Honeywell SMV800 User manual

Honeywell Process Solutions
SMV800 Series HART/DE Option
User’s Manual
34-SM-25-06
Revision 6.0
July 2019

Page ii SMV800 Series HART/DE Option User’s Manual Revision 6.0
Copyrights, Notices and Trademarks
© Copyright 2019 by Honeywell, Inc.
Revision 6, July 2019
While the information in this document is presented in good faith and believed to be
accurate, Honeywell disclaims any implied warranties of merchantability and fitness for a
particular purpose and makes no express warranties except as may be stated in the written
agreement with and for its customers. In no event is Honeywell liable to anyone for any
indirect, special, or consequential damages. The information and specifications in this
document are subject to change without notice.
Honeywell, TDC 3000, SFC, SmartLine, PlantScape, Experion PKS, MCT202, MCT404
and TotalPlant are registered trademarks of Honeywell International Inc. Other brand or
product names and service marks are the property of their respective owners.
Honeywell Process Solutions
1860 Rose Garden Lane
Phoenix, AZ 85027

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page iii
About This Manual
This manual provides the details of programming Honeywell SMV800 SmartLine Multivariable
Transmitters for applications involving HART and Digitally Enhanced (DE) communication
protocols. For installation, wiring, and maintenance information refer to the SMV800 SmartLine
Multivariable Transmitter User Manual, document number 34-SM-25-03.
The configuration of your Transmitter depends on the mode of operation and the options selected
for it with respect to operating controls, displays and mechanical installation. Details for
operations involving the Honeywell Multi-Communication (MC) Tookit (MCT404) and
SmartLine Configuration tool (SCT3000) are provided only to the extent necessary to accomplish
the tasks-at-hand. Refer to the associated
The SMV800 SmartLine Multivariable transmitter can be digitally integrated with one of two
systems:
Experion PKS: you will need to supplement the information in this document with the data and
procedures in the Experion Knowledge Builder.
Honeywell’s TotalPlant Solutions (TPS): you will need to supplement the information in this
document with the data in the PM/APM SmartLine Transmitter Integration Manual, which is
supplied with the TDC 3000 book set. (TPS is the evolution of the TDC 3000).
Release Information
SMV800 Series HART /DE Option User Manual, Document # 34-SM-25-06 (this document)
Rev. 1.0, October 2015 First Release (RQUP)
Rev. 2.0, December 2015 Prod release
Rev. 3.0, September 2016 Algorithm option updates
Rev. 4.0, December 2017 Totalizer functionality added (R120)
Rev. 5.0 March 2019 ` (R200)
Rev. 6.0 July 2019 DTM /DD structure update
References
The following list identifies publications that may contain information relevant to the information
in this document.
SMV800 SmartLine Multivariable Transmitter Quick Start Installation Guide, # 34-SM-25-04
SMV800 SmartLine Multivariable Transmitter Safety Manual w/ HART, 34-SM-25-05
SMV800 SmartLine Multivariable Transmitter User Manual, # 34-SM-25-03
MC Tookit User Manual (MCT404), Document # 34-ST-25-50
SCT3000, SmartLine Configuration Tool guide, Document # 34-ST-10-08
PM/APM SmartLine Transmitter Integration Manual, # PM 12-410
SMV800 Series Multivariable, Analog, HART Communications form, Drawing #50049892
Smart Field Communicator Model STS 103 Operating Guide, Document # 34-ST-11-14

Page iv SMV800 Series HART/DE Option User’s Manual Revision 6.0
Patent Notice
The Honeywell SMV800 SmartLine Multivariable Transmitter family is covered by one or more of
the following U. S. Patents: 5,485,753; 5,811,690; 6,041,659; 6,055,633; 7,786,878; 8,073,098; and
other patents pending.
Support and Contact Information
For Europe, Asia Pacific, North and South America contact details, see back page or refer to the
appropriate Honeywell Solution Support web site:
Honeywell Corporate www.honeywellprocess.com
Honeywell Process Solutions https://www.honeywellprocess.com/smart-multivariable-transmitters
Training Classes http://www.honeywellprocess.com/en-US/training
Telephone and Email Contacts
Area
Organization
Phone Number
United States and
Canada
Honeywell Inc.
1-800-343-0228 Customer Service
1-800-423-9883 Global Technical Support
Global Email
Support
Honeywell Process
Solutions
[e-mail]

