Hubbell GAI-TRONICS HUBBCOM GRC600SS User manual

Pub. 42004-538B
G A I - T R O N I C S ®
A H U B B E L L C O M P A N Y
HUBBCOM™ Remote and Stainless-
Steel Remote Stations
TA B L E O F CO N T E N T S
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA
610-777-1374 ◼800-492-1212 ◼Fax: [phone]
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
General Information.......................................................................................................................2
Security Hardware..................................................................................................................................2
Important Safety Instructions................................................................................................................3
Installation ......................................................................................................................................4
GRC600....................................................................................................................................................4
Surface Mounting (Indoor Installations Only)......................................................................................4
Weatherproof Two-Gang Electrical Box Mounting (Exterior Installations) ........................................5
GRC600SS...............................................................................................................................................5
Flush-Mount Installations.....................................................................................................................5
Surface Mount Installations with GAI-Tronics Model 236 Series or Model 238-001 Enclosure.........5
Wiring......................................................................................................................................................6
Ethernet/POE ........................................................................................................................................6
Local Power (Optional).........................................................................................................................7
Input Contacts.......................................................................................................................................8
Wiegand Data/Output Contact..............................................................................................................8
USB1 and USB2...................................................................................................................................9
Configuration..................................................................................................................................9
Service and Spare Parts..................................................................................................................9
Reference Documentation ..............................................................................................................9
Specifications ................................................................................................................................10
Electrical................................................................................................................................................10
User Interface........................................................................................................................................10
Mechanical.............................................................................................................................................10
Environmental.......................................................................................................................................11
Approvals.......................................................................................................................................11

Pub. 42004-538B
GAI-TRONICS®
A HUBBELL COMPANY
HUBBCOM™ Remote and Stainless-
Steel Remote Stations
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA
610-777-1374  800-492-1212  Fax: [phone]
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
General Information
This manual covers Model GRC600, HUBBCOM Remote Station and Model GRC600SS, Stainless Steel
HUBBCOM Remote Station. Both remote stations function as access control devices and/or as remote
audio/video monitoring stations. They will work in standalone configurations or as part of a HUBBCOM
system. Use the GUDA (GAI-Tronics Universal Device Application) to configure specific features for
the remote station. See the GAI-Tronics website at https://www.gai-tronics.com for system
specifications, warranty information, and the GUDA.
Security Hardware
The HUBBCOM remote stations described in this manual are vandal resistant. The front covers are
attached to the mounting plate/enclosure with security screws. Use a GAI-Tronics Model 233-001
Security screwdriver or Torx T-25 security head tip (sold separately) to install the Model GRC600SS
station. Use a Torx T-10 security head screwdriver to install the Model GRC600 station.
Figure 1. HUBBCOM Remote Statio
n
Stainless Steel HUBBCOM Remote Statio
n

