Horizon Fitness IC7.9 User manual

IC7.9 INDOOR CYCLE OWNER’S MANUAL

3
INDOOR CYCLE OPERATION

54
2 ft
60 cm
2 ft
60 cm
2 ft 60 cm
2 ft 60 cm
FRONT
REAR
BIKE
HOW TO MOVE THE INDOOR CYCLE
Due to the weight of the Indoor Cycle, it is recommended
that two persons move it. While one person lifts the back
of the indoor cycle, the second person firmly holds the
handlebar and tips the indoor cycle forward until it rolls on
the wheels. Carefully move the Indoor Cycle to the desired
location and then lower it.
If the Indoor Cycle rocks on the floor after being set
down, turn the leveling feet underneath the front or rear
stabilizer until the rocking motion is eliminated.
Leveling Feet
To reduce the risk of injury, use extreme caution
while moving the indoor cycle. Do not attempt to
move it over uneven surfaces and make sure there’s
a safety space of 20 inch (minimum) to the nearest
equipment is recommended.
WARNING
LOCATION OF THE
INDOOR CYCLE
Place the Indoor Cycle on a
level surface. There should be
2 feet (60 cm) of each side
surround the Indoor Cycle. Do
not place the cycle in any area
that will block any vent or air
openings. The Indoor Cycle
should not be located in a
garage, covered patio, near
water or outdoors.
HOW TO ADJUST THE INDOOR CYCLE
The Indoor Cycle can be adjusted for maximum comfort and exercise effectiveness. The instructions below describe one
approach to adjusting the Indoor Cycle to ensure optimal user comfort and ideal body positioning; you may choose to adjust
the Indoor Cycle differently.
SADDLE ADJUSTMENT
Proper saddle height helps ensure maximum
exercise efficiency and comfort, while
reducing the risk of injury. Adjust the saddle
height to make sure it’s in proper position,
one that keeps a slightly bend in your knee
while your legs are in the extended position.
HANDLEBAR ADJUSTMENT
Proper position for the handlebar is based
primarily on comfort. Typically, the handlebar
should be positioned slightly higher than
the saddle for beginning cyclists. Advanced
cyclists could try different heights to get the
arrangement most suitable for you.
A
B

76
TO ADJUST THE SADDLE HEIGHT:
Rotate the adjustment lever counterclockwise and adjust the saddle to a comfortable pedaling position. Rotate the lever
clockwise to lock saddle position.
TO ADJUST THE SADDLE HORIZONTAL POSITION:
Rotate the adjustment lever counterclockwise to slide the saddle forward or backward as desired. Rotate the lever clockwise
to lock saddle position. Test the saddle slide for proper operation.
Do not adjust the
saddle position
beyond the stop
marks on the
saddle slider
Do not adjust
saddle height
beyond the
stop mark on
the stem
TO ADJUST THE HANDLEBAR HEIGHT:
Rotate the adjustment lever counterclockwise to adjust the handlebar height. Raise or lower the handlebar to the desired
height. Rotate the lever clockwise to lock handlebar position.
TO ADJUST THE PEDAL STRAPS:
Place each foot ankle on the pedal and in the toe clip that the foot ankle is centered over the pedal spindle (center of the
pedal). Rotate one foot to arms reach and pull up on the toe clip strap. Repeat for the other foot. Keep your knees over your
feet as you pedal. To remove your foot from the toe clip, loosen the strap and pull out.
Do not adjust the
handlebar height
beyond the stop
mark on the stem.
The pedal straps should
be adjusted to hold the
foot snugly in the pedal.

98
STOP
TENSION CONTROL AND EMERGENCY BRAKE
The preferred level of difficulty in pedaling (resistance) can be regulated in increments by use of the tension control
lever. To increase the resistance, push the tension control lever downward towards the ground. To decrease the resistance,
pull the handle upwards.
IMPORTANT:
• To stop the flywheel while pedaling, push down hard on the
tension control lever until the brake rubs on the flywheel.
• The flywheel should quickly come to a complete stop.
• Make sure your shoes are fixed into the toe clip.
• Apply full resistance load when the bike is not in use to
prevent injuries due to moving drive gear components.
Tension control lever
Emergency brake
The Indoor Cycle does not have a free moving flywheel; the
pedals will continue to move together with the flywheel
until the flywheel stops. Reducing speed in a controlled
manner is required. To stop the flywheel immediately,
push down hard the tension control lever. Always pedal
in a controlled manner and adjust your desired cadence
according to your own abilities. Push the tension control
lever down = emergency stop.
WARNING
The Indoor Cycle uses a fixed flywheel that builds momentum and will keep the pedals turning even after the user stops pedaling or if
the user’s feet slip off. DO NOT ATTEMPT TO REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT THE MACHINE UNTIL
BOTH THE PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these instructions may lead to loss of
control and the potential for serious injury.
WARNING
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your indoor cycle’s serial number located on
the front stabilizer of the cycle and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: HORIZON INDOOR CYCLE
WARNING
36

1110
MAIN PARTS INCLUDED:
Main Frame
Front Stabilizer
Rear Stabilizer
Handlebar Set
Handlebar Mast Set
Console
Pedal Set
Seat Post Set
PARTS PACKING
INCLUDED:
1 Parts box
1 Owner’s Manual
Saddle
Resistance Control Handle & Emergency Brake
Quick Release
Tablet Holder
Console
Heavy Flywheel
Transportation Wheel
Durable Crank
Seat Post
Seat Slider
MODEL INFORMATION PRE ASSEMBLY
If you have questions or if there
are any missing parts, contact your
local dealer. Contact information
may be located on the back panel
of this manual or on warranty card.
UNPACKING
Due to the weight of the indoor cycle, it is recommended that two persons
perform the assembly. Set the indoor cycle in a cleared area and remove all
packing materials; do not dispose of the packing materials until assembly is
completed.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place
and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
NEED HELP?

