Howard Miller HEKMAN 79187P User manual

A HOWARD MILLER COMPANY
79187P PEDESTALS & MODESTY PANELS
79187T TOP PANELS
Assembly Instruction
PART INSIDE
1 2 3
TOP ASSEMBLIES (2 Pcs) PEDESTALS (2 Pcs) MODESTY PANELS (2 Pcs)
A
ALLEN BOLT
5
16" X 2" (13 PCS.)
HARDWARE LIST
G
THE DESK CANNOT BE MOVED AFTER IT IS ASSEMBLED SO IT MUST BE ASSEMBLED IN THE AREA
IT WLL BE USED.
THE PEDESTAL WITH THE DOOR IS ON THE LEFT AS YOU ARE SITTING AT THE DESK
THE PEDESTAL WITH THE DRAWER IS ON THE RIGHT AS YOU ARE SITTING AT THE DESK.
STEP 1.
ASSEMBLE THE LEFT PEDESTAL (2) AND THE LEFT
MODESTY PANEL (3) WITH ALLEN BOLTS (A),
SPRING WASHER (E), FLAT WASHER (D) USE
ALLEN KEY (F) BUT DO NOT TIGHTEN THE BOLTS
COMPLETELY AT THIS TIME.
STEP 2.
ASSEMBLE THE RIGHT PEDESTAL (2)
AND THE RIGHT MODESTY PANEL (3)
SAME AS STEP 1.
E
ALLEN KEY L5
For 5
16" & M8 (1 PC.)
F
Page 1 of 3
C
ALLEN BOLT
5
16" X 6" (2 PCS.)
SPRING WASHER M8
(17 PCS.)
B
ALLEN BOLT
M8 X 40 (2 PCS.)
COVERCAPS
(6 PCS.)
D
D
E
A
F
"A" TYPE
G
FLAT WASHER M8
(17 PCS.)

Page 2 of 3
STEP 3.
PLACE THE LEFT TOP ASSEMBLY ON THE LEFT
PEDESTAL AND LEFT MODESTY PANEL. THE TOP
ASSEMBLY IS SET FORWARD ON THE PEDESTAL THEN
SLID BACK TO LOCK THE FRENCH CLEATS THAT ARE
ON THE BOTTOM OF THE TOP ASSEMBLY WITH THE
MATCHING SET ON THE TOP OF THE PEDESTAL.
STEP 4.
PLACE THE RIGHT TOP ASSEMBLY ON THE RIGHT
PEDESTAL AND RIGHT MODESTY PANEL.
THE TOP ASSEMBLY IS SET FORWARD ON THE PEDESTAL
THEN SLID BACK TO LOCK THE FRENCH CLEATS THAT
ARE ON THE BOTTOM OF THE TOP ASSEMBLY WITH THE
MATCHING SET ON THE TOP OF THE PEDESTAL.
OPEN THE TOP DRAWER IN
THE PEDESTAL TO SECURE
THE RIGHT TOP ASSEMBLY
TO THE RIGHT PEDESTAL
WITH ALLEN BOLT (B),
SPRING WASHER (E), FLAT
WASHER (D) AND ALLEN
BOLT (A), SPRING WASHER
(E), FLAT WASHER (D)BY
USING ALLEN KEY (F).
OPEN THE DOOR ON THE LEFT PEDESTAL
TO SECURE THE LEFT TOP ASSEMBLY TO
THE LEFT PEDESTAL WITH ALLEN BOLT
(B), SPRING WASHER (E), FLAT WASHER
(D) AND ALLEN BOLT (A), SPRING
WASHER (E), FLAT WASHER (D) BY USING
ALLEN KEY (F).
"B" TYPE
"B" TYPE
"A" TYPE
B
E
D
F
D
E
A
I
"A" TYPE
B
E
D
F
D
E
A
F
ATTACH MODESTY PANEL TO TOP
ASSEMBLY WITH ALLEN BOLT (A)
SPRING WASHER (E) AND FLAT
WASHER (D). DO NOT FULLY
TIGHTEN THE BOLTS IN STEP 3 OR 4
UNTIL STEP 7.
ATTACH MODESTY PANEL TO
TOP ASSEMBLY WITH ALLEN
BOLT (A) SPRING WASHER (E)
AND FLAT WASHER (D). DO
NOT FULLY TIGHTEN THE
BOLTS IN STEP 3 OR 4 UNTIL
STEP 7.

Page 3 of 3
STEP 5.
IN THE AREA THE DESK WILL BE USED.
SLIDE THE TWO HALF-DESK ASSEMBLIES
TOGETHER BY LINING UP THE PINS. THEN LOCK
THE TWO TOPS WITH THE TABLE LOCK
HARDWARE.
CONNECT THE MODESTY PANEL WITH ALLEN
BOLT (A) , SPRING WASHER (E), FLAT WASHER
(D) USE ALLEN KEY (F) TIGHTEN ALL THE
BOLTS COMPLETELY AT THIS TIME.
STEP 6.
ATTACH THE CORNER BLOCK BETWEEN THE TWO DROP
FRONT DRAWER WITH ALLEN BOLT (C) , SPRING WASHER
(E), FLAT WASHER (D) USE ALLEN KEY (F) BUT DO NOT
TIGHTEN THE BOLTS COMPLETELY AT THIS TIME.
C
E
D
F
"C" TYPE
"A" TYPE
A
E
D
F
G
STEP 7.
WITH ALL THE ALLEN BOLTS STARTED YOU CAN TIGHTEN ALL THE ALLEN BOLTS PULLING THE
ASSEMBLIES TIGHT AND INTO THE CORRECT FIT.
COVER THE BOLTS WITH COVER CAPS (G).