Huviron SK-P461D/HD21 User manual

1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface.
It will cause falling or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
(Use the AC adaptor 12V DC regulated, 1.5A)
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Due to the possibility of water leakage, do not cut or peel off the
cable. In case you cut or peel off the cable, the warranty will be void.
8. Do not adhere dangerous articles to the camera.
8. Do not adhere dangerous articles to the camera.
9. Please use the camera unit within given temperature and electricitylimit.
10. Please make sure that installation should be done by qualified
service person only.
11. Do not disassemble the unit by yourself. When there is problem
with the unit please contact after-sale service center or the shop
where you bought.
11. This camera is incredibly flexible to install with its 3-axis camera
1. 1/2.9" SONY CMOS
2. Full HD Resolution
3. DAY & NIGHT Function
4. WDR (Wide Dynamic Range)
5. 3D DNR Function
6. Privacy mask function 28 area
7. On Screen Display menu
8. Intelligent motion detection 4 area
9. Output : HD-SDI/CVBS
10. Protocol RS-485 : PELCO - P, PELCO - D
CAUTION
FEATURE
construction, which makes the camera ceiling, wall or slope
mountable
12. This product is "waterproof" to resist rain, snow and other weather
factors(IP68)
13. 30M range visible in total darkness with 40pcs of IR LEDs.(Indoor)
ACCESSORIES
ANCHOR 6x30, 4EA
SCREW 4x35 TP1 PAN SUS, 4EA
WRENCH 3mm L TYPE, 1EA
SUNVISOR BOLT, 1EA
Extra video output cable for installation,
1EA(option)
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
HD-SDI CAMERA
SK-P461(D)/HD21
MANUAL
HOW TO INSTALL
Ø6 Ø25
ANCHOR 6x30, 4EA
SCREW Tp1 4x35, 4EA
BOLT
SUNVISOR
5-A. Loosen the bolt A, B, C-1 and C-2 by using the 3mm wrench
included.
6-A. Face the direction of the camera to monitor.
7-A. Tighen the bolt A, B, C-1, C-2 to complete adjustment.
5-B. Loosen the bolt by using the 3mm wrench included.
6-B. Face the direction of the camera to monitor.
7-B. Tighten the bolt to complete adjustment.
DIMENSION
101.7
101.7
206.7
205.9
80.4
80.4
Type A-
Type B-
WRENCH
BOLT A
BOLT C-2
BOLT C-1
BOLT B
Type - A
Type B-
WRENCH
BOLT
CAP
* Warnin g : This cap m ust screw tightly.
1. Make a hole of Ø25mm in diameter for passing cable.
2. Drill four holes on the wall or ceiling and insert the anchors.
3. Arrange the cables and fix the screws.

More than 50dB (AGC OFF)
HD-SDI
Analog : NTSC, PAL(without WDR)
Color: 1.0Lux, BW: 0.5Lux
Color DSS: 0.002Lux, BW DSS : 0.001Lux
DC Auto Iris
f = 2.8(W) ~ 12.0(T)mm
Yes
ICR (Auto / Day / Night)
0 ~ 20 steps
Shutter Speed
Flicker less
DSS
AGC
Backlight
HLC
ACE
Auto / Manual (1/30(1/25) ~ 1/60000)
ON / OFF
OFF / 2
ON / OFF
WDR / BLC / OFF
ON / OFF
ON / OFF
~ 8X X
White Balance
Sharpness
Digital Noise
Reduction (3D)
Digital Zoom
Auto / Autoext / Preset / Manual
0~10steps
ON/OFF( 1~ 64)X X
Freeze
Motion Detection
Privacy Masking
Mirror
ON / OFF
ON / OFF
ON / OFF (28 Zone Selectable)
H / V / H&V / OFF
VIDEO
Image Sensor
Total Pixels
Active Pixels
Scanning System
Resolution
LENS TYPE
Lens Type
Focal Length
OPERATIONAL
On screen display
Day & Night
Brightness
Auto/High/Middle/Low/Off
S/N
Video Output
Min.Illumination
86.4(W) 101.9(H) 131.3(D) mm
Approx. 900
8
g
IP 6
Ⅹ Ⅹ
Current Consumption
-45°C ~ 50°C
0% to 90%
PELCO-D , PELCO-P
2400 ~ bps
RS-485
57,600
MECHANICAL
Dimension
Weight
ENVIRONMENTAL
Ingress Protection
Operating Temp
Humidity
FUNCTION
Protocol
Baud Rate
Communication
ELECTRONICAL
Supplied Voltage
LED
Heater
Fan
CERTIFICATION
CE, FCC, ROHS
STRUCTURE SPECIFICATION
3B25764A
2. OSD menu structure
※All specification is subject to change without notice to improve the quality.
