Horizon Fitness GR3 User manual

GR3 GR5 GR6
OWNER’S MANUAL
BEDIENUNGSANLEITUNG
GEBRUIKERSHANDLEIDING
MANUEL D‘UTILISATION
HZ18_GR3-5-6 OM r1_4_A.indd 1 4/26/18 9:13 AM

3
INDOOR CYCLE OPERATION
ENGLISH
3ENGLISH
35 DEUTSCH
67 NEDERLANDS
99 FRANÇAIS
HZ18_GR3-5-6 OM r1_4_A.indd 2-3 4/26/18 9:13 AM

54
GR3
GR5
GR6
GR3
GR5
GR6
2 ft
60 cm
2 ft
60 cm
2 ft 60 cm
2 ft 60 cm
FRONT
REAR
BIKE
HOW TO MOVE THE INDOOR CYCLE
Due to the weight of the Indoor Cycle, it is recommended
that two persons move it. While one person lifts the back
of the indoor cycle, the second person firmly holds the
handlebar and tips the indoor cycle forward until it rolls
on the wheels. Carefully move the Indoor Cycle to the
desired location and then lower it.
If the Indoor Cycle rocks on the floor after being set
down, turn the leveling feet underneath the front or rear
stabilizer until the rocking motion is eliminated.
Leveling Feet
To reduce the risk of injury, use extreme caution
while moving the indoor cycle. Do not attempt to
move it over uneven surfaces and make sure there’s
a safety space of 20 inch (minimum) to the nearest
equipment is recommended.
WARNING
LOCATION OF THE
INDOOR CYCLE
Place the Indoor Cycle on a level
surface. There should be 2 feet
(60 cm) of each side surround
the Indoor Cycle. Do not place
the cycle in any area that will
block any vent or air openings.
The Indoor Cycle should not be
located in a garage, covered
patio, near water or outdoors.
( GR6 SHOWN )
( GR6 SHOWN )
HOW TO ADJUST THE INDOOR CYCLE
The Indoor Cycle can be adjusted for maximum comfort and exercise effectiveness. The instructions below describe one
approach to adjusting the Indoor Cycle to ensure optimal user comfort and ideal body positioning; you may choose to adjust the
Indoor Cycle differently.
SADDLE ADJUSTMENT
Proper saddle height helps ensure maximum
exercise efficiency and comfort, while
reducing the risk of injury. Adjust the saddle
height to make sure it’s in proper position, one
that keeps a slightly bend in your knee while
your legs are in the extended position.
HANDLEBAR ADJUSTMENT
Proper position for the handlebar is based
primarily on comfort. Typically, the handlebar
should be positioned slightly higher than
the saddle for beginning cyclists. Advanced
cyclists could try different heights to get the
arrangement most suitable for you.
B
A
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 4-5 4/26/18 9:13 AM

76
GR3
GR5
GR6
GR3
GR5
GR6
TO ADJUST THE SADDLE HEIGHT:
Rotate the adjustment lever counterclockwise and adjust the saddle to a comfortable pedaling position. Rotate the lever
clockwise to lock saddle position.
TO ADJUST THE SADDLE HORIZONTAL POSITION:
Rotate the adjustment lever counterclockwise to slide the saddle forward or backward as desired. Rotate the lever clockwise to
lock saddle position. Test the saddle slide for proper operation.
Do not adjust the
saddle position
beyond the stop
marks on the
saddle slider
Do not adjust
saddle height
beyond the
stop mark on
the stem
TO ADJUST THE HANDLEBAR HEIGHT:
Rotate the adjustment lever counterclockwise to adjust the handlebar height. Raise or lower the handlebar to the desired
height. Rotate the lever clockwise to lock handlebar position.
TO ADJUST THE PEDAL STRAPS:
Place each foot ankle on the pedal and in the toe clip that the foot ankle is centered over the pedal spindle (center of the
pedal). Rotate one foot to arms reach and pull up on the toe clip strap. Repeat for the other foot. Keep your knees over your
feet as you pedal. To remove your foot from the toe clip, loosen the strap and pull out.
Do not adjust the
handlebar height
beyond the stop
mark on the stem
The pedal straps should
be adjusted to hold the
foot snugly in the pedal .
( GR6 SHOWN )( GR6 SHOWN )
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 6-7 4/26/18 9:13 AM

