QWERTY Keyboard
Control and Function Buttons
System Indication LEDs

Main Control Board 0
Loop Card 1
Loop Card 2
Network Card 10
NVM Card 14
Compact Plus Cards
Micro SD card

1
11
2 43 65 87 9
12 14
10
13
15
16 17
18
Switch 2 Mode Settings
Posn
0 Final Compact Inner door
(bottom left LED Disablement
2211-148)
1 Compact zonal
(early compact VA only
2211-146)
2Compact first zonal door
(test LED bottom left
2211-136)
3 Compact original door
(No zonal LED’s
2211-127)
4 Final Compact Inner Door Terminal Node
(2211-148)
6 Compact Plus Door
(2211-192)
7 Compact Plus Door (Terminal Node)
(2211-192)
Compact Plus Main Control Board (MCB) –Card
0
19
1 –24VDC Supply & RS485
2 –Port 1 & 2 RS232 Comms Ports
3 –Loop 2 Connections
4 –Aux Relay 1 (Fire) DPCO
5 –Aux Relay 2 (Fault) SPCO
6 –Loop 1 Connections
7 –Monitored I/P (10K EOL)
8 –Clean Contacts (SPCO)
9 –Master Alarms ccts 1 & 2
10 –Master Alarm Fuses
11 –FS3 Protecting 24VDC Supply
12 –Firmware Chip
13 –Mode Switch (SW2)
14 –NVM (Card 14)
15 –NVM Protection Link
16 –USB Comms Port (3)
17 –Processor Reset switch
18 –Lithium Cell (Battery 3)
19 –SD Card slot

230vac Mains
input terminals
FS6
43v 1A FS1
3.15A FS4
24v 1A
Y1 Y2 G1
Batt 1
- +
EEPROM
link (Do Not Remove
Compact Plus PSU