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 3 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
Important Safety Instructions
•Read, follow, and retain instructions—All safety and operating instructions should be read and
followed before operating the unit. Retain instructions for future reference.
•Heed warnings—Adhere to all warnings on the unit and in the operating instructions.
•Attachments—Attachments not recommended by the product manufacturer should not be used, as
they may cause hazards.
•Servicing—Do not attempt to service this unit by yourself. Opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
ATTENTION
—Install equipment without modification and according to all applicable local,
national, and international electrical codes. North America—Consult the
National Electrical Code (NFPA 70), Canadian Standards Association (CSA
22.1), and local codes for specific requirements regarding your installation.
Class 2 circuit wiring must be performed in accordance with the NEC.
These enclosures must be installed by trained, qualified, and competent personnel. Installation must
comply with state and national regulations, as well as safety practices for this type of equipment.
WARNING
—Use only 12 or 24 V dc power supplies that conform to UL/CSA/CE Class II,
Double Insulated supplies with over voltage and short circuit protection. Use
only a dc source with a 50-watt maximum output or fuse the supply with a 2-
amp fuse. EMI standards to Class B.
•Onderhoud—Probeer dit apparaat niet zelf te repareren. Het openen of verwijderen van afdekkingen
kan u blootstellen aan gevaarlijke spanning of andere gevaren. Laat alle onderhoud over aan bevoegd
onderhoudspersoneel.
•HUBBCOM Smart Controllers zijn alleen bedoeld voor gebruik binnenshuis.
AANDACHT
—Gebruik alleen 12 oder 24 VDC-voedingen die voldoen aan UL/CSA/CE Klasse
II, dubbel geïsoleerde voedingen met overspanning en kortsluitbeveiliging.
Gebruik alleen een DC-bron met een maximale output van 50 W of fuseer de
voeding met een 2-ampère zekering. EMI-normen voor klasse B.
•Dépannage—N'essayez pas de réparer cet appareil vous-même. Ouvrir ou retirer les capots peut vous
exposer à des tensions dangereuses ou à d'autres dangers. Confiez toute réparation à un personnel
qualifié.
•Les contrôleurs intelligents HUBBCOM sont conçus pour une utilisation en intérieur uniquement.
ATTENTION
—Utilisez uniquement des alimentations 12 ou 24 Vcc conformes à UL/CSA/CE
Classe II, des alimentations à double isolation avec protection contre les
surtensions et les courts-circuits. Utilisez uniquement une source cc avec une
sortie maximale de 50 watts ou fusionnez l’alimentation avec un fusible de 2
ampères. Normes EMI à la classe B.
•Manutenzione—non tentare di riparare l'unità da soli. L'apertura o la rimozione dei coperchi
potrebbero esporre a tensioni pericolose o altri rischi. Rivolgersi a personale qualificato per
l'assistenza.
•Gli HUBBCOM Smart Controller sono progettati esclusivamente per uso interno.

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 4 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
AVVERTIMENTO
—Utilizzare solo alimentatori a 12 o 24 V cc conformi a UL/CSA/CE Classe
II, alimentatori a doppio isolamento con protezione da sovratensione e
cortocircuito. Utilizzare solo una fonte di corrente continua con un'uscita
massima di 50 watt o collegare l'alimentazione con un fusibile da 2 A.
Standard EMI per la classe B.
• Mantenimiento—no intente reparar esta unidad por sí mismo. Abrir o quitar las cubiertas puede
exponerlo a un voltaje peligroso u otros peligros. Remita todo el servicio a personal de servicio
calificado.
• Los controladores inteligentes HUBBCOM están diseñados para uso en interiores solamente.
ADVERTENCIA
—Utilice solo fuentes de alimentación de 12 o 24 V cc que cumplan con
UL/CSA/CE Clase II, fuentes con doble aislamiento con sobretensión y
protección contra cortocircuitos. Utilice solo una fuente de CC con una
salida máxima de 50 vatios o fusione la fuente con un fusible de 2 amperios.
Estándares EMI a Clase B.
Installation
Record the MAC address of the GRC600 or GRC600SS Remote Station before installation. Use the
MAC address to configure the unit in the GUDA (including giving it a meaningful name).
GRC600
The HUBBCOM Remote Station is surface mounted on a wall (indoor installations only) or on a
(customer provided) weatherproof metallic two-gang electrical box (outdoor installations).
Surface Mounting (Indoor
Installations Only)
1. Drill two holes through the mounting plate
at the drill points (see Figure 1) and drill
corresponding holes in the mounting
surface.
2. Secure the mounting plate to the wall
using (customer supplied) hardware.
3. Feed the Ethernet cable and all additional
cables through the hole in the mounting
plate.
4. Complete all necessary cable terminations
(see the Wiring section).
5. Assemble the front cover to the mounting
plate and secure it with the two included
security screws.
6. Tighten the screws to 3–5 in∙lb.
Figure 2. HUBBCOM Remote Station Back Plate

