HW Group Poseidon 3265 How to use

Poseidon 3265 – starting guide HW group
Oficjalny dystrybutor:
www.atel.com.pl 45-231 Opole tel. [phone]
ATEL ELECTRONICS
e-mail: [email protected] ul. Oleska 121 fax. [phone]
Starting Guide - Poseidon 3265
First steps for remote monitoring with Poseidon & GSM
1) Connecting Poseidon 3265


• Green POWER LED on RJ45 connector lights up – power supply is OK
• Yellow LED on the RJ45 connector blinks – connection to 10 Mbit network is OK
Accessories
600 165 Poseidon 3265 Poseidon model 3265 unit with 5 sensors and GSM modem support
600 313 Poseidon 3265 GSM2 Tset Start set - GSM modem, temperature sensors, power supply etc.
600 005 Temp-1Wire 3m Temperature probe, 3m connecting cable (1m=600 242,10m=600 056)
600 311 Temp-1Wire-Outdoor 3m Temperature probe for external use in food industry, cable 3m long
600 279 Humid-1Wire 3m Humidity probe, extending cable 3m long(1m= 600 278)
600 040 Poseidon T-Box Termination-Box for connecting up to 5 sensors, 10 cm long cable
600 280 Poseidon T-Box2 Termination-Box for connecting 2 sensors, 3m long cable
Poseidon 3265
1.
4
)
Connect temperature or humidity sensor to
IT bus
(Temp-1Wire or Humid-1Wire - RJ12 connector), the
connector must click.
1.3)
Connect power adapter to power supply (230 /
110V) and to power jack of Poseidon. The connector
must be plugged in fully, green LED lights up.
1.1)
Check DIP switches settings. For installation keep them as
shown on the picture on the right (DIP1=Off, DIP2=Off).
1.2)
RS-232 serial port for connecting GSM modem and setup
purposes.
1.5) Connect
Poseidon to Ethernet (use direct
cable to Switch, cross-over cable to PC)
GSM Modemcom G10
600
312
Poseidon T
-
Box
600 040
HTemp
-
Rack19
600
330
Temp
-
1Wire
1
m
600 242
Humid
-
1Wire 3m
600 279

Poseidon 3265 – starting guide
Oficjalny dystrybutor:
ATEL ELECTRONICS
2) Configuring the IP address
UDP Config program –
in the root folder of the supplied CD (Windows and Linux version).
The program can be
downloaded from
www.HW-group.com
Software -> UDP Config.
.
• Click the icon to run
UDP Config – the
program
automatically
searches for
connected devices
• Click the Find
Devices button to
start searching for
devices.
The program looks for devices on your local
network. To identify a particular Poseidon unit, look
at its MAC address (printed on
the label at the
bottom of the unit).
Double click a MAC address to open a dialog
window with basic device settings.
Set up network parameters
• IP address
• HTTP Port (default is 80)
• Mask
• Gateway IP address
• Name of your device –
optional
Click the Apply Changes button
to save the
settings.
Note:
Contact your network administrator if you
are unsure about these settings.
•
Reset to factory defaults
Toggle DIP1 several times within 5 seconds after powering up. Default settings
contains none passwords.
DIP1
•Disable
any configuration changes
While DIP2=On
any configuration change disabled.
Note: Set Dip2=Off to be able change IP address configuration
DIP2
Oficjalny dystrybutor:
www.atel.com.pl 45-231 Opole
e-mail: [e-mail] ul. Oleska 121
2) Configuring the IP address
– UDP Config
in the root folder of the supplied CD (Windows and Linux version).
The program looks for devices on your local
network. To identify a particular Poseidon unit, look
the label at the
Double click a MAC address to open a dialog
optional
to save the
Contact your network administrator if you
Reset to factory defaults
Toggle DIP1 several times within 5 seconds after powering up. Default settings
contains none passwords.
any configuration changes
(online demo mode)
any configuration change disabled.
Note: Set Dip2=Off to be able change IP address configuration
HW group
tel. [phone]
fax. [phone]
in the root folder of the supplied CD (Windows and Linux version).
Toggle DIP1 several times within 5 seconds after powering up. Default settings
(online demo mode)
Note: Set Dip2=Off to be able change IP address configuration

