Huviron SK-D300IR/HT21AI User manual

FULL HD-TVI(1080P)
IR D&N DOME CAMERA
SK-D300IR(D)/HT21AI
MANUAL
1. Opening the dome :
Pushing the latch button.
(Remove the protection
sheet after installing.)
◐ HOW TO INSTALL
2. Removing the dome :
Lift the dome. When you
push the latch button, it is
unlocked and you can lift
the dome.
1. 1/2.9" Sony CMOS sensor
2. Full HD(1920x1080) Resolution
3. DAY & NIGHT Function
4. WDR (Wide Dynamic Range) Function
5. 3D DNR Function
6. Privacy mask function 16 area
7. On Screen Display menu
8. Intelligent motion detection
9. Output : HD-TVI/CVBS
10. Protocol Pelco-C
11. This camera is incredibly flexible to install with its 3-axis camera
construction, which makes the camera ceiling, wall or slope
mountable
12. 20M range visible in total darkness with 24pcs of IR LEDs.(Indoor)
13. Up to 500M Full HD-TVI Tranmission via Coaxial cable.(Maximum
tranmission distance may vary with type of coaxial cable)
◐ FEATURES
◐ DIMENSION
◐ ASSEMBLY
1. Do not install the camera outdoors.
2. Choose an ideal location for the camera, since a camera unit must
be protected against vibration.
3. Be careful not to scratch the camera unit, especially lens or dome
cover.
4. Use the camera within the temperature(-45℃~50℃).
5. Avoid any direct sun light toward the lens.
6. Use the AC adaptor 12V DC, 600mA regulated. Dual voltage
product can use 24V AC, 600mA adaptor.(option)
◐ PRECAUTION
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
3. Camera installation :
(1) Fix the camera set with the supplied
screws on ceiling or wall mount. If you
don't use supplied screws, the camera
may fall off.
(2) Please refer to '4. Camera angle
adjustment' regarding adjust camera
angle.
(3) Lens adjustment(Vari-focal Lens only)
After opening the LED cover,
① By turning the "Tele-Wide" knob, you can access a range of
focal lengths within specified limits.
② Since then, by turning the "Near-Far" knob, you can set the
focus toward the wanted object.
(4) Re-assemble the camera.
1
2w
NFT
4. Camera angle adjustment :
(1) Pan adjustment : Grasp the disk of camera and then adjust
direction to the right or left(-180°~180°)
(2) Tilt adjustment : Grasp the LED cover of camera and then adjust
direction to the up or down(6°~ 90°)
(3) Roll adjustment : Grasp the camera holder and then rotate
(-178°~178°)
<Caution> If you try to adjust the camera out of limited angle, it might
cause troubles and damage to camera.
Protection sheet
LATCH BUTTON
SCREW TP1
3.5x20 2EA
SCREW TP1
3.5x20 2EA
<Ceiling mount>
<Wall mount>
ROTATION
U
D
R
L
LED COVER
DISK
CAMERA
HOLDER
Ø100
Ø130.8 Ø109
48.1
101
SK-D300(IR)
DOME COVER ASS’Y
SK-D300(IR)
CAMERA MODULE ASS’Y
SCREW
HARNESS
LED COVER
ASS’Y
SCREW
CONTROL PCB ASS’Y
PUSH BUTTON
DISK
BASE CABLE
Take off the
marked part
by using nipper
for lpacing
cable out.
Hole
Fix the disk
(Pan angle)
using by a
screw driver
on M3X10
screws
in the holes
M3x10 SCREW
Take off the
marked part
by using nipper
for lpacing
cable out.
Hole
Fix the disk
(Pan angle)
using by a
screw driver
on M3X10
screws
in the holes
M3x10 SCREW

STRUCTURE SPECIFICATION
MECHANICAL
Dimension Ø130.8Ⅹ101(H) mm
Weight Approx. 500g
ENVIRONMENTAL
Ingress Protection N/A
Operating Temp -45°C ~ 50°C
Humidity 0% to 90%
FUNCTION
Protocol PELCO-C
ELECTRONICAL
Supplied Voltage DC12V±10%orAC24V±10% DualVoltage
Current Consumption Max.450mA(at12V DC) : LED ON
LED IR LED 24PCS
Heater Option
Fan Option
CERTIFICATION
CE, FCC, ROHS Yes
1. How to use the jog lever
※All specification is subject to change without notice to improve the quality. 3B26621A
◐ CAMERA / STRUCTURE SPECIFICATION
◐ FUNCTION SETTING
①SET : Used to access the menu and confirm selection.
②UP, ③DOWN : Used to move the cursor to up or down.
④ LEFT, ⑤RIGHT : Used to move the cursor to left or right and change the
value.
⑥EXT-VIDEO : Extra video output terminal for installation.
