Honeywell ADEMCO 5805-6 User manual

ADEMCO 5805-6
Wireless Key Transmitter
USER GUIDE
GENERAL INFORMATION
The 5805-6 is a compact, 6-button portable
wireless transmitter that permits an alarm
system to be controlled remotely. The transmitter
is typically used for arming, disarming, panic and
output relay operation. Check with your installer
for operation of the buttons on your unit.
OPERATING THE BUTTONS
To activate a programmed function, press and
hold the associated button(s) down. The LED will
flash green to indicate the unit has transmitted
in Standard mode, or red to indicate it has
transmitted in High-Security mode.
In order to minimize the possibility of
accidental transmissions, the buttons on the
5805-6 must be pressed and held for at least
1/2 second to activate the transmitter.
Figure 1 - 5805-6 Transmitter
Table 1 - Transmitter Functions
(Complete this table with your installer)
Button Function
ON
OFF
1
2
3
4
ON + 4
3 + 4
LOW BATTERY INDICATION
When a Button is pressed and a Low Battery
condition exists, a message is transmitted to the
control panel and LOW BAT will be displayed on
the keypad. The LED will not flash during
transmission if the battery is low.
REPLACING THE BATTERY
Removing the battery
1. Remove the case back by using the blade of a
small screwdriver to pry it open.
2. Insert the blade of a small screwdriver as
shown in Figure 2.
3. Twist the screwdriver to release the battery.
4. Carefully remove the battery.
5805-010-V0
BATTERY
(+)
INSERT
SCREWDRIVER
BLADE HERE
Figure 2 – Removing the Battery
!
Do not remove the printed circuit board.
(Continued on reverse)

Installing a new battery
Before installing a new battery, Press and
hold any button for at least two seconds
1. Insert a new battery in case back location as
shown in Figure 3. Positive (+) end must
face up. Use Panasonic CR2032, Maxell
CR2032, Duracell DL 20325, or Varta CR2032
lithium battery only.
!
Improper installation will result in
damage to the battery.
2. Close the case by snapping case front and
back together.
3. Press any button and verify that the LED
flashes.
NOTE
POSITIVE (+) SIDE
MUST FACE UP
5805-008-V2
INSERT THIS
END FIRST
BATTERY
(+)
INSTALL UNDER THIS TAB
AND ATOP THIS TAB
Figure 3 - Installing the Battery
LIMITATIONS STATEMENT
Signals sent by wireless transmitters may be blocked or reflected by metal objects before they reach the alarm
receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object
somehow blocks the signal path.
Wireless button type transmitters that have visual and audible indications of status must be used to confirm that
the desired action (such as arming) has occurred after pressing a function button on any of these transmitters. Be
sure to listen for appropriate audible and visual indications that such action has occurred. Otherwise, you could
inadvertently leave yourself or your premises unprotected.
External factors such as humidity, high or low temperatures, or constant activation of a programmed button may
reduce battery life in a given installation. If the button unit is used infrequently, activate it regularly (once per
week) to confirm operation. A button type transmitter will report a low battery condition to the alarm control when
a low battery status is detected.
FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM,
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL WITH WHICH THIS DEVICE IS USED.
FCC AND INDUSTRY CANADA STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES and RSS210 OF INDUSTRY CANADA. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
165 Eileen Way, Syosset, New York 11791
Copyright © 2006 Honeywell International Inc.
www.honeywell.com/security
‡K5761V2XŠ
K5761V2 7/06 Rev. A