Huntleigh AKRON GYNAECOLOGY 1 Series User manual

SERVICEMANUAL
794-025
AKRON
GYNAECOLOGY1
®
Models
9721,9722,9731,
9732,9742,9752

Page 1
General Maintenance including Gas Strut
?It is recommended that the following checks and adjustments are carried out at
minimum of twice a year and more frequently if the couch is in constant use.
?The framework of the couch is of steel construction and coated
with an epoxy paint finish. This is resistant to most cleaning
substances.
?The major pivot points need to be lubricated sparingly with oil.
Care should be taken to keep oil away from the upholstery.
?All nuts should be checked and tightened where necessary.
Care should be taken not to over tighten the nuts on the pivot
points as this may cause them to bind.
?Air tubes should be checked to ensure that they are not
pinched.
?Disconnect the mains supply and check the following;
NOTE - all electrical checks should be carried out by a suitably
qualified person.
Electric cables and mains plug should be inspected for damage
and replaced where necessary. In addition, electrical safety
checks for earth continuity (class I equipment only) and earth
leakage checks should also be carried out.
The correct value fuse of 5 amps and ASTA approved to
BS1362 MUST be used.
?The upholstered top is manufactured using fire retardant vinyl.
This tends to go brittle if oil or grease (including body oils) are
left on it. The upholstery should be cleaned with warm soapy
water after use. The use of detergents is not recommended
although a suitable sterilization fluid is acceptable. Use of a
couch cover or towel will help prolong the life of the upholstery.
?Woodscrews, used to secure the upholstery, should be checked
and tightened or replaced where necessary.
?The hinge pins on the head and foot sections should be
checked to ensure that they have not moved within the hinge
tubes. If the pin protrudes, a heavy tap with a hammer should
be required to relocate it. If the pin moves easily, the knurling
may be insufficient to hold the hinge pin in place and a new pin
must be fitted.

Page 2
General Maintenance including Gas Strut (continued).
?Gas strut controls should be checked for a small amount of
clearance between the operating flap and the release pin,
throughout the range of movement. Should clearance be
inadequate, or the top sinks whilst in use, the following
adjustment should be made; firmly grasp the body of the strut
and rotate in an anti clockwise direction. Check for clearance
and repeat as necessary.
Should the gas strut fail to operate, refer to the above
adjustment but rotate in a clockwise direction.
Manufacturers Details
Huntleigh Akron
1 Farthing Road
Ipswich
Suffolk
IP1 5AP
England
Tel. [phone]
Fax. [phone]
Huntleigh Akron T/A a Division of Huntleigh Nesbit Evans Limited
A Member of the Huntleigh Technology PLC Group of Companies
© Huntleigh Technology PLC 2000

Page 3
Gynaecology 1 Revision History
DOCUMENT ISSUE DCN No. SIGNED DATE
All Pages 1 936 Gary Mullenger 14/6/00
2M3416Z 2 945 Jason Barker 1/9/00
2M3410Z 3 947 Jason Barker 8/9/00
2M3420Z 2M3421Z 4 951 Jason Barker 23/10/00
2M3424Z 5 964 Jason Barker 15/01/01
A7309 A7310 6 970 Jason Barker 30/03/01

PARTS LIST
230V HANNING RAM KIT
2M2082Z – Issue 08
Issue 5 6 7 8
Date 3/96 10/96 4/98 9/99
E.C.N. 775 811 855 912
Reference
Number Description Quantity Part Number Issue Status
1Motor Mounting Bracket 13A2006Z 0
2Ram Fixing Pin 13A2088Z 0
3Spacer (17.5mm) 23G9435Z 0
4Hanning Ram 230V (Type H) 15F0603Z 0
5Hanning Mains Lead (4 metres) 15F6000Z 0
6Hanning Plug Rubber 15F6100Z 0
7Hanning Ram Plug 15F6200Z 0
8M8 x 55mm Hex Bolt 25J7865A 0
9M12 x 50mm Hex Bolt 15J8264A 0
10 M8 Nyloc Nut 25L3119C 0
11 M8 Flat Washer 45L3162K 0
12 12mm Star-Lock Capped 25L3503Z 0
13 M12 Nyloc Nut 15L3519C 0
14 M12 Flat Washer 25L3562K 0
15 1/8" x 3/8" Pop Rivet 15M0203G 0
16 M8 Nut Cap 25N0028X 0
17 M12 Nut Cap 15N0030X 0
18 Medium Cable Tie 15S0316Z 0
19 Cable Tie Base 15S0320Z 0
20 Large Curly Wrap 0.2 5S0327Z 0
21 Serial Number Label 1760.41 1

PARTS LIST
115V HANNING RAM KIT
2M2083Z – Issue 07
Issue 4 5 6 7
Date 3/96 10/96 4/98 9/99
E.C.N. 775 811 855 912
Reference
Number Description Quantity Part Number Issue Status
1Motor Mounting Bracket 13A2006Z 0
2Ram Fixing Pin 13A2088Z 0
3Spacer (17.5mm) 23G9435Z 0
4Hanning Ram 115V (Type H) 15F0504Z 0
5Hanning Mains Lead (4 metres) 15F6000Z 0
6Hanning Plug Rubber 15F6100Z 0
7Hanning Ram Plug 15F6200Z 0
8M8 x 55mm Hex Bolt 25J7865A 0
9M12 x 50mm Hex Bolt 15J8264A 0
10 M8 Nyloc Nut 25L3119C 0
11 M8 Flat Washer 45L3162K 0
12 12mm Star-Lock Capped 25L3503Z 0
13 M12 Nyloc Nut 15L3519C 0
14 M12 Flat Washer 25L3562K 0
15 1/8" x 3/8" Pop Rivet 15M0203G 0
16 M8 Nut Cap 25N0028X 0
17 M12 Nut Cap 15N0030X 0
18 Medium Cable Tie 15S0316Z 0
19 Cable Tie Base 15S0320Z 0
20 Large Curly Wrap 0.2 5S0327Z 0
21 Serial Number Label 1760.44 1

PARTS LIST
2M3416Z HYDRAULIC RAM KIT
2M3416Z – Issue 03
Issue 1 2 3
Date 9/99 8/00 5/01
E.C.N. 908 945 974
Reference
Number Description Quantity Part Number Issue Status
1Pump Mounting Bracket 13A0142Z 1
2Pump Ring 13A0143Z 2
3Left Hand Foot Lever 13A2012Z 5
4Right Hand Foot Lever 13A2014Z 5
5Ram Fixing Pin 13A2088Z 0
6Packing Section 13A3694Z 0
725mm Spacer 23G9436Z 0
8Hydraulic Ram 15F5100Z 0
9M6x12 CSK Set Screw 15J7656Y 0
10 M8x85 Bolt Hex Ht 25J7871A 0
11 M6 Shake-proof Washer 15L2955K 0
12 M8 Nyloc Nut 25L3119C 0
13 M8 Flat Washer 45L3162K 0
14 12mm Star-Lock Capped 25L3503Z 0
15 8x30mm Spirol Pin 25M3161E 0
16 M8 Nut Cap 25N0028X 0
17 50x25x2.5mm Grey Insert 25N3944Z 0
18 Pedal Rubber 25T3200Z 0
19 Pedal Sticker 25U1066Z 1
20 Serial Number Label 1760.40 0