Huawei BTS3900A Original operating instructions

BTS3900A (Ver.C)
Quick Installation
Issue: 01
Date: 2011-04-30
HUAWEI TECHNOLOGIES CO., LTD.
Guide

zThis document is applicable to GSM V100 or V300, SRAN V1
zIn this document, the equipment appearance is for reference
o
the figures.
Appearance of the Cabinets
APM30H TMC11H RF
C
The main components of the BTS3900A are t
h
IBBS200D, IBBS200T, and TMC11H.
Cabinet Dimensions and Clearance R
e
zThe dimensions (W x H x D) of the APM30H, RFC, TM
C
IBBS200T (excluding the protecting hood for the TEC co
o
mm x 480 mm.
zThe recommended distance between the cabinets is 4
0
distance between the cabinets is 150 mm
distance
between
the
cabinets
is
150
mm
.
zIf the Noise Reduction Module (NRM) is installed, the d
cabinets is 150 mm.
480
m
>300mm
40mm
Cabinet
600mm 40m
m
600mm
Cabinet
Overview of the Cabinets
>800mm
Maximum
120°
APM30H
BBU
R
RFC
RRRRR
EPU
Overview
of
the
Cabinets
Fan box
Junction
box
PMU
SLPU
Ground-
in
g
bar
DCDU-11A
1
BBU
F
U
F
U
F
U
F
U
F
U
F
U
Ground-
ing bar
gba
00, and WCDMA V200.
o
nly. The actual equipment may differ from what is shown in
C
IBBS200D IBBS200T
h
e APM30H and the RFC. Optional components are the
TEC l h d (D h 206 )
e
quirements
TEC
coo
l
er
h
oo
d
(D
ept
h
:
206
mm
)
C
11H, IBBS200D, or
o
ler) are 600 mm x 700
0
mm, and the maximum
600mm
480mm
istance between the
700mm
700mm
m
m>300mm
>60mm
600mm
m
Cabinet
700mm
200mm
TMC11H (-48 V DC power supply)
TMC11H
Junction box
DCDU-11C BBU
SLPU
Junction
box
DCDU-11C
1
Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved.
Grounding bar Ground-
ing bar

IBBS200D
Power
Overview of the Cabinets
CMUE
Power
distribution box
Power box of the
heating film
Grounding bar
Installing the Base
The installation blocks are placed in the auxiliar
y
material package of the RFC.
Φ16
52-60 mm
90°
Φ16
Base
Expansion
Flat was
h
Spring w
a
M12x60
B
Concrete
plinth
Installing the Cabinets
Concrete
plinth
Expansion
tube
Re
m
pla
t
1 Attaching the Cabinet to the Base
Installing
the
Cabinets
2. TM
C
1. RFC
M12x30 Bolt
(×2)
Gaske
t
an obl
o
hole
2
IBBS200T
Power
CMUE
Power
distribution box
Grounding bar
Level
bar
y
M12x40
Install two installation
blocks on the base
before installing only
the RFC.
Remove the
baffle plates
from the both
sides and the
rear of the
base.
Bolt (×2)
Expansion bolt (x4)
n
h
er
a
sher
B
olt
Adjusting pad
n
m
ove the front cover
t
e from the base.
C
11H/IBBS200T/IBBS200D
By attaching the IBBS200D as an example, attaching
the TMC11H or the IBBS200T to the base is the same.
M12×30
Bolt（×4）
t
with
o
ng
Gasket with an
oblong hole
2

2 Stacking the Cabinets
Remove the
(x4) from th
e
cabinet.
Remove the cover plates (×2) from
the top of the lower cabinet.
To ensure the waterp
r
of the cabinet, keep
w
plates for the round h
o
Earth Grounding the Cabin
e
Principles for grounding
the BTS3900A:
Cover plate
zThe upper cabinets are connected to the lower
cabinets with equipotential cables.
zThe lower cabinets are connected to the RFCs.
zThe RFCs are connected to the grounding
busbar with PGND cables.
the
BTS3900A:
A
P
M
R
3
PGND cable (25 mm2)Equipotential cable (25 mm2)
plastic screws
e
top of the lower
Stack the cabinets, and attach
the cabinets with the bolts(×4).
Gktith
G
as
k
e
t
w
ith
an
oblong hole
M12x30
r
oof performance
w
ell the cover
o
le of the cabinet.
Gasket with
an oblong
e
ts The PGND cable and signal cable cannot
be bound or entangled. A certain distance
must be reserved between them to prevent
interference from each other
M12x30
Blot (x4)
an
oblong
hole
interference
from
each
other
.
Grounding bar
APM30H
M
30H
RFC
R
FC
3
Grounding busbar

