Honeywell 5805 User manual

Models 5805 / 5806
STEEL SECURITY SAFE
Read this manual carefully and never store it inside the safe!

1
Models 5805 / 5806
Steel Security Safe with Digital Lock
PACKAGE CONTENTS
1 – Steel Security Safe
1 – Operation Manual
2 – Override Access Keys
4 – “AA” Batteries
1 – Mounting Kit w/ Bolts
ATTENTION
DO NOT RETURN SAFE TO STORE!
For missing parts or difficulty operating your safe, please contact our Consumer Assistance
Department by telephone.
Store will not accept returned products without prior authorization. You must first contact our
consumer assistance department.
US/Canada 1-877-354-5457 (Toll Free)
Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677
to complete your call. (Toll Free)
Australia 0011-800-5325-7000 (Toll Free)
Germany/New Zealand 00-800-5325-7000 (Toll Free)
Other Countries XX*-310-323-5722
XX*- Dial U.S. Country Code first (Toll Charges Apply)
PRODUCT OVERVIEW
A - LED Display panel
B - Safe Cabinet
C - Safe Door
D - Override Key Lock / Removable Cover
E - Electronic Digital Keypad
F - Safe Serial Number
G - Bottom Panel Pre-drilled Mounting Holes
H - Rear Panel Pre-drilled Mounting Holes

2
SETUP & OPERATION
STEP 1. INSTALL BATTERIES
1. Use the override key to unlock and open the safe.
2. Pull the drawer forward and using a Phillips head screw driver,
remove battery cover located on the inside front panel.
3. Insert (4) “AA” batteries making sure they are installed properly with
regards to (+ -) polarity. (See Diagram).
4. Replace the battery cover and small screw.
5. Do not close the drawer before testing the digital lock.
IMPORTANT NOTE: The batteries provided with the safe are for use during initial programming
and set-up only. They are not for long term use and should be replaced with (4) long lasting
Alkaline or Lithium batteries.
STEP 2. TEST DIGITAL LOCK – FACTORY DEFAULT CODE (159-LOCK)
LOCK SAFE
1. With the drawer open, enter the factory preset pass code: 1-5-9 and press the “LOCK” key.
2. The locking bolts should extend upwards into the locked position and the LED
will display “CLOSED”.
UNLOCK SAFE
1. Enter your new (3-6) digit personal pass code and press the “LOCK” key.
2. The motorized lock will retract the locking bolts into the unlock position and the LED read out
will display “OPENED”
3. Pull the drawer open using the recessed handle located under the digital keypad.
STEP 3. LOCK and UNLOCK SAFE WITH NEW PASS CODE
LOCK SAFE
1. With the safe unlocked, close the drawer.
2. Enter a new personal pass code of your choice (3-6 digits) and press
the “LOCK” key.
3. The motorized lock will extend the locking bolts into the locked
position.
4. The LED will display “CLOSED” for 3 seconds followed by a read out
of the personal code just entered.
5. Make sure you keep a mental or written record of your new code.
UNLOCK SAFE
1. Enter your new (3-6) digit personal pass code and press the “LOCK”
key.
2. The motorized lock will retract the locking bolts into the unlock
position and the LED read out will display “OPENED”
3. Pull the drawer open using the recessed handle located under the
digital keypad.
NOTE: The lock design allows for a new user code each time that the safe is locked
PRIVACY MODE
Normal operation will display your pass code on the LED Display as you enter it into the safe. If you
would like to keep your personal code private, press the “CLEAR” button prior to entering your
code. This will prevent the code from being displayed and must be repeated every time you enter
your code if you want to keep it private.
KEYPAD ALERT TONE
To verify entry of the pass code into memory using the keypad, a “Beep” will be heard after each
entry. This feature may be turned off by pressing the “CLEAR” button twice and reactivated by
repeating the process.

