Huntleigh AKRON 3 SECTION DRAINAGE User manual

SERVICEMANUAL
794-015
AKRON3SECTION
DRAINAGE
®
Models
8241,8242
AKRON5SECTION
DRAINAGE
®
Models
8251,8252

Page 1
General Maintenance including Gas Strut
ÜIt is recommended that the following checks and adjustments are carried out at
minimum of twice a year and more frequently if the couch is in constant use.
•The framework of the couch is of steel construction and coated with
an epoxy paint finish. This is resistant to most cleaning substances.
•The major pivot points need to be lubricated sparingly with oil. Care
should be taken to keep oil away from the upholstery.
•All nuts should be checked and tightened where necessary. Care
should be taken not to over tighten the nuts on the pivot points as this
may cause them to bind.
•Air tubes should be checked to ensure that they are not pinched.
•Disconnect the mains supply and check the following;
NOTE - all electrical checks should be carried out by a suitably
qualified person.
Electric cables and mains plug should be inspected for damage and
replaced where necessary. In addition, electrical safety checks for
earth continuity (class I equipment only) and earth leakage checks
should also be carried out.
The correct value fuse of 5 amps and ASTA approved to BS1362
MUST be used.
•The upholstered top is manufactured using fire retardant vinyl. This
tends to go brittle if oil or grease (including body oils) are left on it.
The upholstery should be cleaned with warm soapy water after use.
The use of detergents is not recommended although a suitable
sterilization fluid is acceptable. Use of a couch cover or towel will
help prolong the life of the upholstery.
•Woodscrews, used to secure the upholstery, should be checked and
tightened or replaced where necessary.
•The hinge pins on the head and foot sections should be checked to
ensure that they have not moved within the hinge tubes. If the pin
protrudes, a heavy tap with a hammer should be required to relocate
it. If the pin moves easily, the knurling may be insufficient to hold the
hinge pin in place and a new pin must be fitted.

Page 2
General Maintenance including Gas Strut (continued).
•Gas strut controls should be checked for a small amount of clearance
between the operating flap and the release pin, throughout the range
of movement. Should clearance be inadequate, or the top sinks whilst
in use, the following adjustment should be made; firmly grasp the
body of the strut and rotate in an anti clockwise direction. Check for
clearance and repeat as necessary.
Should the gas strut fail to operate, refer to the above adjustment but
rotate in a clockwise direction.
Manufacturers Details
Huntleigh Akron
1 Farthing Road
Ipswich
Suffolk
IP1 5AP
England
Tel. [phone]
Fax. [phone]
Huntleigh Akron T/A a Division of Huntleigh Nesbit Evans Limited
A Member of the Huntleigh Technology PLC Group of Companies
© Huntleigh Technology PLC 1999

Page 3
Revision History
DOCUMENT ISSUE DCN No. SIGNED DATE
All Pages 1~Paula Hammond 23.10.98
2A0152Z 2A0160Z
2A0201Z 2 897 Paula Hammond 25.2.99
2A0230Z 3 899 Paula Hammond 24.3.99
2A0152Z 2B0159Z
2A0160Z 2B0162Z 4914/916 Gary Mullenger 9.11.99
2N0103Z 5 941 Gary Mullenger 6.6.99
2A0201Z 6 960 Jason Barker 18.12.00