98
GR3
GR5
GR6
TENSION CONTROL AND EMERGENCY BRAKE
The preferred level of difficulty in pedaling (resistance) can be regulated in fine increments by use of the tension control
knob. To increase the resistance, turn the tension control knob clockwise. To decrease the resistance, turn the knob counter
clockwise.
IMPORTANT:
• To stop the flywheel while pedaling, push down on the red
emergency brake lever.
• The flywheel should quickly come to a complete stop.
• Make sure your shoes are fixed into the toe clip.
• Apply full resistance load when the bike is not in use to
prevent injuries due to moving drive gear components.
The Indoor Cycle does not have a free moving flywheel; the
pedals will continue to move together with the flywheel until
the flywheel stops. Reducing speed in a controlled manner
is required. To stop the flywheel immediately, push down
the red emergency brake lever. Always pedal in a controlled
manner and adjust your desired cadence according to your
own abilities. Push the red lever down = emergency stop.
WARNING
The Indoor Cycle uses a fixed flywheel that builds momentum and will keep the pedals turning even after the user stops pedaling or if the
user’s feet slip off. DO NOT ATTEMPT TO REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT THE MACHINE UNTIL BOTH
THE PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these instructions may lead to loss of control and
the potential for serious injury.
WARNING
Tension control knob
Emergency brake
( GR6 SHOWN )
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your indoor cycle’s serial number located on the front
stabilizer of the cycle and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: HORIZON INDOOR CYCLE
WARNING
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 8-9 4/26/18 9:13 AM

1110
Saddle
Tension Control Knob & Emergency Brake
Adjustment Knob
Heavy Flywheel
Transportation Wheel
Durable Crank
( GR6 SHOWN )
Seat Post
Seat Slider
MODEL INFORMATION
GR6
SHOWN
GR3
GR5
GR6
PRE ASSEMBLY
MAIN PARTS INCLUDED:
1 Main Frame
Front & rear stabilizer
Handlebar Set
Handlebar Mast Set (Only GR6)
Seat Post Set
Pedal Set
PARTS PACKING
INCLUDED:
1 Parts box
1 Owner’s Manual
If you have questions or if there
are any missing parts, contact your
local dealer. Contact information
may be located on the back panel
of this manual or on warranty card.
UNPACKING
Due to the weight of the indoor cycle, it is recommended that two persons
perform the assembly. Set the indoor cycle in a cleared area and remove all
packing materials; do not dispose of the packing materials until assembly is
completed.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
NEED HELP?
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 10-11 4/26/18 9:13 AM

1312
GR3
GR3 ASSEMBLY STEP 1
A Install the HANDLEBAR (1) into the frame receptor
and secure with the knob.
B Install the SEAT POST (2) into the frame receptor
and secure with the knob.
C Thread the LEFT PEDAL (3) that has “L” on the
spindle to the left side arm of the cycle using the
COMBINATION WRENCH (5). Please note that
the L pedal is left-hand threaded which needs to be
turned counter clockwise to tighten.
D Thread the RIGHT PEDAL (4) that has “R” on the
spindle to the right side arm of the cycle using the
COMBINATION WRENCH (5). Please note that the
R pedal is right-hand threaded which needs to be
turned clockwise to tighten.
GR3
1
2
45
3
HARDWARE FOR STEP 1 :
GR3 ASSEMBLY STEP 2
A Attach the FRONT STABILIZER (9) to the frame
using 2 ALLEN BOLTS (7) and 2 WASHERS (8),
and secure firmly by ALLEN WRENCH (6).
B Attach the REAR STABILIZER (10) to the frame
using 2 ALLEN BOLTS (7) and 2 WASHERS (8),
and secure firmly by ALLEN WRENCH (6).
6
8
7
9
10
8
7
6
NO. DESCRIPTION QTY
1HANDLEBAR 1
2SEAT POST 1
3LEFT PEDAL 1
4RIGHT PEDAL 1
5COMBINATION WRENCH 1
HARDWARE FOR STEP 2 :
NO. DESCRIPTION QTY
6ALLEN WRENCH 1
7ALLEN BOLTS (M8 X 16L) 8
8WASHERS 8
9FRONT STABILIZER 1
10 REAR STABILIZER 1
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 12-13 4/26/18 9:13 AM

