HUANUO HNHM4 User manual

Thank you for choosing this Huanuo product! At Huanuo we
strive to provide you with the best quality products and
services in the industry. Please share your experience ofour
productwith others on www.huanuoav.com/reviews if you are
satisfied. Should you have any issues, please don't hesitate to
contactus.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
OtherInfo:
[e-mail] (US/CA/DE/UK/FR/IT/ES/AU)
1
Model:HNHM4
Monitor Table
Instruction Manual

X1
01 04
X1
05 X2 06 X2 07 X4 08 X1 X1 09 10
X1
02 X1 X1 03
M3x8mm
D x2
1/8 in.(3mm)
E x1
15/64 in.(6mm)
F x1
M8x10mm
A x2
M5x16mm
B x3 C x2
•Carefully open the carton, remove contents and lay out on cardboard or other
protective surface to avoid damage.
•Check package contents against the Supplied Parts and Hardware to assure that all
components were received undamaged. Do not use damaged or defective parts.
•Not all parts and hardware included will be used. lf you require replacement parts,
contact customer service at [email protected]
•Carefully read all instructions before attempting installation.
•If you do not understand the instructions or have any concerns or questions, please
contact customer service at [email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaim any liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
UNPACKING INSTRUCTIONS AND IMPORTANT SAFETY INFORMATION
Supplied Parts and Hardware
UNPACKING INSTRUCTIONS AND IMPORTANT SAFETY INFORMATION
M4x12mm
M-A X8
M4x16mm
M-B X8
M5x12mm
M-C X8
M5x16mm
M-D X8
D5
M-E X8 M-F X8
1

Step 2A-1
2
STEP 2A
01
02
B
E
E
03
For C Clamp Mounting
01
STEP 1 Connect Upper Pole to Lower Pole
S
S
02
02
02
Install part [03] to pole [02]
Step 1-1 Loosen the screw [S] on pole [02] using Allen key [E]
Step 1-2 Connect pole [01] to pole [02]
Step 1-2 Tighten the screw [S] using Allen key [E] to fix the two poles
1/8 in.(3mm)
1/8 in.(3mm)

Adjust the mount
according to the thickness of desktop
Step 1A-2
Step 2B-1 Install part [09] to pole [02]
Step 2B-2 Remove part [a] from part [04]
Install part
[04] to part [03]
Secure the
mount to the desktop
3
STEP 2B
A
B
E
F
04
02
03
04
09
10 a
For Grommet Mounting
a
Step 1A-3 Step 1A-4
Secure the mount to the
desktop
Step 2B-3
1/8 in.(3mm)
F15/64 in.(6mm)
15/64 in.(6mm)
45mm(1 in.)
-
80mm(3 in.)
＜ 45mm
(1 in.)

Step 3-1
4
05
07
Check Monitor Hole Pattern and Select Monitor Bolts
Step 4
MAX:100 mm
MAX:100
mm
M5M4
Only one bolt size fits your TV.
100 mm ≈ 7 7/8 in.
75 mm ≈ 4 in.
Step 3 Install Cable Clips & MonitorConnectorto the Pole Assembly
F
Slide the two cable clips [07]
and the monitor connector
[05] to the pole assembly
Step 3-1 Step 3-2
Secure the monitor connector [05]
to the pole assembly,then attach the
cable clips [08] to the monitor
connector [05]
Step 3-2
08
15/64 in.(6mm)

M-A/M-C
M-E
06
M-B/M-D
M-E
M-F
FLAT BACK MONITOR
(UNIVERSAL MONITOR PLATE)
ROUND BACK MONITOR
(UNIVERSAL MONITOR PLATE)
5
Hang Monitors to the Stand and Secure with Knobs [C]and Bolts [D]
Step 6
Attach the Monitor Plates to the Monitors
Step 5
Bolt length:Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the monitor.
-Too long will damage the monitor.
D
C

6
Fix Tilt Angle of thr Monitors
Step 7
Manage CablesStep 8
F15/64 in.(6mm)

7
Features
Store Allen Keys into the Cable Clip
Step 9
F 15/64 in.(6mm)
E 1/8 in.(3mm)
180°
360°
360°
Tilt Tilt
Individual VESA plate
height adjustment helps
monitors to be perfectly
aligned.