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page v
Contents
1SMV800 Physical and Functional Characteristics .........................................................................1
1.1 Overview ................................................................................................................................1
1.2 Features and Options..............................................................................................................1
1.2.1 Physical Characteristics..................................................................................................2
1.2.2 Functional Characteristics ..............................................................................................3
1.3 Series, Model Series, Model and Number..............................................................................3
1.4 Safety Certification Information.............................................................................................4
1.5 Transmitter Adjustments........................................................................................................4
1.6 Local Display Options............................................................................................................5
1.7 Optional 3-Button Assembly..................................................................................................5
1.8 Universal Temperature Sensor Option Licensing ..................................................................6
2Communication Modes ..................................................................................................................7
2.1 Overview ................................................................................................................................7
2.2 DE Mode Communication......................................................................................................7
2.3 HART Mode Communication................................................................................................9
3Configuration Tools and Interfaces..............................................................................................11
3.1 Overview ..............................................................................................................................11
3.2 Pre-requisites........................................................................................................................11
3.3 Application Design, Installation, Startup, and Operation.....................................................11
3.3.1 Organization.................................................................................................................11
3.4 Toolkit Participation.............................................................................................................12
3.4.2 Toolkit Software Applications......................................................................................12
3.4.3 Configuration Databases ..............................................................................................12
3.4.4 Configuration................................................................................................................12
3.4.5 MC Toolkit–Transmitter Electrical/Signal Connections..............................................13
3.5 SmartLine Configuration Toolkit (SCT 3000).....................................................................14
3.5.6 SmartLine Configuration Toolkit for use with DE models ..........................................14
3.6 Considerations for SCT 3000...............................................................................................15
3.6.7 SCT 3000 Requirements...............................................................................................15
4Setting up Communications with the SCT3000...........................................................................16
4.1 Establishing Communications..............................................................................................16
4.1.1 Off-line Versus On-line SMV Configuration...............................................................16
4.1.2 Off-line Configuration Procedures...............................................................................16
4.1.3 SCT Hardware Connections.........................................................................................16
4.1.4 SCT 3000 On-line Connections to the SMV................................................................17
4.1.5 Establishing On-line Communications with the SMV .................................................18
4.1.6 Checking Communication Mode and Firmware Version.............................................19
4.1.7 DE Communication......................................................................................................19
4.1.8 Changing Communication Mode..................................................................................19
5DE Transmitter Configuration......................................................................................................20
5.1 Configuration Personnel Requirements................................................................................20
5.2 Configuration using the SCT3000........................................................................................20
5.2.1 SCT On-line Help and User Manuals...........................................................................20
5.3 About Configuration.............................................................................................................20
5.3.2 Configuration Summary...............................................................................................21
5.4 Using the SCT for SMV800 Configuration..........................................................................22

