Hubbell KIM Lighting SCARAB Accent Series User manual

SCARAB™AccentSeries - KLV710 / KLV715 Installation Instructions
P.O. Box 60080 • 16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 •FAX [phone]
Revision 10/14/11 EC 111014007 Status 10 Part No. 95588
Tools Required: Phillips Screwdriver B” Hex Wrench Flatblade Screwdriver
Adjustable Wrench Silicone Grease
Fixture Cable
Shield
Gasket
Lens
1. Tighten coupling onto
mounting device. (Consult
Kim Landscape Catalog for
mounting device options.)
2. Install fixture onto coupling.
Note: Kim "KLV" Mounting
Options can be installed
before fixture is installed.
3. Remove lens and shield. Install lamp of type
and wattage shown on fixture label and chart
below. Do not exceed maximum wattage. Coat
screws with silicone grease.
INSTALLATION INSTRUCTIONS: Make certain the electrical supply is OFF before starting installation.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS: Do not overdrive fixtures with greater
than 12 volts or fixture over-heating and short lamp life will occur. Do not overload the transformer by
installing (or relamping) higher wattage lamps than planned. Note: Total wattage of all lamps connected to one
transformer must not exceed the capacity of that transformer. Do not install luminaire within 10 feet (3.04m) of
a pool, spa or fountain.
SAFETY WARNING: When relamping, be sure electrical supply is OFF. Low voltage fixtures can
become very HOT depending on the lamp wattage used. Glass lenses and metal areas above & around
the lamp can become HOT enough to blister hands. Lamp gets HOT quickly! Contact only switch/plug when
turning on. Use discretion when touching fixture and be sure to allow fixture to cool before relamping. When
relamping fixture avoid touching the lamp envelope with bare hands. If touching the lamp is necessary during
installation, clean the envelope with alcohol and dry with a clean, soft cloth before turning ON. Contamination
of the envelope may reduce lamp performance. Particular care should be taken not to locate fixtures where
small children can reach them if higher wattages are used.
NOT INTENDED FOR INDOOR USE.
MAINTENANCE: To maintain light efficiency and prevent fixture-overheating, glass lenses and enclosure must
be kept clean and free of dirt, dust, leaves, trash (combustible materials) and mineral deposits from water.
DO NOT operate luminaire with missing or damaged lens.
NOTE: Keep the lamp free from impact while burning, as this may deform the filament and shorten the lamp life.
All electrical work should be done by a qualified electrician. KEEP THIS SHEET FOR FUTURE REFERENCE.
!
!
KLV710
KLV715
!
Unit intended for mounting with Diffuser/Glass Barrier and Lamp Holder greater than 2 in. (5.08 cm)
from the ground plane.

Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
Scarab™Accent Light - KLV710 / 715 Installation Instructions
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and
accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim Products,
are warranted to be free from defects of material and/or workmanship for a
period of 1 year from date of sale, with the following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the component
manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be warranted
against defects of material and/or workmanship, and failure due to
corrosion, for a period of 25 years from date of sale.
Composite In-Grade Landscape Components
Composite In-Grade Landscape fixture components installed below grade,
shall be warranted against defects of material and/or workmanship, and
failure due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil,
shall be warranted against defects of material and/or workmanship for a
period of 3 years from date of sale. Aluminum fixture components in direct
contact with soil shall be warranted from defects of material and failure
from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance with
applicable Kim instructions, specifications and accepted trade practices,
are covered by the Kim Warranty. During the warranty period, with proof of
purchase, Kim will repair or replace with the same or similar product, at
Kim's option, without charge. Labor costs are the owner's responsibility
and are excluded from this warranty. This warranty is void if the product is
modified, tampered with, misapplied, poorly installed, improperly
maintained, or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the exclusive
remedy of the purchaser. This warranty is in lieu of all other warranties,
expressed or implied, including any implied warranty of fitness for a
particular application. Kim Lighting shall not be liable to the purchaser for
indirect or consequential damages.
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
IMPORTANT: Do not overload the transformer
by installing (or relamping) higher wattage
lamps than planned. The total wattage of all
lamps connected to one transformer must not
exceed the capacity of that transformer.
4. Install shield and lens with
short side down to drain water
and tighten screws
progressively.
5. Loosen screw, adjust fixture
angle, and tighten screw.
6. Loosen setscrew, adjust
fixture rotation, and tighten
setscrew.
LAMP INFORMATION
Cat. No. Lamp Type Max. Watts
KLV710 / KLV715 MR16 Bi pin 50
Additional wire and connectors may
be purchased from Kim Lighting:
KLV427 #12-2 Cable
KLV432 #8-2 Cable
KLV410 Connector
KLV411 Connector