Plug your test monitor in hear. The cable is option.
2. OSD menu structure
3. How to control through Pelco-C communication
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right is same as Up, Down, Left and right of
Pelco-C control
3) Enter same as menu key or IRIS open key control
6
1
2
4
3
5
SK-D300IR(D)/HT21AI
VIDEO
Image Sensor 1/2.9" SONY CMOS
Total Pixels 2010(H) 1108(V) = 2,227,080 (pixel)
Active Pixels 1944(H) 1092(V) = 2,122,848 (pixel)
Scanning System Progressive Scan
Resolution
Digital : 1920X1080p (1080p, 30/25fps)
1280X720p (720p, 60/50fps)
Analog : 700TVL
S/N More than 50dB (AGC OFF)
Video Output HD-TVI
Analog : NTSC, PAL(without WDR)
Min.Illumination Color: 1.0Lux, BW: 0.5Lux
Color DSS: 0.002Lux, BW DSS : 0.001Lux
LENS TYPE
Lens Type DC Auto Iris
Focal Length f = 2.8(W) ~ 12.0(T)mm
OPERATIONAL
On screen display Yes
Day & Night TDN (Auto / Day / Night)
Brightness 0 ~ 20 steps
Shutter Speed Auto / Manual (1/30(1/25) ~ 1/60000)
Sens-up OFF / ×2~×8
AGC 0~20 steps
Backlight WDR / BLC / OFF
HLC ON / OFF
D-WDR ON / OFF
White Balance Auto / Autoext / Manual
Sharpness 0~10 steps
Digital Noise Reduction (3D) High/Middle/Low/Off
Digital Zoom ON/OFF(X1~X8)
Motion Detection ON / OFF
Privacy Masking ON / OFF (16 Zone Selectable)
Mirror H / V / H&V / OFF
Defog ON / OFF
Function
setting menu Sub menu Summary
1.
EXPOSURE
BRIGHTNESS Adjust brightness level 0(dark) ~ 20(bright)
LENS-DC Select when use of DC Auto-Iris lense/except
the special cases, DC is standard Model
AE MODE Select AE MODE
SHUTTER Can be set in AUTO or MANUAL
SENS-UP Select maximum DSS(Digital Slow Shutter) OFF, x2~X8
AGC Select Auto Gain Control
2.
WHITE BAL
AWB Select WHITE BALANCE mode
▷AUTO Automatically adjusts color according to the lighting
▷AUTO ext Faster extension version of Auto
MANUAL Adjust the white balance manually
3.
BACK
LIGHT
BACKLIGH Select Backlight compenstaion mode
WDR Adjust WDR level - Low / Middle / High
HLC Select High Light Compensation.
BLC
▷AREA Control BLC area according to light condition.
▷POS-X Adjust the window X- Axis position
▷POS-Y Adjust the window Y- Axis position
▷SIZ-X Adjust the window X- Axis size
▷SIZ-Y Adjust the window Y- Axis size
4.
DAY&
NIGHT
DAY&NIGHT Select Day&Night mode
AUTO-CDS
Automatic switching between day operation
(colormode) and night operation
(black and white mode)
▷IR-LED LED On/Off Control
▷ANTI-SAT Compensate when IR hunting happens.
When you use this function.
▷AGC THRS Day&Night change level. Higher level make the night
mode changed in lower illumination.
▷AGC
MARGIN Day to night and night to day switch margin
▷DELAY 2 ~ 60 second
5.
IMAGE
DNR Select Digital Noise Reduction
SHARPNESS Adjust sharpness level
COLOR GAIN Adjust Color gain value 0~20 Steps.
GAMMA Selecte gamma mode. 0.45~0.65
D-WDR Select Digital WDR(Wide Dynamic Range)
DEFOG Carry out defog function.
SHADING Select Lens shading compensation. (OFF / ON)
MIRROR
H-Flip : Flip the picture horizontally on the screen
V-Flip: Flip the picture vertically on the screen
Rotate : Flip the picture horizontally
& vertically on the screen
6.
SPECIAL
TITLE Camera title edit and display on / off select
PRIVACY Hide an area you want to hide on the screen
MOTION When there is movement of the subject on the
screen,there will be motion detection
D-ZOOM Select digital zoom magnification. Max 8x
Function
setting menu Sub menu Summary
6.
SPECIAL
LANGUAGE Select Language
COMM. Setup Camera ID and baud-rate.
(Pelco-D/P Auto detect)
7.
SYSTEM
IMAGE
RANGE Select pedestal level scale
HD Format Select HD output format. 1080p
HD FPS Select HD output frame rate.
1080p 30, 25
CVBS Select CVBS output mode. NTSC or PAL
8. RESET All the settings will be restored to the factory default
9. EXIT Escape the menu