Husky BED1007 KING User manual

1
ASSEMBLY INSTRUCTIONS
ITEM NO: BED1007 KING
A
5/16"×1-1/4"
F
E
H
5/16"
B
5/16"×2"
G
5/16"
5/16"
CD
5/16"×1"
2 3 4 5 6
7 8 9 10 11 12
REMINDER DO NOT OVER TIGHTEN ALL BOLTS UNTIL THE BED IS FULLY SET-UP
13
Wingback
2pcs
5/16"×5"
Headboard
1pc HB Leg
2pcs
Footboard
1pc FB Feet
2pcs
Headboard Crossband
1pc
Headboard Crossband
1pc Side Rail
4pcs
Side Rail Feet
2pcs
Support Rail
4pcs
Support Leg
4pcs
Center Support Leg
2pcs
Center Crossband
1pc Slats
12pcs
Bolt
8PCS
Bolt
20PCS
Bolt
16PCS
Bolt
2PCS
Nut
4PCS
Flat washer
5/16"*19MM
50PCS
1PC 1PC
Allen Key Box Wrench
B F
FB
G
1
2
2
FB
G
4PCS 4PCS
STEP 1:STEP 1:
At the back of headboard ( Part 1 ) install the HB leg ( Part 2 ) by using hard ware
provided .
Use allen key (Part G ) to screw in bolt (Part B ) and washer ( Part F ) on each
side ( 2 Bolts & 2 Washers on each side ) . Do not forget about the washer as
this will keep your bed sturdy !

C F
3
GCF
G
C
F
1
2
2
5
4
4
4PCS 4PCS
STEP 2 :STEP 2 : On the headboard (Part 1), install the HB crossband (Part 5) by
using hardware provided. Use the Allen Key (Part G) to screw in the bolt
(Part C) and the washer (Part F) on each side (2 Bolts & 2 Washers on
each side).
STEP 3 : Turn the footboard (Part 3) over and screw in
the footboard legs (Parts 4)

A
G
F
6
6
6
6
7
7
A F C F
4PCS 4PCS 4PCS 4PCS
G
C
F
G
C
F
1
63
STEP 4 : Now its time to connect the side rails (Part 6), you must line
up 2 (Part 6's) together as shown in the photo. Take the side rail feet
(Part 7) and line up the holes of the side rails (You will see 2 holes on
each side of the side rails to bolt on the Side rail feet (Part 7),
pairs of side rails.You will use 2 bolts (Part A) and 2 washers (Part F)
on each side rail feet.
STEP 5: First, lock in your side rail and the footboard in (Look at
photo).You will now take one side of the completed Side Rail and
bolt that onto the Headboard, make sure the inside of the side rail is
facing inside, another way to know it is facing inside is that the Side
Rail feet should be on the inside of the bed. For this step you will
STEP 4 : Now its time to connect the side rails (Part 6), you must line
up 2 (Part 6's) together as shown in the photo. Take the side rail feet
(Part 7) and line up the holes of the side rails (You will see 2 holes on
each side of the side rails to bolt on the Side rail feet (Part 7),
pairs of side rails.You will use 2 bolts (Part A) and 2 washers (Part F)
on each side rail feet.
STEP 5: First, lock in your side rail and the footboard in (Look at
photo).You will now take one side of the completed Side Rail and
bolt that onto the Headboard, make sure the inside of the side rail is
facing inside, another way to know it is facing inside is that the Side
Rail feet should be on the inside of the bed. For this step you will
need 4 Part C and 4 Part F.

8
8
9
10
9
D F
4PCS 4PCS B F 8PCS 8PCS
G
B
F
G
B
F
G
B
F
10
9
9
8
8
G
C
F
G
C
F
1
63
6
STEP 6: You will be doing the same thing for Step 6 that you
step 5 (Only difference is your now connecting the right side rail),
please refer to step 5 if you are lost.
STEP 7: This step requires to properly bolt on the Center Support Rail (Part 8).
On each side of the center support rail, you will install 2 support legs (Part 9)
which will require Part B, F, & G. Simply put the support leg below the center support
rail and use 1 bolts on each legs on top (Washer first then Bolt), and use an Allen key
to tighten it up.
Now let's install center support leg ( Part 10 ) shown in the photo which is also a
support leg that has a holder on top to hold the weight of the center support rail, use
2 bolts & 2 washers on the leg on top, than use an Allen key to tighten it up.
Repeat for an other one, as king bed with 2 center support rails

BF E C F
5
6
6
G
BFH
E
F
G
C
F
8
8
8
8
6
6
8
8
8
8
4PCS 4PCS 8PCS 4PCS 4PCS
STEP 8: Take the center support rail from Step 7 and lay it in the middle of the
bed from headboard to footboard. You will need 4 Part B 8 Part F and 4 Part
E. Follow the diagram and bolt everything on from the center support rail to the
HB cross brand (Bellow the headboard)
STEP 9: Similar to Step 8, you will use the 4 bolts (Part C) and 4 washers
(Part F) and screw in the bolts to the footboard from the center support rail.

G
A
F
11
11
6
7
7
6
A F B E
2 PCS
G
B
E
10
G
B
E
10
2 PCS
4PCS 4PCS
STEP 10: Take Part 11 (Center Crossband) and install that in the middle (As shown
in the photo) by simply using Part A (Bolts) and Part F (Washers) and bolt them into
the top holes in the side rails. This is to make the base of the bed much stronger!
STEP 11: This one is easy ! Simply take one bolt (Part B) and one washer (Part F)
and bolt that into center where the center support rail and cross band lay on top of
each other as shown in photo.

G
B
F
G
D
F
13
13
R
L
13
13
B F
4 PCS 4 PCS D F
2 PCS 2 PCS
STEP 12: Take Part 13 ( Wingback ) and install that on the both side of
headboard ( As shown in the photo ) by using Part B ( Bolts ) and Part F
( Washers ) and bolt them into the holes, make sure the holes are lined up
before installation,and please do not over tighten all the bolts until we finished
step 13
STEP 13：Simply take 2 bolts ( Part D ) and 2 washer ( Part F ) and bolt that in
to the bottom holes on HB leg and wingback than you guy can tighten up all the
bolts used on step12 and step 13

12
12
12
STEP 14:
STEP 15: You're almost therel Simply lay the Slats on the sides of
the side ralls (On the Inside) you can roll them out and the velcro
stick right on (Part 12)
STEP 14:
Put the back fabric down to bottom,than smooth it by velcro
stick right .

STEP 16: Congratulations, you
forget to leave us a positive review when you wake up =)
made it to the end! Time to sleep like a baby and