Poseidon 3265 – starting guide HW group
Oficjalny dystrybutor:
www.atel.com.pl 45-231 Opole tel. [phone]
ATEL ELECTRONICS
e-mail: [email protected] ul. Oleska 121 fax. [phone]
3) Poseidon setting – Internet browser
3.1) type device IP address into your web browser address bar or run UCP Config and click on
device IP address in the list of found devices
3.2) Poseidon 3265 webpage
•
Current Value – current value of the connected sensor. „-999.9“ means that the sensor is not available
or was initialized after device started.
• Safe Range – Sensor value range that is not in Alarm.
• Alarm Alert – Monitoring of the defined “Safe Range” exceeded or switch Dry contact input on/off
initiate Alarm state.
• „For more information“– A contact to service organization, this can be changed from „Telnet setup“.
Reading current values
• XML – values.xml file, format described using XSD – for download on the main page, detailed
comments on XML structure are available in the manual.
• SNMP – description file poseidon.mib can be downloaded on the main page. Standard SNMP
ports 161 and 162 can be configured in Flash setup.
• Modbus/TCP– structure description is available in the manual and in application examples.
Standard port 502 is opened for reading.
Device IP address
Contact unique ID
Monitored range of
each probe
Notification about
value out of range
Device name
„
Flash setup
“
detailed configuration
Display of
SNMP MIB
and values.XML
You can change this
text, check manual..

Poseidon 3265 – starting guide HW group
Oficjalny dystrybutor:
www.atel.com.pl 45-231 Opole tel. [phone]
ATEL ELECTRONICS
e-mail: [email protected] ul. Oleska 121 fax. [phone]
4) Flash Setup – probe detection
Click on “Flash Setup” from web page to open this graphics page.
Flash Setup requires Macromedia Flash player installed in web browser. If you do not have it, you
can download the latest version from Internet or find it on CD: \Poseidon\ install_flash_player_7.msi
Sensor detection: Tab „Sensors Setup“, click on “Autodetect Sensors”.
Using Flash setup you can:
• Setup names of sensors, „Safe Range“ for alarm and to where the
Alarm alert will be sent.
• Detect and configure GSM modem.
• Monitor current values, refresh in seconds.
• Select temperature units (°C, °F, °K)
• Setup actual time and select NTP server to synchronize the time.
• Setup SNMP parameters (Community names & rights) and define
where to send SNMP Traps.
• Setup Alarm alert via email, and test it.
• Setup security elements: Names and password, ranges of IP
addresses.
More information can be found in the manual or at www.HW-group.com

Poseidon 3265 – starting guide HW group
Oficjalny dystrybutor:
www.atel.com.pl 45-231 Opole tel. [phone]
ATEL ELECTRONICS
e-mail: [email protected] ul. Oleska 121 fax. [phone]
5) Connecting GSM modem
Following description is related to FW version 3.0.5 and higher. Latest FW can be downloaded from
the Poseidon XXXX page.
1. Deactivate PIN code protection of the SIM card.
If the function is active, the phone requires PIN code after start up.
2. Setup IP address and connect sensors to Poseidon 3265 according to previous procedure.
3. Connect GSM modem and Poseidon 3265 with supplied RS-232 cable.
4. Insert SIM card to modem slot.
5. Connect power supply to the GSM modem
6. Connect power supply to the Poseidon, wait for about 50 seconds for GSM modem activation.
7. Web browser opens FLASH Setup, tab "Email & SMS Setup" and verify if "Enabled" is
checked on "GSM SMS Interface" field.
o"RS-232 GSM module" should show "FOUND".
o"SMS centre" should show values from SIM card. If not, fill in your operator number.
8. Fill in "Alarm SMS Recipient 1" with target phone number where alarm is sent to and push
"SendTestSMS" button.
Enable GSM modem
Send Test SMS when GSM
modem Ready
SMS Center number
detected automatically
from the SIM card, when
GSM modem
Ready