Page vi SMV800 Series HART/DE Option User’s Manual Revision 6.0
5.5 Device Configuration........................................................................................................... 23
5.5.3 Transmitter Tag Name and PV1 Priority..................................................................... 23
5.5.4 General Configuration.................................................................................................. 23
5.5.5 DPConf Configuration - PV1....................................................................................... 25
5.5.6 SP Conf Configuration - PV2 .................................................................................... 29
5.5.7 TempConf Configuration - PV3 ................................................................................ 31
5.5.8 FlowConf Configuration - PV4 ................................................................................. 36
5.5.9 Using Custom Engineering Units ................................................................................ 40
5.5.10 Flow Compensation Wizard (DE only)........................................................................ 41
5.6 Using the SCT3000 Tool to Configure Local Display Screens on SMV800....................... 43
5.6.11 Display Screen Configuration Instructions.................................................................. 43
5.6.12 Display Screen Configuration Parameters:.................................................................. 48
5.6.13 Saving, Downloading and Printing a Configuration File............................................. 51
5.6.14 Verifying Flow Configuration ..................................................................................... 51
6HART Transmitter Configuration................................................................................................ 52
6.1 Overview.............................................................................................................................. 52
6.1.1 Personnel Requirements............................................................................................... 52
6.2 Overview of FDC Homepage .............................................................................................. 53
6.2.2 Settings......................................................................................................................... 54
6.2.3 Manage DDs ................................................................................................................ 55
6.2.4 Online configuration.................................................................................................... 57
6.2.5 Offline configuration.................................................................................................... 57
6.2.6 Online Configuration Overview................................................................................... 57
6.2.7 Overview of Device Homepage................................................................................... 58
6.2.8 Tabs on the Device Home page ................................................................................... 58
6.2.9 Using FDC for various device operations.................................................................... 60
6.2.10 Procedure to Enter the Transmitter Tag..................................................................... 121
6.2.11 Selecting Variable units of measurement................................................................... 121
6.2.12 Selecting Pressure Units............................................................................................. 123
6.2.13 Selecting Temperature Units...................................................................................... 123
6.2.14 Selecting Flow Units.................................................................................................. 124
6.2.15 Setting PV URV, and LRV Range Values (for Differential Pressure values) ........... 124
6.2.16 Setting Range Values for Applied Pressure for DP................................................... 125
6.2.17 Setting URV, and LRV Range Values (for Static Pressure Values).......................... 126
6.2.18 Setting Range Values for Applied Static Pressure..................................................... 126
6.2.19 Setting URV, and LRV Range Values (for Temperature Values)............................. 127
6.2.20 Setting Range Values for Applied Temperature........................................................ 127
6.2.21 Entering URV, and LRV Range Values (for Flow Values)....................................... 128
6.2.22 Saving device history................................................................................................. 128
6.2.23 Exporting device history records to FDM.................................................................. 129
6.2.24 Exporting device history records to DocuMint.......................................................... 130
6.2.25 Custom Views............................................................................................................ 130
6.2.26 Offline Configuration................................................................................................. 132
7DE Calibration........................................................................................................................... 135
7.1 Overview............................................................................................................................ 135
7.2 Calibration Recommendations........................................................................................... 135
7.3 Test Equipment Required for Calibration.......................................................................... 135
7.4 DE Output Calibration....................................................................................................... 136
7.4.1 Output Calibration Preparation.................................................................................. 136
7.4.2 Output Calibration using SCT3000............................................................................ 137

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page vii
7.5 Calibrating Range Using a Configuration Tool..................................................................139
7.5.3 Conditions for Input Calibration.................................................................................139
7.5.4 Input Calibration Procedures Description ..................................................................139
7.6 DE Input Calibration Procedure.........................................................................................140
7.6.5 DP Input Cal...............................................................................................................140
7.6.6 Correct DP Input at the Lower Range Value (LRV)..................................................141
7.6.7 Correct DP Input at URV...........................................................................................143
7.6.8 AP Input Calibration...................................................................................................145
7.6.9 AP Input Cal LRV (Lower Range Value) Correct_...................................................145
7.6.10 AP Input Cal URV (Upper Range Value) Correct .....................................................146
7.6.11 Reset Corrects.............................................................................................................146
7.6.12 Temperature Input Calibration ...................................................................................147
7.6.13 Process Temperature LRV (Lower Range Value) Correct_.......................................147
7.6.14 Process Temperature URV (Upper Range Value) Correct.........................................148
7.6.15 Reset Corrects.............................................................................................................148
8HART Calibration......................................................................................................................149
8.1 About This Section.............................................................................................................149
8.1.1 About Calibration.......................................................................................................149
8.1.2 Equipment Required...................................................................................................149
8.2 Analog Output Signal Calibration......................................................................................150
8.3 Calibrating Range...............................................................................................................151
8.3.3 Correcting the Lower Range Value (LRV) for Differential pressure.........................151
8.3.4 Correcting the Upper Range Value (URV) for Differential Pressure.........................151
8.3.5 Resetting Calibration for Differential Pressure ..........................................................153
8.3.6 Correcting the Lower Range Value (LRV) for Temperature .....................................153
8.3.7 Correcting the Lower Range Value (URV) for Temperature.....................................154
8.3.8 Resetting Calibration for Temperature.......................................................................155
8.3.9 Calibration Records....................................................................................................155
8.3.10 Dual / Triple Calibration ............................................................................................156
9HART Advanced Diagnostics....................................................................................................157
9.1 About This Section.............................................................................................................157
9.2 Advanced Diagnostics........................................................................................................157
10 Troubleshooting and Maintenance .........................................................................................158
10.1 Troubleshooting Using the SCT.........................................................................................158
11 Using DTMs...........................................................................................................................159
11.1 Introduction........................................................................................................................159
11.2 Components........................................................................................................................159
11.3 Downloads..........................................................................................................................159
11.4 Procedure to Install and Run the DTM...............................................................................159
11.5 SMV800 Online Parameterization......................................................................................160
11.5.1 Configuration Menu:..................................................................................................160
11.5.2 Monitoring Menu: ......................................................................................................161
11.5.3 Diagnostics Menu :.....................................................................................................161
11.5.4 Maintenance Menu:....................................................................................................162
11.6 Advanced Flow Setup (for DTM only) ..............................................................................163
11.6.5 Engineering Units.......................................................................................................163
11.6.6 Flow Calculation Setup ..............................................................................................166
11.6.7 Fluid Data Screen.......................................................................................................175
11.6.8 Coefficients and switches Screen...............................................................................183
11.6.9 Element Specific Properties screen ............................................................................192
11.7 Saving the current Online Configuration as Offline dataset...............................................198
11.8 SMV800 Offline Parameterization.....................................................................................199