PARTS LIST
STANDARD BASE ASSEMBLY
2A0201Z – Issue 14
Issue 10 11 12 13 14
Date 3/97 3/98 9/98 2/99 11/00
E.C.N. 827 855 867 897 960
Reference
Number Description Quantity Part Number Issue Status
1H Section 23A0104Z 2
2Link Bar 23A0107Z 1
3Base Frame 13A0201Z 3
4Long Wheel Plunger 23A9405Z 1
5Short Wheel Plunger 23A9406Z 0
6Wheel Cam 23E0112Z 2
7Pivot Rod 23G0117Z 1
83" Castor 45H0402A 0
9M10 x 20mm Socket Head Set Screw 45J8058R 0
10 10mm Flat Starlock 85L3304Z 0
11 M10 Half Nut 15L3319A 0
12 M10 Spring Washer 45L3351K 0
13 M10 Flat Washer 45L3362K 0
14 1/4" x 1" Seloc Pin 45M0408C 0
15 1700 x 19 Spring Ring 45M4296S 0
16 11/2" x 3/4" x 16G Insert 85N1107E 0
17 11/2" x 11/2" x 12G Insert 85N1111C 0
18 40mm x 40mm Moulded End Cap 45N3737M 0
19 40mm x 40mm x 2.5mm Insert 15N3737V 0
20 40mm x 40mm x 2-4mm End Cap 75N3737Y 0
21 10mm Foot Adjusting Stud 15N3782U 0
22 100mm x 50mm x 2-4mm End Cap 25N4939Y 0
23 Bronze Flanged Bush 12 5P8000Z 0
24 Nylon Foot Lever 45T0028Z 1
25 Pedal Rubber 45T3200Z 0
26 Huntleigh Akron Label 15U1006Z 2
27 Pedal Sticker 45U1066Z 1

PARTS LIST
STANDARD FBS SYSTEM
2A0230Z – Issue 02
\\MAIN_SERVER\WORKDOCS\P-LIST\2A0230Z.DOC 25th March 1999
Reference
Number Description Quantity Part Number Issue Status
1Mechanism Holder 13A0231Z 0
2Sleeve Pivot Mount Bracket 23A0232Z 1
3LHS Push Pull Assembly 13A0233Z 0
4RHS Push Pull Assembly 13A0234Z 0
5Adjusting Stud 23F0230Z 0
6Hanning Handswitch 25F2100Z 0
7Hanning Round Air Pipe 0.7 5F7000Z 0
8Air Tube Connector 15F7200Z 0
9Mechanism Spring 25G6000Z 0
10 M6 x 6mm Grub Screw 45J7653Z 0
11 M8 x 10mm Grub Screw 25J7855Z 0
12 M8 x 25mm Hex Set Screw 25J7859N 0
13 M8 Full Nut 65L3119B 0
14 M8 Nyloc Nut 45L3119C 0
15 M8 Flat Washer 10 5L3162K 0
16 M8 Nut Cap 45N0028X 0
17 7/8" x 16G Round Insert 45N9208M 0
18 Large Curly Wrap 0.14 5S0327Z 0
19 Mechanism Guard 15T0047Z 0
20 Raise/Lower Sticker 65U1095Z 0

PARTS LIST
230V HANNING KIT
2B0159Z – Issue 12
Issue 10 11 12
Date 10/96 03/98 11/99
E.C.N. 811 855 914
Reference
Number Description Quantity Part Number Issue Status
1Front Mounting Bracket 13A0130Z 1
2Rear Mounting Bracket 13A0131Z 1
3Hanning Ram 230V (Type V) 15F0601Z 0
4Hanning Mains Lead (4 metres) 15F6000Z 0
5Hanning Plug Rubber 15F6100Z 0
6Hanning Ram Plug 15F6200Z 0
7M8 x 70mm Hex Bolt 25J7868A 0
8M10 x 65mm Hex Bolt 25J8067A 0
9M12 x 50mm Hex Bolt 25J8264A 0
10 M8 Nyloc Nut 25L3119C 0
11 M8 Flat Washer 45L3162K 0
12 M10 Nyloc Nut 25L3319C 0
13 M10 Flat Washer 25L3362K 0
14 M12 Nyloc Nut 25L3519C 0
15 3/16" x 1/2" Pop Rivet 35M0304G 0
16 M10 Nut Cap 25N0029X 0
17 M12 Nut Cap 25N0030X 0
18 M5 Screw Mounted Tyrap 35S0322Z 0
19 Serial Number Label 1760.41 1