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 5 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
Weatherproof Two-Gang Electrical Box Mounting (Exterior Installations)
NOTE:The HUBBCOM Remote Station is mounted on a (customer supplied) weatherproof metallic
two-gang electrical box.
1. Install the two-gang electrical box in or on the mounting surface.
2. Place one of the supplied conduit box gaskets between the electrical box and the mounting plate.
3. Feed the Ethernet cable and all additional cables into the electrical box and through the gasket and
mounting plate.
4. Assemble the mounting plate to the electrical box using the supplied #6-32 x 5/8-inch flat head
screws (see Figure 2).
5. Complete all necessary cable terminations (see the Wiring section).
6. Assemble the front cover to the mounting plate and secure with the two included security screws.
7. Tighten the screws to 3–5 in∙lb.
GRC600SS
Flush mount the stainless steel HUBBCOM remote station in a wall or communication tower using the
included backbox or surface mount it with a GAI-Tronics Model 236 Series or Model 238-001 Stainless-
Steel Surface-Mount Enclosure (sold separately).
Flush-Mount Installations
Use the supplied back box for flush mount installations or for installation in a GAI-Tronics Model 234
Series Communication Tower.
1. Remove tapered plugs from the rear cable entry holes in the backbox.
2. Feed the Ethernet cable and all additional cables through the two holes in the backbox.
3. Mount the back box to the structure using appropriate hardware (see Figure 3 for cutout dimensions).
4. Complete all cable terminations (see the Wiring section).
5. Secure the unit to the backbox mounting flanges using the six security screws with washers provided.
6. Tighten the screws to 10–12 in∙lb.
Surface Mount Installations with GAI-Tronics Model 236 Series or Model 238-001
Enclosure
1. Install the surface-mount enclosure.
Refer to Pub. 42004-285 for the Model 236 Series or Pub. 42004-434 for the Model 238-001
backboxes for installation instructions (see the Reference Documentation section).
2. Remove and discard the backbox installed on the stainless-steel remote station.
3. Complete all cable terminations (see the Wiring section).
4. Secure the unit to the surface-mount enclosure using the six security screws and washers provided.
5. Tighten the screws to 10–12 in∙lb.

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 6 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
Figure 3. Cutout Detail for GRC600SS
Wiring
HUBBCOM Remote stations are equipped with terminal blocks that accept 20–26 AWG wires (see
Figure 4).
NOTE: Model GRC600 only: Two clamp-on ferrite cores are supplied with the Model GRC600 Remote
Station; one white, one black. Run all wires terminating to terminal blocks TB1, TB2, and/or
TB3 through the black ferrite core. Double wrap all the Ethernet wires around the white ferrite
core. Install the clamp-on ferrite cores as close as possible to the terminal blocks. Do not use
the ferrite cores with the Model GRC600SS Remote Station.
Ethernet/POE
Terminate the Ethernet cable to RJ-45 jack J1:
1. Model GRC600 Only: Double wrap the Ethernet cable with the white ferrite core as close as possible
to the RJ-45 jack.
2. Insert the RJ-45 plug into the RJ-45 jack J1, on the PCBA.

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 7 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
Figure 4. HUBBCOM Remote Station PCBA
Local Power (Optional)
Terminate the input power cable at terminal block TB2 if PoE (power over Ethernet) is not available:
1. Install appropriately sized ferrules onto the wire ends.
2. Model GRC600 Only: Install the black clamp-on ferrite core around all wires terminating to TB2 as
close as possible to the terminal block.
3. Insert each wire into the correct terminal (See Table 1).
Table 1. Optional Local Power Termination
Terminal Block TB2
Purpose Pin Label
Shield 1 SHLD
Power − 2 −
Power + 3 +
Shield 4 SHLD

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 8 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
Input Contacts
Terminate the input contacts at terminal block TB3:
NOTE:Shielded cable must be used for outdoor installations when using Wiegand/clock data.
1. Install appropriately sized ferrules onto the wire ends.
2. Model GRC600 Only: Install the black clamp-on ferrite core around all wires terminating to TB3 as
close as possible to the terminal block.
3. Insert each wire into the correct terminal (See Table 2).
Do NOT connect the cable shield to ground at the remote station.
Table 2. Input Terminations—Terminal Block TB3
Purpose
Pin
Label
shield
1
SHLD
input four
2
IN4
ground
3
G
input three
4
IN3
shield
5
SHLD
input two
6
IN2
ground
7
G
input one
8
IN1
Wiegand Data/Output Contact
Terminate the output connections at terminal block TB1:
1. Install appropriately sized ferrules onto the wire ends.
2. Model GRC600 Only: Install the black clamp-on ferrite core around all wires terminating to TB1 as
close as possible to the terminal block.
3. Insert each wire into the correct terminal of terminal block TB1 (See Table 3).
Table 3. Data/Output Contact Terminations—Terminal Block TB1
Purpose
Pin
Label
shield
1
SHLD
Wiegand/clock data
2
DG
Wiegand/clock data
3
D1
Wiegand/clock data
4
D0
shield
5
SHLD
output ground
6
G
open collector
7
OC
output power
8
+5V

