Huawei UPS5000-S Series User manual

1
Issue: 08
Part Number: 31507820
Date: 2020-11-24
UPS5000-S-(350 kVA-600 kVA)
Quick Guide
1Overview
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
UPS5000-S-400K-SM/FM UPS5000-S-500K-SM/FM
(1) Power modules
(2) Control module
(3) Power distribution
module cover
(4) Maintenance bypass
switch
(5) Bypass module
(6) Mains input switch
(7) Output switch
(8) Bypass input switch

2
UPS5000-S-600K-SM/FM
The UPS5000-S-400K-FM, UPS5000-S-500K-FM, and UPS5000-S-600K-FM are models in full
configuration. The UPS5000-S-400K-SM, UPS5000-S-500K-SM, and UPS5000-S-600K-SM are
models in standard configuration. A UPS in standard configuration has no mains input
switch, output switch, or bypass input switch.
(1) Power modules
(2) Control module
(3) Power distribution module
cover
(4) Maintenance bypass switch
(5) Bypass module
(6) Mains input switch
(7) Output switch
(8) Bypass input switch
UPS Model Weight Dimensions (H x W x D)
UPS5000-S-400K-SM 670 kg
2000 mm x 1200 mm x 850 mm
UPS5000-S-400K-FM 710 kg
UPS5000-S-500K-SM 790 kg
UPS5000-S-500K-FM 830 kg
UPS5000-S-600K-SM 1060 kg 2000 mm x 1400 mm x 850 mm
UPS5000-S-600K-FM 1110 kg

3
The UPS can be installed on channel steel or the floor. Install the UPS based on site requirements.
Floor installation: Determine the UPS mounting holes using the marking-off template, drill
holes, and install the expansion sleeves of the M12x60 expansion bolts in the mounting holes.
Channel steel installation: Ensure that the distance between the outer surfaces of two pieces
of channel steel is 800 mm and secure the channel steel to the floor using expansion bolts.
Huawei does not provide channel steel or expansion bolts used for securing channel steel. The
customer should purchase channel steel (recommended width: 50 mm or more) and
expansion bolts.
1. Before installation, read the user manual carefully to get familiar with product information
and safety precautions.
2. Use insulated tools during installation and operation.
3. Only Huawei engineers or engineers certified by Huawei are allowed to install, commission,
and maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the
resulting UPS faults are beyond the warranty scope of Huawei.
4. This document describes how to install a single UPS. For details about how to install parallel
systems, contact Huawei technical support.
Determining the UPS Installation Position
2.1
Installing the UPS
2

4
UPS5000-S-400K/500K-SM/FM
UPS5000-S-600K-SM/FM
Unit: mm
A: mounting holes on the channel steel
B: mounting holes on the floor
•Floor mounting: Use eight M12x60 expansion bolts to secure the cabinet to the ground.
•Channel steel mounting: Use eight M12x60 common bolts to secure the cabinet to channel
steels.
Securing the UPS
2.2

5
(1)
Cabinet mounting holes (ground installation mode)
(2) Cabinet mounting holes (channel steel installation mode)
3Connecting Cables
Installing the Front, Rear, Left, and Right Anchor Baffle Plates
2.3
1. This document describes cable routing by removing the top cover when there are two mains
inputs.
2. In the case of single mains, you do not need to connect bypass input power cables and
remove short-circuit copper bars.

6
UPS Cable Connection Reference
3.1
Installing Cables
3.2
•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps
may ignite and cause personal injury or device damage.
•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets
and surrounding environment clean and tidy.
•You need to prepare terminals onsite. The stripped length of the copper wire should be the
same as that of the part of the terminal that covers the conductor.
The cabling route is for reference only. Connect cables based on site requirements.

7
2. Remove the top cover from the
cabinet based on cable routes and
dimensions.
1. Open the front door of the bypass cabinet, and
remove front power distribution covers
(UPS5000-S-500K-FM is used as an example).
3. Remove the rear cover from the bypass
cabinet, and then remove the connecting
copper bars between the mains input
terminals and bypass input terminals. (If
the mains input and bypass input share a
power source, skip this step.)
UPS5000-S-500K-SM/FM
UPS5000-S-400K-SM/FM
Scenario 1: Routing Cables from the Top

8
UPS5000-S-600K-SM/FM 4. Connect the ground cable to the UPS.
6. Connect output power cables.
5. Connect mains input power cables.

9
7. Connect bypass input power cables. 8. Connect battery cables.
9. Connect the signal cable.
The figure shows the signal cable
routing and is for reference only.
Connect the cable based on the actual
situation.

10
Scenario 2: Routing Cables from the Bottom
For the screw specifications and torque
used for connecting cables in a bottom
cable routing scenario, refer to the top
cable routing scenario. This section only
shows the cable routes in the bottom
cable routing scenario.
1. Remove the cable covers from the bottom of
the cabinet, drill holes in the covers, attach
grommet strips to the hole edges for
protecting cables, and reinstall the cable
covers.
2. Connect power cables and signal cables.
4Installation Verification
1. Check that there is no foreign matter in the cabinet.
(1) Switches
(2) Mains input wiring
copper bars
(3) Battery input
wiring copper bars
(4) Output wiring
copper bars
(5) Bypass input wiring
copper bars
(6) Cabinet rear