Hy-Brid Lifts Push-Around Series Use and care manual

BY CUSTOM EQUIPMENT LLC
OPERATION
& SAFETY
MANUAL
MOBILE
ELEVATING
WORK
PLATFORMS
ANSI A92.20
CSA-B354.6:17
PUSH-
AROUND
SERIES
PA-1030
PA1.1S | REV A
SERIAL NO.

This manual refers to serial number(s):
PA-1030 PA10-50001 -
For older Serial Numbers refer to our website:
www.hybridlifts.com/Manuals.htm
General Information
2647 Hwy 175
Richfield, WI 53076
U.S.A.
[phone]
[phone]
www.hybridlifts.com
Service Information
[phone]
[email protected]
Parts Information
[phone]
[email protected]
Register your Hy-Brid Lift at:
www.hybridlifts.com/RegisterOnline.htm
Register your Hy-Brid Lift to:
• Receive product updates and recalls
• Receive service bulletins, product and part
recalls, and other important notifications
• Comply with ANSI A92.20 Standards
• Provide better records for service
REGISTERING YOUR MEWP WITH THE
MANUFACTURER IS AN ANSI A92.20
REQUIREMENT.
PUSH-AROUND SERIES PA-1030
2

FOREWORD
THE OPERATION AND SAFETY MANUAL MUST BE
READ AND UNDERSTOOD PRIOR TO OPERATING THE
MACHINE.
ANY MODIFICATION ON THIS MACHINE WITHOUT
THE EXPRESS WRITTEN CONSENT OF THE
MANUFACTURER IS PROHIBITED.
USE OF FALL ARREST SYSTEMS ATTACHED TO
ANCHORAGE POINTS ON EQUIPMENT MAY CAUSE
MACHINE TO TIP, RESULTING IN SERIOUS INJURY OR
DEATH.
Original instructions are written in English
The purpose of this Operations and Safety manual is to provide users with the instructions and operating
procedures essential to properly and safely operate the Hy-Brid Lift for its intended purpose, and to position
personnel and their necessary tools and materials.
• The user/operator should not accept operating responsibility until the manual has been read and
understood as well as having operated the lift under supervision of an experienced and qualified operator.
• Because the manufacturer has no direct control over machine application and operation, proper safety
practices are the responsibility of the user and all operating personnel.
The guardrail system around the perimeter of
the platform is the fall protection system for
manual-propelled Mobile Elevating Work Platforms
(MEWP) per the A92.20/CSA-B354.6:17 Standards.
It is prohibited to use an MEWP manufactured
by Custom Equipment, LLC, with any portion—
or all—of the guardrails removed. Lanyard
anchorage points on this type of equipment
are not required to conform to the applicable
standard. However, if anchorage points for lanyard
attachments are required by site authorities or
other regulations, the anchorage points on all
equipment manufactured by Custom Equipment,
LLC are designed to be used for work positioning
restraints of personnel only. Lanyard lengths are
to be determined by operator/owner to restrict
the operator to the confines within the guardrail
system. FIGURE 1: Lanyard Attachment
FALL PROTECTION NOTICE
3
OPERATION & SAFETY MANUAL PA1.1-S REV A