3
ENTERING THE WRONG CODE
If while entering your pass code you press an incorrect key,
push the “CLEAR” button one time and it will erase the
error. You can then re-enter the correct code. If you enter
an incorrect pass code followed by “LOCK”, the safe will
not open and the LED panel will display ”E-COdE”. You
should now re-enter the correct pass code to open the safe.
SECURE LOCKOUT PERIOD
Accidently entering a wrong code is normal and nothing to
worry about. However, for security reasons, if the wrong
code is entered 3 times in a row, then the safe will
automatically begin a five-minute lockout period. During this
time, the LED will display “HOLD05” and the keypad will
become disabled. Entry can only be made during the
lockout by using the Override Access Key. Once the lockout
period has expired, the safe can be opened using the
correct pass code or if necessary, a new code
programmed.
OVERRIDE ACCESS KEY
This safe includes a set of Override Access Keys. In the event your safe will not open because of
weak batteries or a problem with the current pass code, then it can be opened with the override
key. The override lock is located below the keypad. Remove the lock cover and insert the
special key to open. You can now replace the batteries or re-program your code. IMPORTANT:
Override keys should always be kept in a secure location away from the safe and never placed in
the safe.
REPLACING BATTERIES
The current condition of the batteries can be checked at any time by pressing the “LOCK” button
one time. The LED panel will display one of the following messages:
Battery power is good
Battery power is low and all batteries should be replaced
immediately
Replacing the batteries is outlined in Step 1 –INSTALL BATTERIES. Remember to always use
Alkaline or Lithium replacement batteries and avoid using non-alkaline or rechargeable batteries. If
the safe is going to be unused for an extended time period, then the batteries should first be
removed. Properly discard used batteries.
NOTE: Your pass code will remain programmed into memory during battery replacement or when
batteries become weak and inoperable. It will not be erased or changed until you choose to do so.
IF YOU FORGET PASSCODE
1. Insert the Override Access Key into the lock and turn right to the open position.
2. With the key in the open position, press “CLEAR” button on the keypad.
3. Turn the key left to the lock position and remove from the lock.
4. Enter a new (3-6) digit pass code followed by “LOCK”.
5. Your new code is set and you can return to normal operation.

4
ORDERING NEW / REPLACEMENT KEYS
The following information is required to order keys:
1. PROOF OF OWNERSHIP (1 of 2 Options Below)
SALES RECEIPT & IDENTIFICATION – INTERNATIONAL ORDERS ONLY!
•Copy of sales receipt showing Store, Date & Product Description.
•Copy of your picture I.D. (Drivers license, passport, regular I.D.).
PRODUCT OWNERSHIP VERIFICATION FORM
If sales receipt is not available, contact us by email or telephone to request
a “Product Ownership Verification Form”.
2. ORDER INFORMATION
CONTACT INFORMATION
•Name & Shipping Address
•E-mail address (If Available)
•Telephone Number
•Best Time to Contact You
PRODUCT INFORMATION
•Safe Model #
•Safe Serial #
•Lock Key #
•Quantity of Keys Ordered
3. METHOD OF PAYMENT
•Telephone:
Visa or MasterCard
•Mail:
Check or Money Order
NOTE: For pricing please contact Consumer Assistance.
Contact information is located on the back cover of this manual
Terms subject to change without prior notification.
LOCATING SAFE IDENTIFICATION NUMBERS
SERIAL NUMBER
Located on lower right corner on front of
safe. Do Not Remove Safe I.D. Tags!
KEY NUMBER
4 Digit Number etched on the metal collar
located around the key hole.

5
MOUNTING KIT
For extra security, you may want to permanently secure your safe to the floor. Pre-drilled holes for
this purpose are located on the bottom of the safe. While it is not extremely difficult to mount the
safe, it is important that you have the proper tools and knowledge to do so. If not, then you might
choose to utilize the services of a professional.
1. Unlock the safe and Pull the drawer out until it stops. On each of the drawer glides there is
a small plastic latch. To remove the drawer you need to simultaneously push down on the
right side latch while pulling up on the left side latch putting forward pressure on the
drawer as you do. This will release the drawer from the drawer glides and allow the drawer
to be removed.
2. Select a suitable and convenient location.
3. If safe is being mounted to a wood floor, then it can be secured using at least two or more
of the bottom pre-drilled holes. Lag screws and washers should be used to secure in
place.
4. If safe is being mounted to a concrete slab, then after determining placement, mark the
hole positions and set the safe aside. A mortar bit will be required to drill holes into the
concrete and masonry anchors used to secure in place.
5. Once safe is properly mounted, replace the drawer by positioning back onto the drawer
slides and closing.
It is important to note that if prior to installation you have any questions and/or concerns regarding
the proper securing of the safe to a wall or floor you should check with your local home center /
hardware retailer or independent contractor. The securing of the safe to a wall or floor is at the
consumer’s expense and discretion. LHLP, Inc. is not responsible for any costs incurred if the unit is
damaged and needs to be replaced.

