Huawei PowerCube 500 User manual

1
Issue: 01
Date: 2018-05-20
PowerCube 500 Quick Guide (Kenya Safe City, PC500-300G1)
Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.
1 Overview
Function module: PC500-300G1
Lithium battery: CBM20E-N14A1
Appearance Grid Hybrid Scenario
Lithium
Battery
Indicator
Color
Status
Meaning
Run
indicator
(RUN)
Green
Off
The lithium battery has no power input
or is faulty.
Steady on
The lithium battery is powered on.
Blinking
slowly
(0.5 Hz)
The lithium battery is communicating
properly with upstream monitoring
equipment.
Blinking
fast (4 Hz)
The lithium battery fails to
communicate with upstream
monitoring equipment.
Alarm
indicator
(ALM)
Red
Off
There is no alarm.
Steady on
The lithium battery has generated a
fault alarm and needs to be replaced.
Blinking
slowly
(0.5 Hz)
The lithium battery has generated a
protection alarm, which can be cleared.
Function
Module
Indicator
Color
Status
Meaning
Run
indicator
Green
Off
The function module has no power input
or is faulty.
Blinking
slowly
(0.5 Hz)
The function module is communicating
properly with upstream monitoring
equipment.
Blinking
fast (4
Hz)
The function module fails to
communicate with upstream monitoring
equipment.
Alarm
indicator
Yellow
Off
There is no alarm.
Blinking
slowly
The function module has generated an
alarm, which can be cleared.
Steady
on
The function module has generated an
AC power failure or PV array fault alarm,
which can be cleared.
Fault
indicator
Red
Off
The function module is normal.
Blinking
slowly
The function module has an external
fault, which can be cleared.
Steady
on
The function module has an internal fault,
which cannot be cleared.
NOTE
The three indicators are steady on when the power unit of the
function module is upgrading. They return to normal status after the
upgrade is complete.
Lightning rod
Bullet cameras
Dome camera
Pole mounting kit
Function module
Lithium battery
Pole
Cantilever
Cantilever
Bullet cameras
Dome camera
Lithium battery
Connective kit

2
2 Tools
3 Routing Cables Through the Pole
1. Place the pole on a wooden case or a similar object.
2. Route a pull wire.
3. Route cables.
Cables
Inlet
Outlet
Mains AC cable and optical fiber
1
3
Module ground cable
2
3
Camera ground cable
4
5
6
5
7
8
9
8
Dome camera signal cable, power cable, and alarm cable
4
3
9
3
Bullet camera signal cable, and power cable
6
3
7
3
The cables routed from the pole cable hole have a
length of 1.5 m reserved. The cables routed from the
cantilever cable hole have a length of 0.5 m reserved.
The object where the pole is placed should be able to
bear a load above 700 kg.
NOTE

3
4 Installing Cantilevers
1. Install the cantilevers. 2. Adjust the connective kit according to the actual situation to
adjust the relative angle between the two cantilevers.
7 Installing the Function Module and Lithium Battery
6 Installing an Antenna Fastener and Lightning Rod
Wear gloves during installation.
Do not place a module with its bottom against the ground.
Never install a module with power on. Ensure that the angle between a module and the line vertical to the ground is within 10 degrees.
The paint on the module exterior should be intact. If paint has flaked off, repaint the area to avoid corrosion.
NOTICE
5 Installing Cameras and Cables
Installing Cameras
5.1For the camera installation method, see the camera document.
Installing Camera Cables
5.2For the cable connections at the camera side, see the camera document. Reserve the other ends of cables.

4
1. Use a positioning
stickerto mark the
installation position for
the pole mounting kit.
2. Install the pole
mounting kit.
Positioning
sticker
Cable hole
Ensure that the arrow on the top of the pole mounting kit points exactly to the middle
point on the top of the positioning sticker.
There are three types of bolts available for installing the pole mounting kit. Choose
the appropriate type of bolts based on the pole diameter.
NOTE
Bolt
(190 mm)
Bolt (120 mm) Bolt (160 mm)
Pole Diameter
(105–140 mm) Pole Diameter (140–175 mm) Pole Diameter (175–210 mm)
3. Install the function module
hanging kit. 4. Install a function module. 5. Install the lithium battery hanging kit.
6. Install a lithium battery.
If two lithium
batteries are required,
install one above the
other. Install the pole
mounting kit after
using a positioning
sticker at the cable
hole in the upper part
of the pole to mark its
installation position.
For the method, see
steps 1 and 2.
7. (Optional) Install the second lithium battery.
NOTE

5
Installing Ground Cables for Modules
8.1
8 Installing Cables
Route inter-device cables through the pole.
NOTE
Module ground cable
1. Connect ground cables between the function module and lithium batteries. 2. Connect the other end of the module
ground cable to the pole ground bar.
Pole ground bar
Function module Lithium battery Lithium battery
Installing Cables for the Maintenance Compartment
8.2
No.
Cable Hole Silk Screen
Cable Type
Cable Outer
Diameter
1
GE1 - GE2
Optical fiber
6.8±0.3 mm
2
GE3/P&E(++) - GE7 /P&E(++)
P&E network cable
3
GE8/DI
-
4
DO
Dome camera alarm
linkage cable
5
12VDC
Bullet camera power cable
9.3±0.4 mm
6
24VAC
Dome camera power cable
Cable Hole Diameter Requirements
1. Push up the sunshade
until the spring fastener
is stuck gently.
2. Open the maintenance
compartment. 3. Install cables for P&E cameras.
Installation Procedure
Cables for the dome
camera can only be
connected to the
P&E(++) ports.
Bullet camera 1 Bullet camera 2
Dome camera 2
Dome camera 1
NOTE

