Huawei AP6510DN-AGN User manual

AP6510DN-AGN Outdoor Wireless LAN Access Point
Quick Start Guide
HUAWEI TECHNOLOGIES CO., LTD.

Huawei Technologies Co., Ltd.
Address: Administration Building,Huawei Technologies Co.,
Ltd.,Bantian,Longgang District,Shenzhen,People’s Republic of China
Postcode: 518129
Website: http://www.huawei.com
Email: [email protected]
Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of
Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or
part of the products, services and features described in this document may not be within the purchase scope or the usage
scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are
provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation
of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document
do not constitute the warranty of any kind, express or implied.
1

Change History
Changes between document issues are cumulative. Therefore，the latest document issue contains all the
Changes in previous issues.
Change in Issue 01 (2012-05-30)
Initial commercial release.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Description
NOTE
CAUTION Indicates a potentially hazardous situation, which if not avoided, could
result in equipment damage, data loss, performance degradation, or
unexpected results.
Provides additional information to emphasize or supplement important
points of the main text.
2

Please download the detailed product documents from "http://support.huawei.com/support/".
The detailed path is as follows: Technical Support->Documentation->Access Network -> WLAN ->WLAN -> Product
Documentation -> AP6510DN.
AP6510DN-AGN
Quick Start Guide
技术支持
Before performing Installation, confirm that the installation accessories and tools are available.
Installation tools: Technical Support
Huawei Technologies Co., Ltd.
Address:Administration Building,Huawei
Technologies Co., Ltd.,Bantian,Longgang
District,Shenzhen,People’s Republic of China
Postcode:518129
Email:[email protected]
Website:http://www.huawei.com
Phillips
screwdriver Hammer
Combination
pliers
Maker
Flat-head
screwdriver Diagonal
pliers Adjustable
wrench
Utility knife ESD
gloves COAX
crimping toolMeasuring
tape
Wire
stripper Cable
cutter RJ45
Crimping tool Multimeter
Level
Vacuum
cleaner Network
cable tester
Installation
suite Expansion
bolt M4X12 hexagon
socket head cap
screw
Hoop Hammer
drill
Hex key
Installation accessories:
Device Overview
Packing List
Unpack the equipment. Ensure that all items listed in the package list are included in the shipment. If any item is missing,
contact the supplier.
Ports and indicators
5G antenna port
6
72.4G antenna port
Connected to the feeder
Connected to the feeder
Item Description
SN
Product functions
3
1
2
3
4
1
1
4
Item Quantity Unit
AP device PCS
PCS
PCS
Installation suite
1PCS
Network port connector
52
Expansion bolt PCS
62
M4X12 hexagon socket head cap screw
PCS
10 1
Item Quantity Unit
PCS
Warranty card
Certificate of Conformance
Hoop
71PCS
Quick Start Guide (including the
printed packing list)
81PCS
9
Toxic or Hazardous Substance &
Elements Declaration
1PCS
1234 5
Item Description
SN
SYS
Wireless
Default
1
SYS status indicator.
2
3
4
5
Link
ETH/POE
port
Link status indicator.
Wireless status indicator.
Used for Ethernet connections.
Press and hold down the Reset button for 3 seconds
to restore the factory settings and restart the AP.
6 677
6mm drill
bit

Installing an AP
●Select an appropriate installation position and leave space above and around the device for cooling air circulation.
●Outdoors APs are used for hotspot coverage and often installed against walls or poles. The pole diameter is 30 to 114 mm.
AP6510DN dimensions (unit: mm) without a backplane support Recommended AP6510DN installation space (unit: mm)
●Installing the AP6510DN against a Wall:
330 83
306
Hexagon
socket head
cap screw
Field strength
场强示意
1. Fix the wall-mounting bracket to the wall, adjust the
installation position, and use the marker, level, and
measuring tape to mark the drilling positions where
expansion bolts are installed.
2. Use #8 drill bit to drill 35–40 mm deep holes in the drilling
positions and install expansion bolts. Screw the nut into the
expansion tube, hammer the expansion bolt into a hole until
the flat washer is flattened against the wall, and remove the
nuts, spring washer, and flat washer in order.
Flat washer
Spring washer
Nuts
3. Use four M4*14 hexagon socket head cap screws to fasten the wall-mounting bracket to the AP.
4. Pinch the wall-mounting bracket on the expansion
bolts, and fasten the Flat washer, spring washer, and
nuts in order.
5. Slide the AP into the wall-mounting bracket to complete
installation.
4
64mm
37mm

Installing an AP
上电调试
3
●Installing the AP6510DN against a vertical pole:
Field strength
场强示意
NOTE
Lock hole
Security
lock
1. Determine the AP installation position, slide the hoop
through the hole of the wall-mounting bracket and attach
it to the pole, And use the screwdriver to secure screws
on the hoop.
2. Slide the AP that has the connector fastened into the wall-
mounting bracket.
●The procedure for installing the AP6510DN against a horizontal pole is similar to the procedure for installing the AP6510DN
against a vertical pole.
●Installing the Security Lock
To prevent unauthorized personnel from moving the AP, lock the AP. The preceding figure shows the security lock. The
carrier should purchase the security lock and determine the position for installing the security lock.
5