Page viii SMV800 Series HART/DE Option User’s Manual Revision 6.0
12 Comparison of configuration options from DD host vs DTM.............................................. 200
13 Flow Engineering Units Configuration for SMV800 HART and DE.................................... 201
13.1 SMV800 HART configuration using Pactware:................................................................ 201
13.1.1 For Standard Flow Condition (Temperature: 15 °C, Pressure: 1.01325 barA):......... 201
13.1.2 For Normal Flow Condition (Temperature: 0 °C, Pressure: 1.01325 barA):............. 203
13.2 SMV800 DE Configuration using SCT3000..................................................................... 204
13.2.3 For Standard Flow Condition (Temperature: 15 °C, Pressure: 1.01325 barA):......... 204
13.2.4 For Normal Flow Condition (Temperature: 0 °C, Pressure: 1.01325 barA):............. 204
13.3 User defined Custom Units selection on SMV 800 DE Model.......................................... 205
14 Example Configuration of Flow for below specification:...................................................... 207
15 HART DD binary file format compatibility matrix............................................................... 215
16 Security.................................................................................................................................. 216
16.1 How to report a security vulnerability ............................................................................... 216
17 Troubleshooting..................................................................................................................... 217
17.1 Diagnostic Messages for DE transmitters.......................................................................... 217
17.2 HART Diagnostic Messages.............................................................................................. 232
17.3 Flow Configuration Diagnostics, Messages and Values.................................................... 252
Appendix A........................................................................................................................................ 257
Glossary............................................................................................................................................. 289

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page ix
List of Figures
Figure 1 –SMV800 Major Assemblies..................................................................................................2
Figure 2 –Electronics Housing Components.........................................................................................2
Figure 3 –Typical Name Plate Information............................................................................................3
Figure 4 –DE Communication through SCT.........................................................................................7
Figure 5 –DE Mode Value Scaling .......................................................................................................8
Figure 6 –HART Point-to-Point and Multi-drop Value Scaling ...........................................................9
Figure 7 –MC Toolkit-Transmitter Electrical/Signal Connections.....................................................13
Figure 8 - SmartLine Configuration Tool ............................................................................................14
Figure 9 - SCT Hardware Components................................................................................................16
Figure 10 - SMV On-line Configuration Process.................................................................................21
Figure 11 - Square Root Dropout Points for PV 1 ...............................................................................28
Figure 12 –RTD Range Configuration................................................................................................34
Figure 13 - Current Range Settings......................................................................................................35
Figure 14 - Typical Volumetric Flow Range Setting Values...............................................................38
Figure 15 - Low Flow Cutoff...............................................................................................................39
Figure 16 –FDC Homepage.................................................................................................................53
Figure 17 –Device Homepage.............................................................................................................58
Figure 18 –Output Calibration Test Connections..............................................................................136
Figure 19 –DE Analog Mode Scaling and Test Connections............................................................137
Figure 20 –Input Calibration Connections ........................................................................................140
Figure 21 - Setup to manually set the PV LRV and URV..................................................................152
Figure 22 - Typical Volumetric Flow Range Setting Values.............................................................196
Figure 23 –Low Flow cutoff action...................................................................................................197
Figure 24 - Engineering unitsTab.......................................................................................................211
Figure 25- Flow calculation setup tab................................................................................................212
Figure 26 - Coeficients and switches..................................................................................................212
Figure 27 - Simulation tab..................................................................................................................213
Figure 28 - Fluid data.........................................................................................................................213
Figure 29 - Flow calculation setup.....................................................................................................214
Figure 30- Summary page..................................................................................................................214

