HULALA HOME SCSD0757 User manual

ITEM NO.SC
SD0757
NOTE:
This brochure contains IMPORTANT safty info. Please read
and keep for future reference.
HULALA
H O M E
01/26

MAINTAINANCE
AND WARNING
Keep furniture away from heat sources.
Do not clean furniture with harsh cleaner
or polishes. Do not use detergents,
Solvents, abrasives, spray packs or
leather cleaner. Usenon-color mild soap
with warm water to clean spills(Mix 1:10
soap to water)
Do not place furniture under direct
sunlight, material will possibly fade over
time.
Do not use on site dry Cleaning machine.
Children should not climb or jump on the
furniture.
Do not write on furniture that is not
protectedby a padded barrier .
Not for commercial use, only for
residential use 。
Weight Limitation
80LBS
02/26

OVERVIEW
A
B
C
E
F
G
H
H
K
D
J
L
L
M
I
I
K
K
03/26

Persons Required For Assembly
：
HARDWARE
LIST
A
2Personen
1 PC
BC
D
1 PC 1 PC 1 PC
E
1 PC
F
1 PC 2 PCS
H
2 PCS
K
1 PC 3 PCS 2 PCS
G
I
L
1 PC
M
1 PC
J
04/26

x58
①x8
Be sure to inspect all packing material
carefully for small parts, that may have
come loose inside the carton during
shipment.
PARTS
LIST 1
SPARE
x5
①
②③x16 x8 x4
⑥x8
⑤
②⑥
⑤
⑦x6
⑦
④
⑧x2
⑧
x1 x1
x1
x1x1
x7
⑨
x1
⑨
05/26

x3
x4
⑩
PARTS
LIST 2
Be sure to inspect all packing material
carefully for small parts, that may have
come loose inside the carton during
shipment.
⑪⑫⑬x4
⑯x1
x12
⑭
x2
⑮x8
⑰x4
⑱x2
⑲
x18
x1
⑳
06/26

ASSEMBLY
INSTRUCTIONS
STEP1:
Prepare for part A. Align the holes in part A, insert wooden
dowel ③ by hand, tighten with screwdriver
⑳ tighten
② 。
x1
②x8 x8
③
③x8
②
③
A
②x8
⑳
⑳
③
③
③
②
②
②
07/26
A

STEP2:
Connect the part A with part C&D&E&F. align the hole in the
part C&D&E&F,insert the bolt
② and wooden dowel
③ in
part A into part C&D&E&F. insert cam bolt
④ into the
corresponding hole of side panel C&D&E&F,and tighten the
nuts ④ with a screwdriver
⑳. After installation, cover the
screw holes with ⑰ . Make sure the groove is in same side as
picture show.
④x8
x8 x1
④⑰x8
⑰x8
C
D
E
F
AC&D&E&F
C&D&E&F
C&D&E&F
A
A
A
⑳
⑳
08/26
④
④
④

STEP3:
slide in the part H,G,H into the groove in part C,E and E,F
and F,D . make sure they are also in groove in part A.
C
H
G
H
D
F
E
09/26
A

STEP4:
Connect the part B the pre-assembled unit in step 3. Insert
the wooden dowel
③ into the part C&D&E&F as the picture
show.
Then align the holes in part B,Insert screw
⑥ and push it
down so that it connects to parts C&D&E&F. Next,and tighten
the screw ⑥
with an Allen key ⑯.
x1x8
⑥
⑯
x8
③
⑯
⑥x8
③x8
H
H
G
C
B
⑥
E
F
D
⑥
⑥
⑥
⑥
⑥
⑥
⑥
③
③
③
③
③
③
③
③
10/26