Howard Miller HEKMAN 79167P User manual

A HOWARD MILLER COMPANY
79167P PEDESTALS & MODESTY PANELS
79167T TOP PANEL
Assembly Instruction
Page 1 of 3
PART INSIDE
1 2 3
TOP ASSEMBLIES (2 Pcs) PEDESTALS (2 Pcs) MODESTY PANEL (2 Pcs)
A C D
ALLEN BOLT
5
16" X 2" (4 PCS.)
HARDWARE LIST
ALLEN BOLT
5
16" X 6" (2 PCS.)
FLAT WASHER M8
(9 PCS.) SPRING W. M8
(9 PCS.)
E
J
THE DESK CANNOT BE MOVED AFTER IT IS ASSEMBLED SO IT MUST BE ASSEMBLED IN THE AREA
IT WLL BE USED.
THE PEDESTAL WITH THE DOOR IS ON THE LEFT AS YOU ARE SITTING AT THE DESK
THE PEDESTAL WITH THE DRAWER IS ON THE RIGHT AS YOU ARE SITTING AT THE DESK.
STEP 1.
ASSEMBLE THE LEFT PEDESTAL (2) AND THE LEFT
MODESTY PANEL (3) WITH ALLEN BOLTS (A),
SPRING WASHER (D), FLAT WASHER (C) USE
ALLEN KEY (J) BUT DO NOT TIGHTEN THE BOLTS
COMPLETELY AT THIS TIME.
STEP 2.
ASSEMBLE THE RIGHT PEDESTAL (2)
AND THE RIGHT MODESTY PANEL (3)
SAME AS STEP 1.
C
D
A
J
L
F
G
ALLEN BOLT
M6 X 35 (1 PC.)
ALLEN KEY L4 (For M6)
(1 PC.)
H
ALLEN BOLT
5
16" X 1 1 2"(3 PCS.)
B
FLAT WASHER M6
(1 PC.) SPRING W. M6 (1 PC.) ALLEN KEY L5 (For 5
16")
(1 PC.)
I
SCREW Ø6 x 5
8"
(8 PCS.)
K
"L" BRACKET
(4 PCS.)

Page 2 of 3
STEP 3.
PLACE THE LEFT TOP ASSEMBLY ON THE LEFT
PEDESTAL AND LEFT MODESTY PANEL. THE TOP
ASSEMBLY IS SET FORWARD ON THE PEDESTAL
THEN SLID BACK TO LOCK THE FRENCH CLEATS
THAT ARE ON THE BOTTOM OF THE TOP
ASSEMBLY WITH THE MATCHING SET ON THE
TOP OF THE PEDESTAL.
OPEN THE DOOR ON THE LEFT PEDESTAL TO
SECURE THE LEFT TOP ASSEMBLY TO THE LEFT
PEDESTAL WITH ALLEN BOLT (E), SPRING
WASHER (D), FLAT WASHER (C) BY USING ALLEN
KEY (J).
STEP 4.
PLACE THE RIGHT TOP ASSEMBLY ON THE RIGHT
PEDESTAL AND RIGHT MODESTY PANEL.
THE TOP ASSEMBLY IS SET FORWARD ON THE
PEDESTAL THEN SLID BACK TO LOCK THE
FRENCH CLEATS THAT ARE ON THE BOTTOM OF
THE TOP ASSEMBLY WITH THE MATCHING SET
ON THE TOP OF THE PEDESTAL.
E
D
C
J
OPEN THE TOP DRAWER IN THE PEDESTAL TO SECURE
THE RIGHT TOP ASSEMBLY TO THE RIGHT PEDESTAL
WITH ALLEN BOLT (E), SPRING WASHER (D), FLAT
WASHER (C) BY USING ALLEN KEY (I).
"E" TYPE
"E" TYPE
C
D
E
J

Page 3 of 3
STEP 5.
IN THE AREA THE DESK WILL BE USED.
SLIDE THE TWO HALF-DESK ASSEMBLIES TOGETHER BY
LINING UP THE PINS. THEN LOCK THE TWO TOPS WITH THE
TABLE LOCK HARDWARE.
CONNECT THE MODESTY PANEL WITH ALLEN BOLT (B) ,
SPRING WASHER (D), FLAT WASHER (C) USE ALLEN KEY (J)
BUT DO NOT TIGHTEN THE BOLTS COMPLETELY AT THIS
TIME.
STEP 6.
ATTACH THE CORNER BLOCK BETWEEN
THE TWO DROP FRONT DRAWER WITH
ALLEN BOLT (F) , SPRING WASHER (H),
FLAT WASHER (G) USE ALLEN KEY (I) BUT
DO NOT TIGHTEN THE BOLTS
COMPLETELY AT THIS TIME.
STEP 7.
WITH ALL THE ALLEN BOLTS STARTED
YOU CAN TIGHTEN ALL THE ALLEN
BOLTS PULLING THE ASSEMBLIES TIGHT
AND INTO THE CORRECT FIT.
C
D
B
J
F
H
G
I
"B" TYPE
"F" TYPE
STEP 8.
INSTALL THE "L" BRACKET (K) ONTO THE
MODESTY PANELS AND TOP PANELS USING
SCREW (L) TIGHTEN WITH SCREW DRIVER
(NOT INCLUDED)
K
L