Page x SMV800 Series HART/DE Option User’s Manual Revision 6.0
List of Tables
Table 1 –Features and Options.............................................................................................................. 1
Table 2 –Available Display Characteristics.......................................................................................... 5
Table 3 –User Manual Related Topics................................................................................................ 11
Table 4 - Making SCT 3000 Hardware Connections........................................................................... 17
Table 5 - Making SCT 3000 On-line Connections.............................................................................. 18
Table 6 - PV Type Selection for SMV Output..................................................................................... 23
Table 7 - SMV Analog Output Selection............................................................................................. 24
Table 8 - Pre-programmed Engineering Units for PV 1...................................................................... 25
Table 9 - Pre-programmed Engineering Units for PV2*..................................................................... 29
Table 10 - Pre-programmed Engineering Units for PV3..................................................................... 31
Table 11 - Sensor Types for PV3 Process Temperature Input............................................................. 32
Table 12- Pre-programmed Volumetric Flow Engineering Units for PV4.......................................... 36
Table 13 - Pre-programmed Mass Flow Engineering Units for PV4................................................... 37
Table 14 - Primary Flow Elements...................................................................................................... 41
Table 15 –Display Screen Configuration Parameters......................................................................... 48
Table 16 - Display Screen configuration parameters details ............................................................... 49
Table 17 - FDC homepage elements.................................................................................................... 53
Table 18 - Device health status............................................................................................................ 58
Table 19 - HART Transmitter Parameters........................................................................................... 62
Table 20 - Configuration Menu ........................................................................................................... 66
Table 21 - Flow Calculation Setup ...................................................................................................... 82
Table 22 - Monitoring Menu.............................................................................................................. 103
Table 23 –Communication module diagnostics................................................................................ 106
Table 24 - Meter Body (MB) diagnostics.......................................................................................... 108
Table 25 - Temperature Module diagnostics ..................................................................................... 110
Table 26 - Write Tx Install date......................................................................................................... 112
Table 27 - Write TM Install date ....................................................................................................... 112
Table 28 - Config History.................................................................................................................. 112
Table 29 - Fault history...................................................................................................................... 112
Table 30 - Maintenance Menu........................................................................................................... 113
Table 31 –Device Status .................................................................................................................... 117
Table 32 –Flow Units........................................................................................................................ 120
Table 33 –Tamper Reporting Logic Implementation with Write Protect......................................... 121
Table 34 –Viewing Advanced Diagnostics....................................................................................... 157
Table 35 - Accessing SMV 800 Diagnostic Information using the SCT........................................... 158
Table 36 –Unit Configuration........................................................................................................... 164
Table 37 –Setup Flow Calculation.................................................................................................... 167
Table 38 - Configuration of Materials, Flowing Temperature and Thermal Expansion Coefficients175
Table 39 –Fluid Data ........................................................................................................................ 176
Table 40 - Coefficients and Switches ................................................................................................ 184
Table 41 - Simulate Process Variables .............................................................................................. 190
Table 42 - Viscosity Coefficients: Dependency to Algorithm option................................................ 190
Table 43 - Density Coefficients: Dependency to Algorithm option .................................................. 191
Table 44 - Element Specific Properties.............................................................................................. 194
Table 45 –Flow Parameters .............................................................................................................. 200
Table 46 –Flow Configuration parameters ....................................................................................... 207
Table 48 - HART DD binary file format compatibility matrix.......................................................... 215
Table 49 - Critical Status Diagnostic Message Table........................................................................ 218
Table 50 - Non-Critical Status Diagnostic Message Table................................................................ 221