CAMERA / STRUCTURE SPECIFICATION
SK-P461D/HD21
Yes
DC12V±10%orAC24V±10% DualVoltage
Max.1A(at12V DC, 24VAC) : LED ON
IR LED40 PCS
Yes
Option
① ENTER :
②UP, ③DOWN :
④LEFT, ⑤RIGHT :
⑥FOCUS, ⑦ZOOM :
⑧EXT. VIDEO :
Used to access the menu and confirm
selection. Used to move the cursor to up or down.
Used to move the cursor to left or right
andchange the value.
Use a '+' type driver for adjusting
zoom and focus.(In case of operation Focus/Zoom,
don't put stress excessively.)
Extra video output terminal for installation.
The cable is option.
FUNCTION SETTING
1. How to use the jog lever
Z
EXT.VIDEO
F
7
6
8
2
5
13
4
*OSD menu & Focus/Zoom adjustment direction
1. Unfasten the screw of the bottom door
2. Adjust the jog lever & Focus/Zoom trimmers
3. Tighten the screw of the bottom door
A : ORANGE(RX +)
B : WHITE(RX -)
Function
RX +
RX -
Remark
RS-485A
RS-485B
o.
A
B
N
3. How to control through RS-485 communication(option)
4. Cable array(option)
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left and
right of RS-485 controller
3) Enter of Jog lever is the same as menu key or IRIS open key of RS-
485 controller
Function
setting menu Summary
Sub menu
Adjust brightness level 0(dark) ~ 20(bright)
Select maximum DSS(Digital Slow Shutter) OFF, x2~X8
Select Auto Gain Control
1.
EXPOSURE
BRIGHTNESS
AE MODE
SHUTTER
DSS
AGC
FREQ
2.
WHITE BAL
3.
BACK
LIGHT
4.
DAY&
NIGHT
AWB
AUTO
▷AUTO
▷ ext
7.
SPECIAL
8.
SYSTEM
Function
setting menu SummarySub menu
5.
IMAGE
Select WHITE BALANCE mode
LENS-DC
Automatically adjusts color according to the lighting
It is a fixed white balance mode that may be
automatically Read justed only by pressing PRESET
You can change WB as changing "RED GAIN"
and 'BLUE GAIN" in Manual mode.
CHROMA Adjust CHROMA gain value 0 ~ 20 steps
BACKLIGH Select Backlight compenstaion mode
WDR Adjust WDR level - 0 ~ 4
BLC
▷AREA Control BLC area according to light condition.
▷POS-X Adjust the window X- Axis position
▷POS-Y Adjust the window Y- Axis position
▷SIZ-X Adjust the window X- Axis size
▷SIZ-Y Adjust the window Y- Axis size
DAY&NIGHT Select Day&Night mode
AUTO
Automatic switching between day operation
(colormode) and night operation
(black and white mode)
▷IR-LED LED On/Off Control
▷ANTI-SAT Compensate when IR hunting happens.
When you use this function.
▷AGC THRS Day&Night change level. Higher level make the
night mode changed in lower illumination.
▷AGC MARGIN
▷DELAY 0 ~ 255 second
DNR
MIRROR
Select Digital Noise Reduction
H-Flip : Flip the picture horizontally on the screen
V-Flip: Flip the picture vertically on the screen
Rotate : Flip the picture horizontally
& vertically on the screen
SHARPNESS
SHADING
HLMASK
ACE
GAMMA
Adjust sharpness level
Select Lens shading compensation. (OFF / ON)
Select High Light Compensation.
Select Digital WDR(Wide Dynamic Range)
Selecte gamma mode. 0.45~0.65
TITLE
PRIVACY
Camera title edit and display on / off select
Hide an area you want to hide on the screen
MOTION When there is movement of the subject on the
screen,there will be motion detection
D-ZOOM Select digital zoom magnification. Max 64x
LANGUAGE Select Language
COMM. Setup Camera ID and baud-rate.
(Pelco-D/P Auto detect)
P.SCALE Select pedestal level scale
HD Format Select HD output format. 1080p or 720p
HD FPS
Select HD output frame rate.
1080p 30, 25
720p 60, 50
CVBS Select CVBS output mode. NTSC or PAL
RESET All the settings will be restored to the factory default
Escape the menuE X IT
▷PRESET
▷INDOOR
Can be set in AUTO or MANUAL
Select AE MODE
Select when use of DC Auto-Iris lense/except
the special cases, DC is standard Model
Select frequency
Faster extension version of Auto
Day to night and night to day switch margin
1/2.9" SONY CMOS
X
X
X , /25
X , /50
2010(H) 1108(V) = 2,227,080 (pixel)
1944(H) 1092(V) = 2,122,848 (pixel)
Progressive Scan
Digital : 1920 1080p (1080p 30 fps)
1280 720p (720p 60 fps)
Analog : 700TVL