HUBER+SUHNER MASTERLINE Ultimate Small Cell User manual

INSTALLATION
MANUAL
HUBER+SUHNER AG
Fiber Optics
MASTERLINE Ultimate Small Cell
DOC-0000803869
November 24, 2017
Page 1 of 4
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of
tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel
voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these p
roducts. For advice concerning the gen-
eral handling of these products please contact HUBER+SUHNER.
MASTERLINE Ultimate Small Cell
Table of contents
•GENERAL INFORMATION..........................................................................................1
•NOTES IN THIS MANUAL ...........................................................................................1
•NOTES ON THE FULFILMENT OF LEGAL CRITERIA ..............................................1
•INSTALLATION............................................................................................................2
GENERAL INFORMATION
Read the cable system user manual and installation manual carefully. General safety instructions apply unless this docu-
ment stipulates more specific instructions. HUBER+SUHNER declines all liability and claims if the specifications are not
met.
NOTES IN THIS MANUAL
The following symbols are used in this manual.
Info notes:
Info notes contain important instructions for installation and proper use of the product throughout its life
cycle. The info notes also indicate that non-compliance may result in material damage or financial loss.
Notes about hazards and safety precautions:
Notes which indicate that non-compliance may result in danger to life and limb, as well as to material
damage. It is imperative that these notes are heeded.
NOTES ON THE FULFILMENT OF LEGAL CRITERIA
The installation of optical communications systems requires that requisite permits be obtained from all the competent au-
thorities. The installation technician is responsible for compliance with all applicable regulatory restrictions, usage regula-
tions and other guidelines. This applies to permanent and temporary installations.
•Ascertain the applicable restrictions and usage regulations prior to installation.
•Draw up a cable-laying plan prior to installation.
•Check the finished system for compliance with usage and safety regulations.

INSTALLATION MANUAL
MASTERLINE Ultimate Small Cell
Page 2 of 4
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the
use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel
voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice con
cerning the gen-
eral handling of these products please contact HUBER+SUHNER.
INSTALLATION
Step 1: Slinging points:
The Masterline Ultimate Small Cell may only
be lifted up at the slinging points marked in
red.
Avoid buckling the cable or bending it at less
than the minimum radius while the device is
being raised.
All plug-type cables must be unplugged prior
to raising.
Step 2: Fixing:
Mast mounting:
The Small Cell may only be fixed to a flat base
by the fixing lugs marked. The fixing tech-
nique must be adapted to suit the base.
Please heed the instructions given by the
manufacturer of the fixing materials.
Mast mounting:
Always use two hose clamps to fix the Small
Cell to a mast. Guide the hose clamps at the
bottom into the lugs provided and then secure
them to the mast.

INSTALLATION MANUAL
MASTERLINE Ultimate Small Cell
Page 3 of 4
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the
use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel
voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice con
cerning the gen-
eral handling of these products please contact HUBER+SUHNER.
Step 3: The feeder cable (only applies with types MLU
SC A1 and MLU SC H1) must be secured
within 1 meter by means of a suitable cable
clamp.
The offset between the first cable clamp and
the cable entry must be kept to a minimum.
The cable must be fastened at regular inter-
vals of not more than 1 meter using a suitable
cable clamp.
Step 4: In the case of a daisy chain installation, all the
Small Cell housings must be fastened in ac-
cordance with steps 1 and 2.
Step 5: Once all the Small Cell housings have been
fastened in accordance with the regulations,
they can be connected together with jumper
cables.
Remove the protective cap before plugging in
and turn the connector to the correct position
without applying pressure. Then engage the
connector by pressing. Turn it gently in the op-
posite direction to check that the connector is
properly engaged.

INSTALLATION MANUAL
MASTERLINE Ultimate Small Cell
Page 4 of 4
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the
use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel
voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice con
cerning the gen-
eral handling of these products please contact HUBER+SUHNER.
Step 6: Connect the Small Cell housing to the RRH
using jumper cables.
The connectors can be engaged in the ports
provided by applying gentle pressure. Turn it
gently in the opposite direction to check that
the connector is properly engaged.
Please refer to the general instructions in the
user manual for guidance on handling cables
and laying multi-connector cables.
Step 7: All jumper cables must be fastened at regular
intervals of not more than 1 meter using cable
clamps.
Step 8: Once all the jumper cables have been con-
nected, the main line can be connected to the
base station or to the fiber-optic cable.
The protective tube must be removed before
connecting.
When untwisting the protective tube, ensure
that the cable is not twisted around its own
axis.
Step 9: Connect the Small Cell housing to the base
station using suitable cables.
The connectors can be engaged in the ports
provided by applying gentle pressure. Turn it
gently in the opposite direction to check that
the connector is properly engaged.
Please refer to the general instructions in the
user manual for guidance on handling cables
and laying multi-connector cables.