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page xi
Table 51 - Communication Status Message Table.............................................................................227
Table 52 - Information Message Table...............................................................................................229
Table 53 - SFC Diagnostic Message Table ...................................................................................230
Table 53 –HART Critical Details......................................................................................................232
Table 54 - Non-Critical 1 Diagnostic Details.....................................................................................239
Table 55 - Non-Critical 2 Diagnostic Details.....................................................................................244
Table 56 - Non-Critical 3 Diagnostic Details.....................................................................................247
Table 57 - Non-Critical 4 Diagnostic Details.....................................................................................251
Table 58 –Extended Device Status Diagnostic Details.....................................................................251
Table 59 - Air Through a Venturi Meter Configuration Example......................................................276
Table 60 - Superheated Steam using an Averaging Pitot Tube Configuration Example ...................277
Table 61 - Liquid Propane Configuration Example ...........................................................................280
Table 62 - Air Configuration Example...............................................................................................283
Table 63 - Superheated Steam Configuration Example .....................................................................286

Page xii SMV800 Series HART/DE Option User’s Manual Revision 6.0
This page has been intentionally left blank

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page 1
1 SMV800 Physical and Functional Characteristics
Overview
This section is an introduction to the physical and functional characteristics of Honeywell’s family of
SMV800 SmartLine Multivariable Transmitters.
Features and Options
The SMV800 SmartLine Multivariable Transmitter type SMV800 HART supports six device
variables: DP (Differential Pressure), SP (Static Pressure), PT (Process Temperature), Flow and MBT
(Meter body Temperature), Totalizer and five dynamic variables: PV (Primary Variable), SV
(Secondary Variable), TV (Tertiary Variable) and QV (Quaternary Variable). Primary variable (PV)
can be configured as DP, SP, PT, Flow and Totalizer. Secondary Variable (SV), Tertiary Variable
(TV), Quaternary Variable (QV) can be configured as DP, SP, PT, Flow, MBT and Totalizer.
The dynamic variables can be set to any of the said device variables. Table 1 lists the protocols,
human interface (HMI), materials, approvals, and mounting bracket options for the SMV800
Transmitter.
Note: SMV800 DE model does not support Totalizer. All the other Device variables and dynamic
variables are supported as in HART model.
Table 1 –Features and Options
Feature/Option
Standard/Available Options
Communication Protocols
HART 7 and Digitally Enhanced (DE)
Human-Machine Interface
(HMI)
Advanced Digital Display
Three-button programming (optional)
Advanced display languages: English, German, French, Italian,
Spanish, Russian, Turkish, Chinese & Japanese
Calibration
Single, Dual and Triple Cal for PV1 (Diff.Pressure) and PV2 (Static
Pressure)
Approvals (See Appendix C
for details.)
ATEX, CSA, FM, IECEx, NEPSI
Mounting Brackets
Angle/flat carbon steel/304 stainless steel, Marine 304 stainless
steel
Integration Tools
Experion

Page 2 SMV800 Series HART/DE Option User’s Manual Revision 6.0
Physical Characteristics
As shown in
Figure 1, the SMV800 is packaged in two major assemblies: the Electronics Housing and the Meter
Body. The elements in the Electronic Housing respond to setup commands and execute the software
and protocol for the different pressure measurement types: DP (Differential Pressure), SP (Static
Pressure), PT (Process Temperature) and MBT (Meter body Temperature).
The Meter Body provides connection to a process system. Several physical interface configurations
are available, as determined by the mounting and mechanical connections. Refer to the SMV800
SmartLine User’s manual, document #34-SM-25-03 for installation and wiring details.
Figure 1 –SMV800 Major Assemblies
Figure 2 –Electronics Housing Components