1514
GR5GR5
GR5 ASSEMBLY STEP 1
A Attach the REAR STABILIZER (1) to the frame
using 2 NUTS (3), 2 WASHERS (4) and 2 BOLTS
(2), and secure firmly using the adjustable
WRENCH (5).
B Attach the FRONT STABILIZER (6) to the
frame using 2 NUTS (3), 2 WASHERS (4) and 2
BOLTS (2), and secure firmly using the adjustable
WRENCH (5).
4
1
2
3
5
2
6
4
3
GR5 ASSEMBLY STEP 2
A Thread the LEFT PEDAL (8) that has “L” on the
spindle to the left side arm of the cycle using the
adjustable WRENCH (5). Please note that the
L pedal is left-hand threaded which needs to be
turned counter clockwise to tighten.
B Thread the RIGHT PEDAL (7) that has “R” on the
spindle to the right side arm of the cycle using the
adjustable WRENCH (5). Please note that the R
pedal is right-hand threaded which needs to be
turned clockwise to tighten.
C Install the HANDLEBAR (9) into the frame receptor
and secure with the quick release.
8
7
9
5
HARDWARE FOR STEP 1 :
NO. DESCRIPTION QTY
1REAR STABILIZER 1
2BOLTS 4
3NUTS 4
4WASHERS 4
5WRENCH 1
6FRONT STABILIZER 1
HARDWARE FOR STEP 2 :
NO. DESCRIPTION QTY
5WRENCH 1
7RIGHT PEDAL 1
8LEFT PEDAL 1
9HANDLEBAR 1
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 14-15 4/26/18 9:13 AM

1716
GR6 ASSEMBLY STEP 1
A Attach the FRONT STABILIZER (4) and REAR
STABILIZER (5) to the frame using 4 BOLTS (1)
and 4 WASHERS (3) and 4 NUTS (2), and secure
firmly by WRENCH (6).GR6
1
2
3
4
5
2
3
6
2
3
1
6
GR6
GR6 ASSEMBLY STEP 2
A Thread the LEFT PEDAL (10) that has “L” on the
spindle to the left side arm of the cycle using the
WRENCH (6). Please note that the L pedal is left-
hand threaded which needs to be turned counter
clockwise to tighten.
B Thread the RIGHT PEDAL (9) that has “R” on the
spindle to the right side arm of the cycle using the
WRENCH (6). Please note that the R pedal is right
hand threaded which needs to be turned clockwise
to tighten.
C Install the HANDLEBAR MAST(7) into the frame
receptor and secure with the quick release.
D Install the SEAT POST(8) into the frame receptor
and secure with the quick release.
9
10
6
7
8
HARDWARE FOR STEP 1 :
NO. DESCRIPTION QTY
1BOLTS 4
2NUTS 4
3WASHERS (M8) 4
4FRONT STABILIZER 1
5REAR STABILIZER 1
6WRENCH 1
HARDWARE FOR STEP 2 :
NO. DESCRIPTION QTY
6WRENCH 1
7HANDLEBAR MAST 1
8SEAT POST 1
9RIGHT PEDAL 1
10 LEFT PEDAL 1
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 16-17 4/26/18 9:13 AM

1918
GR6
GR6 ASSEMBLY STEP 3
A Install the HANDLEBAR (12) into the handlebar
mast receptor using 2 WASHERS (13) and secure
with the QUICK RELEASE(11).
B Install the SADDLE (14) into the SEAT SLIDER
(15) receptor and secure with the wrench.
C Attach the SEAT SLIDER (15) to the SEAT POST
(8) using 2 WASHERS (13) and secure with the
QUICK RELEASE(11).
12
13
11
15
13
11
14
TROUBLESHOOTING
& MAINTENANCE
HARDWARE FOR STEP 3 :
NO. DESCRIPTION QTY
11 QUICK RELEASE 2
12 HANDLEBAR 1
13 WASHERS (M10) 4
14 SADDLE 1
15 SEAT SLIDER 1
ENGLISH
ENGLISH
HZ18_GR3-5-6 OM r1_4_A.indd 18-19 4/26/18 9:13 AM