Huawei Quidway W1000 Series User manual

Quidway W1000 Series Wireless
Access Device WA1003A Wireless
ADSL Access Point
Quick Installation Guide
All manuals and user guides at all-guides.com
all-guides.com

Huawei Technologies Proprietary
Copyright© 2005 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this document may be reproduced or transmitted in any
form or by any means without prior written consent of Huawei
Technologies Co., Ltd.
Trademarks
, HUAWEI, SmartAX are trademarks of Huawei Technologies Co.,
Ltd.
All other trademarks mentioned in this manual are the property of their
respective holders.
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document don't constitute the warranty of
any kind, express or implied.
All manuals and user guides at all-guides.com

Huawei Technologies Proprietary
i
Table of Contents
WA1003A QUICK INSTALLATION GUIDE ................... 1
Overview .........................................................................................1
Preparations....................................................................................4
Connecting WA1003A.....................................................................5
Quick Troubleshooting ....................................................................7
Safety Concerns............................................................................10
Technical Specifications ...............................................................12
All manuals and user guides at all-guides.com

Huawei Technologies Proprietary
1
WA1003A Quick Installation Guide
Use this Quick Installation Guide to establish your ADSL
connection quickly and access the Internet.
Note: If you need to configure the device, ask your ISP for
necessary information and guidance.
Overview
The following summarizes the necessary information to install
WA1003A:
zOverview
zPreparations
zConnecting WA1003A
zQuick Troubleshooting
zSafety Concerns
zTechnical Specifications
Overview
WA1003A combines high-speed ADSL connection technology,
TCP/IP routing and 802.11b/g wireless connectivity in one
compact unit.
All manuals and user guides at all-guides.com

Huawei Technologies Proprietary
2
Figure1 Rear panel
Description of buttons/ports in rear panel as below (From left to
right):
Buttons/Ports Description
12V/AC 1.2A,
12V/DC1.25A: The port for AC power adapter.
Reset
The WA1003A may be reset to the original
factory default settings if you press the
reset button for a few seconds while the
device is powered on.
Power Press the button after the power adapter is
connected correctly to power on the device.
Ethernet You can establish one Ethernet
connections by using Ethernet port.
USB
If your computer has an available USB port,
you can connect WA1003A to this USB port
through a USB cable.
ADSL
Plug one end of the cable into the ADSL
port (RJ-11 receptacle) on the rear panel of
WA1003A and insert the other end into the
RJ-11 wall socket.
Antenna: Screw-on antenna, for 802.11b/g wireless
connection.
All manuals and user guides at all-guides.com

Huawei Technologies Proprietary
3
In order to observe the LEDs, place WA1003A where it is easily
moved.
Figure2 Front panel
The LED Indicators is described as follows (From left to right):
Number LED
Indicators Description
1 Power
zSolid green indicates the device is
powered on.
zNo light indicates the device is
powered off.
2 Status
zSolid green indicates power on self-
test (POST) is in progress.
zBlinking green indicates the
connection status is stable.
zSolid green after the POST indicates
the system fails and the device needs
reboot.
3 ADSL:
Link/Act
zSolid green indicates a valid ADSL
connection. It is on after the ADSL
negotiation process is settled.
zBlinking green indicates activity on
the WAN (ADSL) interface.
All manuals and user guides at all-guides.com
all-guides.com

Huawei Technologies Proprietary
4
Number LED
Indicators Description
4 Wireless:
Link/Act
zSolid green indicates a valid WLAN
connection.
zBlinking green indicates activity on
the WLAN interface.
5 USB:
Link/Act
zSolid green indicates a valid USB
connection.
zBlinking green indicates activity on
the USB interface.
6-9 LAN
1: Link/Act
zSolid green light indicates a valid link
on startup.
zBlinking green indicates data is
currently passing through the
Ethernet port.
Preparations
Dialing Application
Under the access mode of PPPoE, if the built-in dialing function
of WA1003A is disabled, you can install additional dialing
application on your computer to connect to the ISP’s network.
Splitter
Splitter can reduce disturbance signals in the telephone line.
WA1003A needs a separate splitter. An external splitter has
three ports.
zLINE: Connecting to the phone jack.
All manuals and user guides at all-guides.com

Huawei Technologies Proprietary
5
zPHONE: Connecting to the telephone sets.
zMODEM: Connecting to the ADSL port of WA1003A.
Ethernet NIC
Computer is connected to WA1003A through the Ethernet port
on WA1003A. Ensure your computer is configured with NIC
adapter as well as Ethernet port. Besides, be sure to enable the
TCP/IP protocol for your operating system (OS).
User Name and Password
For PPP connections you must obtain the user name and
password from your ISP.
Connecting WA1003A
Note: If you want to connect one or more telephones, a
splitter is needed to work between telephones and the
line from the phone Jack.
Note: Place WA1003A in a location with enough space that
you can easily connect the ports on the rear panel.
The device should be near the computer for you to
easily view the LED indicators on the front panel. To
avoid WA1003A to be overheated by the bad
condition of emission, leave enough space around
WA1003A while the device is working.
You are now ready to connect WA1003A. Follow these steps:
All manuals and user guides at all-guides.com

Huawei Technologies Proprietary
6
1. Connect the ADSL line - Plug one end of the twisted-pair
phone cable into the splitter and insert the other end into
the wall socket. Use another phone cable to connect the
splitter with the ADSL port on the rear panel of WA1003A.
(1) Computer (2) Phone (3) RJ-45 Ethernet Cable
(4) RJ-11 Tel Cable (5) RJ-11 Tel Cable (6) Splitter
(7) WA1003A (8) RJ-11 Tel Cable (9) Phone Jack
Figure3 ADSL connection
2. Connect the power adapter - Use the power adapter
supplied and plug it into a suitable power source. You
should see the Power LED indicator light up and remain lit.
3. Connect WA1003A to your computer - Use the Ethernet
cable provided to connect WA1003A with your computer or
laptop through the 10/100Base-TX Ethernet ports. You can
All manuals and user guides at all-guides.com

Huawei Technologies Proprietary
7
also connect WA1003A to your computer through USB port
or 802.11b/g wireless connection.
When the LAN Link/Act LED of WA1003A is on, it indicates
the connection between WA1003A and your PC is okay.
Note: Use cross-over cable to connect WA1003A with the
uplink port of a switch or hub.
Note: The attached Ethernet cable in the packing box is a
straight-through cable. Make sure that the cable
connecting the LAN to WA1003A does not exceed
100 meters.
Quick Troubleshooting
Trouble Solution
The indicator
of power
supply is not
on
Make sure the connection of power supply is
correct.
Make sure the switch of power supply is
turned on.
Make sure the output of power supply is
correct.
All manuals and user guides at all-guides.com