TABLE OF CONTENTS
FOREWORD .................................................................................................................................................................................3
TABLE OF CONTENTS............................................................................................................................................................... 4
INDEX OF FIGURES.....................................................................................................................................................................5
SECTION 1 FAMILIARIZATION ................................................................................................................................................6
1.1 | REQUIREMENT FOR CONFIRMATION OF MANUALS......................................................................................................... 6
1.2 | PURPOSE AND FUNCTION OF CONTROLS......................................................................................................................... 6
1.3 | NONOPERATING CHARACTERISTICS .................................................................................................................................. 6
1.4 | OPERATING CHARACTERISTICS .............................................................................................................................................. 7
SECTION 2 SAFETY.....................................................................................................................................................................8
2.1 | SAFETY SYMBOLS .........................................................................................................................................................................8
2.2 | GENERAL RULES AND PRECAUTIONS................................................................................................................................... 8
2.3 | SAFETY FEATURES........................................................................................................................................................................ 9
2.4 | SAFETY INDICATORS & INTERLOCKS..................................................................................................................................... 9
2.5 | SAFETY CONTROLS....................................................................................................................................................................11
2.6 | MAINTENANCE LOCK............................................................................................................................................................... 12
2.7 | PROPOSITION 65....................................................................................................................................................................... 12
2.8 | SAFETY GUIDELINES ................................................................................................................................................................. 13
SECTION 3 PRODUCT DESCRIPTION...................................................................................................................................14
3.1 | GENERAL....................................................................................................................................................................................... 14
SECTION 4 DECALS..................................................................................................................................................................16
4.1 | DECAL LOCATIONS AND DESCRIPTIONS........................................................................................................................... 16
4.2 | DECAL SYMBOLS........................................................................................................................................................................ 18
SECTION 5 TRANSPORT, HANDLING & STORAGE............................................................................................................ 22
5.1 | PRELIMINARY UNPACKING INSTRUCTIONS AND DEALER INSPECTION ..................................................................22
5.2 | STORAGE......................................................................................................................................................................................22
5.3 | TRANSPORTATION ....................................................................................................................................................................22
5.4 | FORK LIFT POCKETS .................................................................................................................................................................22
5.5 | LIFTING AND TIEDOWN POINTS.........................................................................................................................................23
SECTION 6 OPERATION ......................................................................................................................................................... 24
6.1 | BEFORE YOU OPERATE............................................................................................................................................................24
6.2 | LOWER CONTROLS ..................................................................................................................................................................24
6.3 | UPPER CONTROLS AND INDICATORS................................................................................................................................25
6.4 | STARTUP/SHUTDOWN.............................................................................................................................................................26
6.5 | ELEVATING AND LOWERING.................................................................................................................................................. 27
6.6 | INFORMATION INDICATORS.................................................................................................................................................. 27
6.7 | ERROR ALARMS ..........................................................................................................................................................................28
6.8 | CHARGING THE BATTERY.......................................................................................................................................................30
SECTION 7 PRESTART INSPECTION CHECKLIST ............................................................................................................ 32
7.1 | PRESTART INSPECTION CHECKLIST ...................................................................................................................................32
NOTES........................................................................................................................................................................................ 34
PUSH-AROUND SERIES PA-1030
4

INDEX OF FIGURES
REVISION LOG:
REV A........................................................................................................................................................................................August 2020
INDEX OF FIGURES
FIGURE 1: Lanyard Attachment ..............................................................................................................................................................3
FIGURE 2: Manual Storage Location.....................................................................................................................................................6
FIGURE 3: Descent Warning Light.........................................................................................................................................................9
FIGURE 4: Automatic Brake...................................................................................................................................................................10
FIGURE 5: Auxiliary Lowering................................................................................................................................................................ 11
FIGURE 6: Lowering Instructions......................................................................................................................................................... 11
FIGURE 7: Maintenance Lock Use .......................................................................................................................................................12
FIGURE 8: Maintenance Lock Storage ...............................................................................................................................................12
FIGURE 9: Decal Locations ...................................................................................................................................................................16
FIGURE 10: Fork Lift Pocket.................................................................................................................................................................. 22
FIGURE 11: Tie-Down Points ................................................................................................................................................................ 23
FIGURE 12: Example Sling/Lifting........................................................................................................................................................ 23
FIGURE 13: Center of Gravity............................................................................................................................................................... 23
FIGURE 14: Base Controls..................................................................................................................................................................... 24
FIGURE 15: Platform Controls...............................................................................................................................................................25
FIGURE 16: Bubble Level....................................................................................................................................................................... 26
FIGURE 17: Rear Brake ........................................................................................................................................................................... 26
FIGURE 18: Padlock Example............................................................................................................................................................... 26
FIGURE 19: Battery Charger and Light Locations............................................................................................................................ 31
5
OPERATION & SAFETY MANUAL PA1.1-S REV A

SECTION 1 FAMILIARIZATION
1.1 | REQUIREMENT FOR CONFIRMATION OF MANUALS
Page Section
26 6.4 | START-UP/SHUTDOWN
FIGURE 2: Manual Storage Location
1.2 | PURPOSE AND FUNCTION OF CONTROLS
Page Section
11 2.5 | SAFETY CONTROLS
24 6.1 | BEFORE YOU OPERATE
27 6.5 | ELEVATING AND LOWERING
1.3 | NONOPERATING CHARACTERISTICS
FEATURES
Page Section
9 2.3 | SAFETY FEATURES
13 2.8 | SAFETY GUIDELINES
14 - 15 3.1 | GENERAL
16 - 20 4 | DECALS
23 5.5 | LIFTING AND TIE DOWN POINTS
22 5.4 | FORK LIFT POCKETS
26 6.4 | STARTUP/SHUTDOWN
PUSH-AROUND SERIES PA-1030
6