6
4. (Optional) Install signal cables for non-P&E cameras. 5. (Optional) Install power cables for non-P&E cameras.
Bullet camera 2
Bullet camera 1
Dome camera
Cable distribution terminal
The power cable for the dome camera can only be connected to
the 24V AC port.
One PC500-300G1 can supply power to one non-P&E dome
camera.
Use waterproof tape to protect the cable distribution terminal
and put it inside the pole.
NOTICE
Bullet camera 1 Bullet camera 2
Dome camera 2
Dome camera 1
6. (Optional) Install the door status sensor. 7. (Optional) Install the dome camera alarm linkage cable.
Dome camera
alarm cable
The alarm cables of the two dome cameras can be connected to
the door status sensor. Select one dome camera for connection
according to the actual situation.
NOTICE

7
Battery cable terminal
AC input cable terminal
Preparing Cable Terminals
8.3
8. Install optical fibers. 9. Close the maintenance compartment door.
10.Push down the
sunshade until
the spring
fastener is stuck
gently.
Optical network
This figure uses single-ring networking as an example.
NOTE
NOTE
Battery cables are finished cables. You only need to strip the cables and then insert them into the cable terminals.
AC input cables need to be prepared onsite. Multi-core cables must be used; otherwise, waterproof connectors may be exposed to water
leakage.
Before assembling cables with waterproof connectors, ensure that the connections between the cables and terminals are secure and reliable.
Negative (blue)
Positive (red)
PE (green)
N/L2 (blue)
L/L1 (brown)
Cable Type
Core Cross-
Sectional Area
Cable Outer
Diameter
Battery cable (2-core)
3.3–6 mm2
9.0–14.5 mm
AC input cable (3-core)
1.5–4 mm2
NOTE
Before closing the maintenance compartment
door, check that cables are properly installed.
After closing the door, press the left side of the
maintenance compartment door by hand and
tighten the screws.
Preparing AC Input Cables and Connecting Waterproof Connectors
(Unit: mm)
Flat-head
screwdriver Scale line
Scale line
Preparing Battery Cables and Connecting Waterproof Connectors
Flat-head
screwdriver

8
Installing Power Cables and Signal Cables
8.4
Installing an RJ45 Communications Cable for a Lithium Battery
Ensure that caps and waterproof connectors are installed at all idle ports on the modules.
NOTICE
Connecting Cables Between the Function Module and Lithium Batteries
AC input
Function module Lithium battery Lithium battery
9 Installing Cable Covers
Installing a Cable Cover for the Function Module
9.1

9
Install a Cable Cover for the Lithium Battery
9.2
10Erecting the Pole
1. Check whether the pole needs to be repainted. Repaint the damaged area
of the pole, and then use the crane to hoist the pole to the foundation. 2. Secure the pole to the foundation.
12 Power-On Commissioning
11 Verifying the Installation
1. Check the indicators on the function module and lithium batteries. Ensure that the green indicators are blinking slowly and that the
yellow and red indicators are off.
2. If a problem is found, refer to the alarm definitions in the user manual for troubleshooting.
3. Observe the board indicators in the maintenance compartment.
Powering On Modules
12.1
Normally, The STAT, PWR,
and WIFI indicators on the
EG8P panel are: green.
NOTE
1. Check that the mounting kits are securely installed and all screws are tightened.
2. Check that all cables are reliably connected with correct polarity and there is no short circuit.
3. Check whether any screw holes are not installed with screws. If so, install screws at the holes.
4. Check that all idle cable holes in modules are protected with waterproof caps.

10
Logging In to the Web Server
12.2
1. Use a mobile phone or laptop to search for devices by
searching for WIFI.(Set the laptop to automatically obtain
IP, even after the WIFI will automatically assign an IP
address.)
Changing an NE ID
12.3
1. Choose Configuration > NE Attribute from the Function Tree.
2. Enter the name of the NE in the Name field.
3. Click Apply.
NOTE
Default network element (NE) IP address: 192.168.1.1.
Default user name: szhw. Default password: Changeme_123.
2. Use the browser to enter the NE default IP address,
access the Web Server login page, and enter the values
of User Name, Password, and Verification Code.
3. Click Login.
NOTE
Default WIFI
name: RMn-******.
Default password:
Modify_123.
Changing the NE IP Address
12.4
1. Choose Communication > Communication Parameters from the Function Tree.
2. Configure the communication parameters of the NE.
3. Click Refresh.
During site commissioning, the IP address of the gateway NE needs to be configured in compliance with the external DCN requirements but
other non-gateway NEs use IP addresses that are automatically generated based on NE IDs.
NOTE
Do not use the default NE IP address to access the public network (such as Internet).
The default NE IP address is a temporary address, and is only used for management DCN plug-and-play. The IP address must be
modified in a timely manner.