1312
IC7.9 ASSEMBLY STEP 1 IC7.9 ASSEMBLY STEP 2
A Attach the FRONT STABILIZER (66) and REAR
STABILIZER (67) to the frame using 4 BOLTS
(69) and 4 WASHERS (72) and 4 NUTS (71), and
secure firmly by WRENCH (78).
HARDWARE FOR STEP 1 : A Thread the LEFT PEDAL (58L) that has “L” on the
spindle to the left side arm of the cycle using the
WRENCH (78). Please note that the “L” pedal
is left-hand threaded which needs to be turned
counter clockwise to tighten.
B Thread the RIGHT PEDAL (58R) that has “R” on
the spindle to the right side arm of the cycle using
the WRENCH (78). Please note that the “R” pedal
is right-hand threaded which needs to be turned
clockwise to tighten.
C Install the HANDLEBAR MAST(36) into the frame
receptor and secure with the quick release.
D Install the SEAT POST(39) into the frame receptor
and secure with the quick release.
NO. DESCRIPTION QTY
69 BOLT 4
71 NUT 4
72 WASHER 4
78 WRENCH 1
71
72
69
78
69
66
71
72
67
71
72
78
36
58R
58L
78
39
HARDWARE FOR STEP 2 :
NO. DESCRIPTION QTY
36 HANDLEBAR MAST 1
39 SEAT POST 1
58L LEFT PEDAL 1
58R RIGHT PEDAL 1
78 WRENCH 1

1514
A Fix CONSOLE (84) with MOUNTING CLAMP (85)
from back.
HARDWARE FOR STEP 4 :
NO. DESCRIPTION QTY
84 CONSOLE 1
85 MOUNTING CLAMP 1
IC7.9 ASSEMBLY STEP 3 IC7.9 ASSEMBLY STEP 4
37
3
38
40
38
39
3
41
HARDWARE FOR STEP 2 :
NO. DESCRIPTION QTY
3QUICK RELEASE 2
37 HANDLEBAR 1
38 WASHERS 4
40 SEAT SLIDER 1
41 SADDLE 1
A Install the HANDLEBAR (37) into the handlebar
mast receptor using 2 WASHERS (38) and secure
with the QUICK RELEASE(3).
B Install the SADDLE (41) into the SEAT SLIDER
(40) receptor and secure with the wrench.
C Attach the SEAT SLIDER (40) to the SEAT POST
(39) using 2 WASHERS (38) and secure with the
QUICK RELEASE(3).
84
85

1716
A Carefully attach the UPPER CONSOLE CABLE
(A) to the LOWER CONSOLE CABLE (B) pre-
assembled to the handlebar.
B Carefully attach the MAST CABLE (C) to the
FRAME CABLE (D) pre-assembled in the frame.
C Adjust console to preferred viewing angle.
NOTE: Check to see there is no loose cable that could
make contact with the flywheel once the cable harness
is assembled. Tuck away any loose cable.
D Congratulations, you have successfully assembled
the Indoor Cycle.
IC7.9 ASSEMBLY STEP 5
A
B
C
D
85
CONSOLE OPERATION

1918
TROUBLESHOOTING
& MAINTENANCE
IC7.9 CONSOLE DISPLAY
MONITOR DISPLAY:
In the exercise mode, the LCD windows will display RPM, KCAL and ODO.
You can press left Key to change the display among TIME/SPEED/CLOCK/DISTANCE
LEFT & RIGHT KEY:
a. Press any key to wake up the console from energy saver mode.
b. During the exercise mode, press left change display among TIME/SPEED/CLOCK/DISTANCE.
IC7.9 CONSOLE OPERATION
CLOCK SETTING
Press the left key until CLOCK is displayed, press the right key for 3 seconds to enter setting mode to adjust clock setting.
Change the value by pressing right key and confirm by pressing left key, the console will automatically save the value given
after 5 seconds.
PERSONAL WORKOUT SETTING
Press the left key until SPEED is displayed, press the right key for 3 seconds to adjust personal data setting. (user weight, gender and
workout time etc.) To change to between standard and metric press the right button when lb or kg is flashing. This will also change
the mile and km setting. Note: when the batteries are replaced the console will default to standard units.
RPM measures the user’s foot RPM, also known as cadence.
Change the value by pressing right key and confirm by pressing left key, the console will automatically save the value given
after 5 seconds.
ENERGY SAVER
To minimize energy consumption, your machine will enter energy saver mode automatically when not in use and could be quickly
woke up with a touch of a button.
KCAL
rpm
40
60
80
100 120 140
160
Am
LEFT KEY RIGHT KEY
MONITOR