6
LIMITED WARRANTY
LH Licensed Products, Inc., (“LHLP, Inc.”) warrants that for a period of seven (7) years
from the date of purchase, this product will be free from structural or mechanical
defects resulting from materials or workmanship. LHLP, Inc., at its sole option and as
the purchaser’s sole remedy under this warranty, will repair or replace this product or
any component of the product found to be defective during the warranty period.
Replacement or repair will be made with a new or remanufactured product or
component. If the product is no longer available, replacement may be made with a
similar product of equal or greater value.
THIS IS YOUR EXCLUSIVE WARRANTY.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
This warranty is only valid for the original retail purchaser from the date of initial retail
purchase and is not transferable. You must keep the original sales receipt. Proof of
purchase is required to obtain warranty service.
LHLP, Inc. dealers, service centers, or retail stores selling this product do not have the
right to alter, modify or in any way change the terms and conditions of this warranty.
This warranty does not apply to the finish on the product. This warranty does not cover
normal wear and tear of parts or damage resulting from any of the following: negligent
use or misuse of the product, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than LHLP, Inc. or an authorized service center,
improper installation, or exposure to extremes of heat or humidity. Further, the
warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes.
LHLP, Inc. shall not be liable for any incidental or consequential damages caused by
the breach of any express or implied warranty or otherwise relating to the sale of this
product. LHLP, Inc. is also not responsible for: costs associated with removing or
installing the product; damage or loss of the contents of the product; nor for the
unauthorized removal of the contents; or damages incurred during shipment.
THE ABOVE WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, AND LHLP, INC. DISCLAIMS ANY AND ALL OTHER
COVENANTS AND WARRANTIES.
Except to the extent prohibited by applicable law, any implied warranty of
merchantability or fitness for a particular purpose is limited in duration to the duration
of the above warranty period. Some states, provinces or jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above limitations or exclusion may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state, or province to province, or jurisdiction to jurisdiction.

7
CONSUMER ASSISTANCE
EMAIL (Best Contact
Method):
[email protected]
WEBSITE:
www.Honeywellsafes.com
ADDRESS:
Consumer Assistance Dept.
LH Licensed Products, Inc.
860 East Sandhill Avenue
Carson, CA 90746 USA
TELEPHONE:
US/Canada 1-877-354-5457 (Toll Free)
Mexico 01-800-288-2872 After English voice recording stops you
must then enter 800-860-1677 to complete your call. (Toll Free)
Austrailia 0011-800-5325-7000 (Toll Free)
Germany/New Zealand 00-800-5325-7000 (Toll Free)
Other Countries XX*-310-323-5722 (Toll Charges Apply)
XX*- Dial U.S. Country Code first
CALL CENTER HOURS:
US/Canada 7am – 5pm (PST**) Mon – Fri
CALL BACK HOURS:
Other Countries 7am – 8pm (PST**) Mon – Fri
PST**- Local time in Los Angeles, CA, USA
INTERNATIONAL CALL BACK HOURS:
If you need to speak with a consumer assistant and cannot contact us during the Call
Center hours above, please send an email or leave a telephone message, including your
Name, Telephone Number and the best time for us to contact you during the Call Back hours
above and we will make our best effort to contact you and help to answer any of your
questions or concerns.
The Honeywell Trademark is Used under license from Honeywell
International Inc. Honeywell International Inc. makes no representations
or warranties with respect to this product.
Manufactured by
LH Licensed Products, Inc.
860 East Sandhill Avenue
Carson, CA 90746
M5805E11112015