Installing the Cables
zIn this section, the color of the cables and the equipment app
e
z
If the signal cable between the cabinets is redundant coil and
1 Connecting the Power Cables
a
Principles for routing the power cables
1 The -48 V power cable and PGND cable must be
b
2 The
p
ower cable must be se
p
aratel
y
bundled and
z
If
the
signal
cable
between
the
cabinets
is
redundant
,
coil
and
-48 V DC Power Supply Scenario
a
ppy
Multiple power cables must be bundled when rout
e
3 If the length of the power cable is insufficient, repl
a
joints to lengthen the cable.
If the TMC11H (-48 V DC power supply) is required, then it is th
e
the next.
Connect the input power cable for the RFC.
4
e
arance are for reference only.
d tie the extra length of the cable in the base
b
undled together.
cannot be bundled to
g
ether with other cables an
y
where.
d
tie
the
extra
length
of
the
cable
in
the
base
.
gy
e
d.
a
ce the cable rather than adding connectors or soldering
e
-48 V DC power supply scenario. if not, skip this section to
4

1 Connecting the Power Cables
AC Power Supply Scenario
b
1. Connect the input power cable for the AP
M
Remove the AC protecting cap, open the AC input po
w
Recover the AC protecting cap, close the AC input po
w
220 V three-phase AC mode 220 V single-pha
s
L1 wire
Remove
L2 wire
L3 wire
N wire
2. Connect the power cables between the AP
2.
Connect
the
power
cables
between
the
AP
Input power cable for the TMC11H
5
M
30H
Connect the APM30H AC input power cable.
w
er box.
110 V AC mode
w
er box.
s
e AC mode
L wire PE wire
N wire
L2 wire
L1 wire
N wire
PE wire
M30H and the TMC11H
M30H
and
the
TMC11H
Power cable for the junction box in the TMC11H
5

1 Connecting the Power Cables
AC Power Supply Scenario
3. Connect the power cable between the AP
M
(APM:IBBS=1:2
）
b
(APM:IBBS=1:2
）
zThis chapter is applicable
to the scenario where the
number of configured
APM30Hs is half that of
configured IBBS200Ds or
IBBS200Ts.
Power cables for the
IBBS200Ds or IBBS200Ts
IBBS200Ts.
zEither the IBBS200D or
the IBBS200T is installed.
Power cables for the fans in
the IBBS200Ds
6
M
30H and IBBS200D or IBBS200T
6

1 Connecting the Power Cables
AC Power Supply Scenario
3. Connect the power cable between the AP
M
(APM:IBBS=1:2
）
b
Power cables for the heating films
in the IBBS200Ds
zPrevent the wires from
exposing out of the power box
of the heating film
(APM:IBBS=1:2
）
From L2/N2
The power
box of the
heating film
of
the
heating
film
.
zMust route the
p
ower cables
From L1/N1
p
for the heating films in the
IBBS200Ds into the power box
of the heating film from the top
down.
The
p
ower
F
r
L
O
Power cables for the TECs in
the IBBS200Ts
p
box of the
heating film
F
r
L
O
7
M
30H and IBBS200D or IBBS200T
r
om
O
AD3
r
om
O
AD2
7

1 Connecting the Power Cables
AC Power Supply Scenario
4. Connect the power cable between the AP
M
(APM:IBBS=1:1
）
b
This chapter is applicable
to the scenario where the
number of configured
APM30Hs equals that of
configured IBBS200Ds or
IBBS200Ts
(APM:IBBS=1:1
）
Power cables for the
IBBS200Ds or IBBS200Ts
IBBS200Ts
.
Either the IBBS200D or
the IBBS200T is installed.
Power cables for the fans
in the IBBS200Ds
8
M
30H and IBBS200D or IBBS200T
8

1 Connecting the Power Cables
AC Power Supply Scenario
4. Connect the power cable between the AP
M
(APM:IBBS=1:1
）
b
Power cables for the
heating films in the IBBS200Ds
zPrevent the wires from
exposing out of the power box
of the heatin
g
film.
(APM:IBBS=1:1
）
The power
box of the
heating film
g
zMust route the power cables
for the heating films in the
IBBS200Ds into the power box
of the heating film from the top
down.
The power
box of the
heating film
Power cables for the
TECs in the IBBS200Ts
9
M
30H and IBBS200D or IBBS200T
9