SECTION 1 FAMILIARIZATION
LIMITATIONS
Page Section
9 2.4 | SAFETY INDICATOR AND INTERLOCKS
13 2.8 | SAFETY GUIDELINES
14 - 15 3.1 | GENERAL
18 - 20 4.2 | DECAL SYMBOLS
22 5.2 | STORAGE
22 5.3 | TRANSPORTATION
22 5.5 | FORK LIFT POCKETS
26 6.4 | STARTUP/SHUTDOWN
28 6.7 | ERROR ALARMS
26 6.7 | CHARGING THE BATTERY
DEVICES
Page Section
9 2.4 | SAFETY INDICATOR AND INTERLOCKS
11 2.5 | SAFETY CONTROLS
12 2.6 | MAINTENANCE LOCK
14 - 15 3.1 | GENERAL
18 - 20 4.2 | DECAL SYMBOLS
22 5.3 | TRANSPORTATION
24 6.1 | BEFORE YOU OPERATE
26 6.7 | CHARGING THE BATTERY
1.4 | OPERATING CHARACTERISTICS
Page Section
9 2.4 | SAFETY INDICATORS AND INTERLOCKS
11 2.5 | SAFETY CONTROLS
12 2.6 | MAINTENANCE LOCK
14 - 15 3.1 | GENERAL
22 5.3 | TRANSPORTATION
26 6.7 | CHARGING THE BATTERY
7
OPERATION & SAFETY MANUAL PA1.1-S REV A

SECTION 2 SAFETY
2.1 | SAFETY SYMBOLS
FAILURE TO FOLLOW THIS WARNING WILL CAUSE
DEATH OR PERSONAL INJURY.
"DANGER" indicates an imminently hazardous
situation, which, if not avoided, will result in
death or serious injury.
FAILURE TO FOLLOW THIS WARNING MAY CAUSE
DEATH OR PERSONAL INJURY.
“WARNING” indicates a potentially hazardous
situation, which, if not avoided, could result in
death or serious injury.
FAILURE TO FOLLOW THIS WARNING MAY CAUSE
INJURY OR DAMAGE TO EQUIPMENT.
“CAUTION” indicates a potentially hazardous
situation which, if not avoided, could result
in minor or moderate injury or damage to
equipment.
2.2 | GENERAL RULES AND PRECAUTIONS
An operator of any type of work platform is subject to certain hazards that cannot be protected by mechanical
means. It is therefore essential that operators be competent, careful, physically and mentally fit, and
thoroughly trained in safe operation of this machine.
Although Custom Equipment, LLC conforms to specified ANSI, OSHA and CSA, it is the responsibility of the
owner to instruct operators with the safety requirements made not only by Custom Equipment, LLC, but
by the various safety boards in your area, as well as additional requirements set forth by ANSI and OSHA, or
CSA. If you come across a situation that you think might be unsafe, stop the platform and request further
information from qualified sources before proceeding.
DO NOT OPERATE MACHINE NEAR POWER LINES.
THE PLATFORM AND ENCLOSURES ARE NOT
INSULATED. EQUIPMENT IS ONLY AS SAFE AS THE
OPERATOR.
NEVER REACH BETWEEN SCISSORS LINKS OR PROP
UP PLATFORM.
PUSH-AROUND SERIES PA-1030
8

SECTION 2 SAFETY
2.3 | SAFETY FEATURES
2.4 | SAFETY INDICATORS & INTERLOCKS
Puncture-Proof Wheels
Guardrails
43.4 in (110.2 cm) height with 6 in (15 cm) toe guards.
Non-Slip Deck
Entrance Gate
Automatic Brake when Elevated
Free Descent Protection
A holding valve is installed in the manifold block to prevent the platform from descending in case of a
ruptured hydraulic hose. The platform is hydraulically locked until hose has been replaced.
Decals
Danger, Caution, and Warning decals are displayed at various locations on this unit.
Key Switch Security
To prevent unauthorized use, a key switch is required for operation.
Tilt Alarm
If the chassis is tilted more than 1.5°, elevating function is prevented, and an alarm sounds. Lower the
platform and move to a hard, level surface before elevating.
Descent Alarm & Lowering Interrupt
An audible alarm sounds when the machine is lowering.
When lowering the platform, the platform will stop when the ends of the scissors are approximately 2 inches
apart for 3 seconds. The beacon light flashes to indicate the armguard delay (if both are equipped). Release.
Look around all sides of the scissors to check for persons at risk. Then continue lowering the platform. If
elevating platform less than 2 inches, the lift will not descend due to the armguard feature. Elevate the
platform higher before lowering, or use the manual override in case of emergency.
FIGURE 3: Descent Warning Light
9
OPERATION & SAFETY MANUAL PA1.1-S REV A