Installing Cables
●AP6510DN external cable arrangement drawing
3. Put the network cable through the hole on the waterproof PG connector.
a b c d
4. Connect the RJ45 connector to the AP and secure the waterproof PG connector, as shown in figures b, c, and d.
a b c d
Ensure that the RJ45 connector is correctly connected to the AP. Otherwise, the network cable may be damaged.
Before removing the network cable, remove the waterproof PG connector, and then remove the RJ45 connector from
the AP.
Waterproof PG connector
CAUTION
●Connecting network cables
1. Use a shield straight-through cable. Cut the cable of proper length based on the distance between the AP and the PSE
device, peel the insulation on both ends of the network cable, and crimp the wires to RJ45 connectors.
2. Make a network cable onsite according to the following pin assignment. Otherwise, the communication quality is
affected even if devices can be connected.
X1 Pin
1
2
3
4
5
6
7
8
X2 Pin
1
2
3
4
5
6
7
8
Wire Color
White and orange
Orange
White and green
Blue
White and blue
Green
White and brown
Brown
Feed line
Ground cable
Network cable
Feed line
Feed lineFeed line
6

Installing Cables
●Connecting the feed line
1. The outdoor AP's antenna ports already have 5 KA surge protection capability. Generally, no surge protection devices
need to be installed; therefore, the antenna cables are directly connected to the AP's antenna ports.
2. If higher surge protection capability is required, the customer can purchase a surge protection device. When installing the
surge protection device, ensure that it is connected to a ground cable.
a
Waterproof adhesive tape
Ground cable
NOTE
Surge
protection
device
c
b
Waterproof
adhesive
tape
Feed line
Feed line
●Wrap the feed line using one-layer PVC black insulation tape, three-layer waterproof adhesive tape, and then three-layer
PVC black insulation tape.
●Stretch the waterproof adhesive tape evenly and ensure that the upper layer of the tap overlaps 1/2 of the lower layer.
Each layer should be attached tightly.
●Wrap the three-layer waterproof adhesive tape from bottom to up, from up to bottom, and from bottom to up in order.
Connecting the ground
bar
●Connecting the ground cable
●Cut the cable of proper length, and select 6-M4 OT terminal for the AP and 6-M6 OT terminal for the ground bar.
7
Keep the screw properly and install it again after pressing the Reset button.
CAUTION
●Pressing the Reset Button
The Reset button on an outdoor AP is protected by a waterproof screw. Before pressing the Reset button, remove the
waterproof screw.

Installing Cables
●Requirements for Laying Out Cables
● Requirements for laying out power cables
1. The power cable must be separated from ground cables and signal cables.
2. If multiple power cables are installed, you must bind the power cables.
3. The routing of power cables must meet engineering design drawing requirements.
4. If the power cable length is insufficient, replace the power cable. The power cable must be complete and cannot
have splices or welding points.
● Requirements for laying out ground cables
1. All ground cables must be connected to a ground bar.
2. The ground cable cannot be led in aerially, but buried in the earth or arranged indoor.
3. Both ends of the external conductor of the coaxial cable and those of the insulation of the shielded cable should
have good electric contact with the metal shell of the equipment they connect to.
4. Ground cables must be separated from signal cables to reduce interference between them.
5. Do not add any switch or fuse on the ground cable.
6. Do not use another device for an electrical connection with the ground cable.
7. All metal components in the shell must be securely connected to the ground cable.
● Requirements for laying out optical fibers
1. Do not press optical fibers forcibly or crush optical fibers with force. Leave sharp objects away from optical fibers
to prevent damage to optical fibers.
2. Coil up redundant optical fibers round specialize devices such as the splice tray.
3. Coil optical fibers gently and do not break them.
4. Cover optical fiber connectors with protective caps.
8

Power-on
2连接线缆
Technical Specifications
Power on the AP6510DN and check the indicator status to determine the system
running status.
NOTE
SYS Wireless
Link Description
Information
Type
Steady green
Steady red
Blinking green
Blinking once
every 2s
Running status
The indicator is
steady green if no
data is
transmitted. The
indicator blinks
green more
quickly when
more packets are
transmitted.
Off
Off
Off
Off
Blinking green
Off
Off
Off
Off
The system is working properly.
The system fails to load the DRAM or system software.
The device is being started.
Blinking once
every 2s
The system is working properly, but the Ethernet is not
connected and radios or all VAPs are disabled.
The system is working properly, but the Ethernet is not
connected. The wireless indicator blinks more quickly as more
packets are received on the 2.4 GHz air port.
Off The system is working properly, but the Ethernet is not
connected and radios or all VAPs are disabled.
Blinking yellow The system is working properly, but the Ethernet is not
connected. The wireless indicator blinks more quickly as
more packets are received on the 5 GHz air port.
The system is working properly, but the Ethernet is not
connected. STAs at 2.4 GHz and 5 GHz are connected.
Blinking green The system is working properly, but the Ethernet is not
connected. The wireless indicator blinks more quickly as more
packets are received on the 2.4 GHz air port.
Blinking yellow The system is working properly, but the Ethernet is not
connected. The wireless indicator blinks more quickly as
more packets are received on the 5 GHz air port.
The system is working properly, but the Ethernet is not
connected. STAs at 2.4 GHz and 5 GHz are connected.
83mm×255mm×255mm
2.2Kg
Item Description
Operating temperature –40°C to +60°C
Storage temperature
0% to 100%
Relative humidity
Altitude
70 kPa to 106 kPa
Weight
Dimensions (H x W x D)
–40°C to +70°C
Pressure
PoE power supply -48V
–60 m to 4000 m When the altitude is
between 1800 m and 4000 m, the
operating temperature decreases by
1°C each time the altitude increases by
220 m.
9
Blinking green and
yellow alternately
Blinking green and
yellow alternately