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page 3
Functional Characteristics
The SMV800 SmartLine Multivariable transmitter measures Differential Pressure, Static Pressure
(Absolute or Gauge), and Process Temperature. These measurements are used to calculate volumetric
or mass flow rates. The measured values and calculated flow may be read by a connected Host.
Available communications protocols include Honeywell Digitally Enhanced (DE) and HART. Output
options include Digital and 4-20 mA Analog.
The SMV800 measures Process Temperature from an external RTD or Thermocouple.
The device may be configured to map any of the five Process Variable to the Analog Output (4-20
mA):
Differential Pressure PV1
Static Pressure PV2
Process Temperature PV3
Calculated Flow Rate PV4
Calculated Totalizer PV6
An optional 3-button assembly is available to set up and configure the transmitter via the Display. In
addition, a Honeywell MCT404/MCT202 Toolkit is available for configuration of HART models.
The SCT SmartLine Configuration Tool (not supplied with the Transmitter) can facilitate setup and
configuration for DE devices.
Certain adjustments can be made through an Experion Station or a Universal Station if the
Transmitter is digitally integrated with Honeywell’s Experion or TPS/TDC 3000 control system.
Series, Model Series, Model and Number
The Transmitter nameplate mounted on the top of the Electronics Housing (see
Figure 2) lists the model number, physical configuration, electronics options, accessories,
certifications, and manufacturing specialties.
Figure 3 is an example of a typical SMV800 Transmitter name plate.
The model number format consists of a Key Number with several table selections.
Figure 3 –Typical Name Plate Information

Page 4 SMV800 Series HART/DE Option User’s Manual Revision 6.0
You can readily identify the series and basic Transmitter type from the third and fourth digits in the
key number. The letter in the third digit represents one of these basic measurement types for the Static
Pressure:
A = Absolute Pressure
G = Gauge Pressure
E.g. SMA810, SMA845 or SMG870
For a complete selection breakdown, refer to the appropriate Specification and Model Selection
Guide provided as a separate document.
Safety Certification Information
An “approvals” name plate is located on the bottom of the Electronics Assembly; see
Figure 1 for exact location. The approvals name plate contains information and service marks that
disclose the Transmitter compliance information. Refer to Appendix C of the SMV800 SmartLine
Transmitters User’s manual, document number 34-SM-25-03 for details.
Transmitter Adjustments
Zero and Span adjustments are possible in new generation SMV800 SmartLine Multivariable
Transmitters by using the optional three-button assembly located at the top of the Electronic Housing
(see
Figure 2). However, certain capabilities are limited in the following configurations:
1. Without a display –Zero and Span setting only for HART and DE devices.
oZero/Span button option works for DP, SP and PT when the same is mapped to
analog output accordingly. For example:
-If DP is mapped to AO, Zero/Span buttons options applied on DP.
-If SP is mapped to AO, Zero/Span buttons options applied on SP.
-If PT is mapped to AO, Zero/Span buttons options applied on PT.
-If Flow is mapped to AO, Zero button will perform DP zero correct operation*.
And for Span button it will not perform any operation
2. With a display –Complete Transmitter configuration is possible for HART and DE
devices.
* This feature is only available in HART R120 device.
You can also use the Honeywell MCT404 Configuration Tool –FDC application to make any
adjustments to an SMV800 Transmitter with HART.
For DE models the SCT3000 PC tool application can be used to configure the device.
Certain adjustments can also be made through the Experion or Universal Station if the Transmitter is
digitally integrated with a Honeywell Experion or TPS system.
SMV800 HART models can be configured using Honeywell tools such as Experion in conjunction
with FDM, using DTMs running in FDM or Pactware, or Emerson 375 or 475.