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 9 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
USB1 and USB2
Terminate the USB cables at USB ports J2 and J3:
1. Install USB-A plugs onto the wire ends.
2. Insert the USB cables into the USB ports.
3. Model GRC600 Only: Install the black clamp-on ferrite core around the cable as close as possible to
the installed USB plugs.
Configuration
Configure HUBBCOM remote stations using the GUDA (GAI-Tronics Universal Device Application).
Refer to Pub. 42004-531 for complete instructions to configure the remote station (see the Reference
Documentation section).
1. Launch the GUDA software.
2. Click the refresh button next to the SELECT NETWORK INTERFACE field to refresh the list of active
network adapters to perform a network discovery for devices.
3. Use the drop-down list to select a different network if the HUBBCOM™device is on a different
network accessed through another network adapter.
4. Click the FIND DEVICES button to locate available HUBBCOM™devices.
Unconfigured devices appear with the factory default name: HUBBCOM-MAC-ADDRESS.
5. Double click the desired device or select it and click CONNECT to access the device’s configuration
pages.
6. Enter a meaningful device name.
7. Click the APPLY button.
Service and Spare Parts
Contact a regional service center for assistance if the equipment requires service or spare parts. An RA#
(return authorization number) will be issued if service is required. Equipment must be shipped prepaid to
GAI-Tronics with an RA# and a purchase order number. Repairs or a replacement are made in
accordance with GAI-Tronics’ warranty policy if the equipment is under warranty. Please include a
written explanation of all defects to assist our technicians in their troubleshooting efforts. Call 800-492-
1212 inside the USA or 610-777-1374 outside the USA for help with identifying the nearest regional
service center.
Reference Documentation
GAI-Tronics publications are located on the GAI-Tronics website at https://www/gai-tronics.com.
GAI-TRONICS Universal Device Application .............................................................................42004-531
236-001 Series Surface Mount Enclosure......................................................................................42004-285
238-001 Series Stainless Steel Surface Mount Enclosures............................................................42004-434

Pub. 42004-538B
HUBBCOM™ Remote and Stainless-Steel Remote Stations Page 10 of 11
P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-538B.docx
06/20
Specifications
Electrical
Power Consumption
Network Power.....................................................................................................PoE/PoE+, IEEE 802.23af
Local Power.......................................................................................................................12–24 V dc, 10 W
Ethernet
Cable............................................................................................................................. Category 5e or better
Speed....................................................................................................................................up to 1000 Mbps
USB (Quantity 2)
Cable..................................................................................................................................................shielded
Speed................................................................................................................................................. USB 2.0
Card Reader Interface
Cable....................................................................................................................3-wire, untwisted, shielded
Protocol.............................................................................................................................................Wiegand
Generic Inputs/Outputs
Inputs ........................................................................................................................................ 4, dry contact
Outputs................................................................................................. 1, open collector, 125 mA maximum
User Interface
GRC600
Activation Control ................................................................................................pushbutton with LED ring
Speaker Audio.................................................................................................................................. 8 Ω, 2 W
Microphone.......................................................................................................................digital microphone
Status Indication......................................................................................................................... 3 Color LED
RFID Card........................................................................................Wiegand 26-bit H10301 proximity card
NFC Card.....................................................................................NXP MiFare Classic 1K EV1 ISO14443A
NXP MiFare DESFire 4K EV1
NXP MiFare Ultralight EV1
GRC600SS
Activation Control ...............................................................................................pushbutton with LED ring
Speaker Audio.................................................................................................................................. 8 Ω, 2 W
Microphone.......................................................................................................................analog microphone
RFID Card........................................................................................Wiegand 26-bit H10301 proximity card
NFC Card.....................................................................................NXP MiFare Classic 1K EV1 ISO14443A
NXP MiFare DESFire 4K EV1
NXP MiFare Ultralight EV1
Mechanical
GRC600
Construction..............................................................................................................black engineered plastic
Dimensions ...........................................................6.73 H × 5.19 W × 1.57 D in (131.9 × 171.0 × 39.9 mm)
Weight.................................................................................................................................... 1.2 lb (0.54 kg)