Honeywell Ademco 5811 User manual

Installation Instructions ADEMCO 5811
One Zone Door/Window Transmitter
The 5811 is a single zone Door/Window Transmitter, compatible with alarm systems that support 5800 series wireless
devices. 5811 has a unique serial number permanently assigned during manufacture, which must be entered into the control
panel upon installation.
NOTES
•Refer to the panel’s installation instructions for programming details.
•During programming of the control unit, 5811 transmitters should be treated as “RF” (i.e. supervised RF) Type.
Mounting
Choose a mounting location for the 5811 where the device is stationary and the magnet is mounted to the moving part of the
door or window. To verify adequate signal strength conduct the Go/No Go test (see control’s instructions) on the 5811 before
mounting permanently.
1. Install the Battery by inserting one edge of the battery under one of the two plastic battery retainer clips, then pressing
down firmly to snap it beneath both clips; see figure 1.
2. Mount the 5811 using double-faced tape (supplied) by affixing it to the back of the unit and mounting the unit in place.
Use screws (optional) if desired; see figure 2. Mount the magnet (supplied) near the alignment marks on the case (see
Diagram).
Replacing an existing unit: The back mounting plate must be replaced when replacing the 5811. Use
standard installation practices when removing the unit to avoid any damage to the mounting surface.
3. Engage the case tabs (see figure 2), then rotate the housing to close. Engage the latch with firm pressure to close and
lock.
Battery Removal
1. Open the housing by inserting a flat blade screwdriver into latch and twisting gently.
2. Remove the old battery cell using a small flat screwdriver into the latch and gently twisting it until the cover becomes
removable (see figure 3).
Figure 1: Battery Installation
Figure 2: Mounting
Figure 3: Battery Removal
Specifications
Dimensions:
2-1/8” (55mm) x 1-3/16" (30mm) x 1/4” (7mm)
Operating Conditions:
23° F (-5° C) to 120° F (50° C)
Relative Humidity 95%, (non-condensing)
Replacement Battery:
Panasonic/Sener CR2032 and Duracell DL2032
1
3
2

NOTE: The FCC ID and IC Certification number is on the back of the plastic case, or see the diagram in the “Figure 3:
Battery Removal” section for the alternate location.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or
User Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment
FCC/IC STATEMENT
This device complies with Part 15 of the FCC Rules,
and RSS-210 of Industry Canada (IC). Operation is
subject to the following two conditions: (1) This device
may not cause harmful interference (2) This device
must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC &
de RSS 210 des
Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas
causer d' interferences nuisibles. (2) Cet appareil doit accepter
toute interference reçue y compris les interferences causant une
reception indésirable.
SUPPORT & WARRANTY
For the latest documentation and online support information, please go to:
www.MyWebTech.Honeywell.com
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
MyWebTech
Warranty
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2013 Honeywell International Inc.
www.honeywell.com/security
Ê800-03928V2oŠ
800-03928V2 4/15 Rev. C