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page 5
Local Display Options
The SMV800 Multivariable Transmitter has an Advanced display; see Table 2.
Table 2 –Available Display Characteristics
Advanced
Display
Screen Format
oLarge process variable (PV)
oPV with bar graph
oPV with trend (1-24 hours, configurable)
PV Selection
Display Units
Decimals
PV Scaling
Scaling Low
Scaling High
Display Low Limit
Display High Limit
Scaling Unit
Screen Custom Tag
Trend Duration (h)
Language
oEN, FR, GE, SP, RU, IT & TU
oEN, CH (Kanji), JP
PV Rotation,
Sequence Time (sec)
Optional 3-Button Assembly
The optional 3-button assembly provides the following features:
Opportunity for immediate reaction with minimal disruptions
Improved maintenance time
Potential savings on hand-held units
Suitable for all environments: hermetically sealed for long life in harsh environments
Suitable for use in all electrical classifications (flameproof, dustproof, and intrinsically safe)
The 3-button assembly is externally accessible and provides the following capabilities:
Menu-driven configuration with optional display:
oUsing increment, decrement & enter keys
oA comprehensive on screen menu guides the way
oConfigure the transmitter
oConfigure the display
oSet zero and span
Zero and span settings without optional display

Page 6 SMV800 Series HART/DE Option User’s Manual Revision 6.0
Universal Temperature Sensor Option Licensing
In a standard device, only RTD Temperature sensor types may be used for measuring Process
Temperature.
The Universal Temperature Sensor option can be enabled after the transmitter is shipped by
purchasing and activating a license, to expand the selection of temperature sensor types to include
thermocouples.
For DE models, this option is only available at time of order entry and no license for activation is
supported.
To obtain and activate a license for the Universal Temperature Sensor option:
Obtain the device's Serial Number from the local display menu or from the host interface.
Place an order for Universal Temperature Sensor Field Upgrade for SMV 800, part number
#50127216-501 with the Serial Number.
Based on this information the regional distribution center will generate and return a license
key.
The license is activated by entering the License Key parameter value from the local display
menu or host interface.
A restart of the display only will then occur.
License activation can be confirmed by observing that the Universal Temperature Sensor
option is enabled using the local display menu or host interface.

Revision 6.0 SMV800 Series HART/DE Option User’s Manual Page 7
2 Communication Modes
Overview
The SMV800 SmartLine Multivariable Transmitter is available with either Honeywell's Digitally
Enhanced (DE) or HART revision 7 communications protocols. This manual addresses the processes
to configure and calibrate a Transmitter for DE and HART communication.
DE Mode Communication
The SMV800 can transmit its output in either an analog 4 to 20 milliampere format or a Digitally
Enhanced (DE) protocol format for direct digital communications with our TPS/TDC 3000 control
system. In the analog format, only a selected variable is available as an output which can be any one
of the following:
Differential Pressure PV1,
Static Pressure PV2,
Process Temperature PV3, or
Calculated Flow Rate PV4
Note that the secondary variable is only available as a read only parameter through the SCT shown in
Figure 4.
Figure 4 –DE Communication through SCT

Page 8 SMV800 Series HART/DE Option User’s Manual Revision 6.0
In the digital DE protocol format, all four process variables are available for monitoring and control
purposes; and the meter body temperature is also available as a secondary variable for monitoring
purposes only - See
Figure 4
The SMV800 transmitter has no physical adjustments. You need an SCT to make any adjustments in
an SMV800 transmitter. Alternately, certain adjustments can be made through the Universal Station if
the transmitter is digitally integrated with our TPS/TDC 3000 control system.
For more information see section 3.5 SmartLine Configuration Toolkit (SCT 3000)
Digitally Enhanced (DE) Mode Communication
Although it is unnecessary to put a control loop in manual mode before communicating
with a Transmitter operating in DE mode, caution is required if there is potential for error in
identifying the operating mode.
In DE mode, the PV is available for monitoring and control purposes.
Much of the operation in the Digitally Enhanced (DE) mode is similar to that of analog operation.
The essential characteristics of DE transmitter are shown in
Figure 5.
Figure 5 –DE Mode Value Scaling
As indicated at the right of
Figure 5,output values of process variables, as well as communications are transferred to a receiving
device digitally. The digital coding is Honeywell proprietary, which requires the use of DE-capable
Honeywell control equipment.
The use of DE mode offers several advantages:
Process Safety: Unlike analog mode, communications devices do not bump the PV value.
Accuracy: requires less maintenance.
Digital communication: Relatively immune to small variations in circuit resistance or supply
voltage.
Facilitates Maintenance Tasks: Honeywell control systems include operating displays that
enable direct communication with transmitters operating in DE mode.