SECTION 2 SAFETY
Slope Alarm
An audible alarm sounds when the stowed
machine is on a ramp.
Overload/Warning Alarm
An LED on the platform controls will activate when
the load for the platform approaches maximum
rating. An audible alarm will sound once the rated
load has been exceeded. (See the “Operation”
section of this manual for more detail).
Automatic Brakes
When elevated, a brake is automatically applied
to the rigid wheels. The manual parking brake on
the swivel casters should also be used. (See the
“Operation” section of this manual). FIGURE 4: Automatic Brake
PUSH-AROUND SERIES PA-1030
10

SECTION 2 SAFETY
2.5 | SAFETY CONTROLS
Auxiliary Lowering: Descent - Manual Override
For manually lowering the scissors in the case of power failure, a manual valve on the pump is provided. To
lower the scissors, pull the cable located at the rear or the machine.
FIGURE 5: Auxiliary Lowering FIGURE 6: Lowering Instructions
Emergency Stop
This lift is equipped with two emergency stop switches, one at the platform control and one at the base
control, that when activated, will render the unit inoperable until reset. To reset, pull the button out. (See the
“Operating Controls & Indicators” section of this handbook for more detail.)
IF PLATFORM SHOULD FAIL TO LOWER, DO
NOT ATTEMPT TO CLIMB DOWN THE BEAM
ASSEMBLY. SERIOUS INJURY MAY RESULT. HAVE AN
EXPERIENCED OPERATOR USE THE EMERGENCY
LOWERING PROCEDURE TO SAFELY LOWER THE
PLATFORM.
PUSHING THE EMERGENCY STOP MAY CAUSE
UNEXPECTED PLATFORM MOVEMENT AS THE
MACHINE COMES TO A SUDDEN STOP. BRACE
YOURSELF AND SECURE OBJECTS ON THE
PLATFORM DURING OPERATION OF THE MACHINE.
11
OPERATION & SAFETY MANUAL PA1.1-S REV A

SECTION 2 SAFETY
2.6 | MAINTENANCE LOCK
FIGURE 7: Maintenance Lock Use FIGURE 8: Maintenance Lock Storage
The maintenance lock must be placed into position whenever the machine is being serviced in a partially
raised position. Serious injury and/or death could result if maintenance lock is not used properly.
2.7 | PROPOSITION 65
THIS PRODUCT CONTAINS CHEMICALS KNOWN TO
THE STATE OF CALIFORNIA TO CAUSE CANCER,
AND BIRTH DEFECTS OR OTHER REPRODUCTIVE
HARM.
PUSH-AROUND SERIES PA-1030
12

SECTION 2 SAFETY
2.8 | SAFETY GUIDELINES
Only qualified operators may operate this unit
• All operators must read and understand the Operation and Safety Manual. They must understand all
decals and warning labels on unit.
• Do not work on platform if your physical condition is such that you feel dizzy or unsteady in any way.
• Do not neglect/misuse machine. Report any misuse of equipment to proper personnel.
• Prevent unauthorized use; when unit is not in use, remove key.
• It is recommended all personnel on unit wear approved personal protective equipment (PPE), i.e. head
gear.
Use machine only for purposes for which it was intended
• Lift should never be used as a crane.
• Do not exceed the load capabilities of the platform.
• Distribute load evenly over platform floor area.
• Never use unit as electrical grounds for arc welding.
• Do not override any hydraulic, mechanical, or electrical safety devices.
Check job site for unsafe working conditions
• Watch out for others. Keep others clear of operating platform. Never allow others to pass under a raised
platform or position the platform over someone.
• Avoid contact with fixed objects (walls, buildings, or other machinery, etc) or moving vehicles
(automobiles, cranes, etc).
• Follow any applicable national trac regulations.
• Never use outdoors. Lift is not designed for windy conditions or electrical storms.
• Unit must be on hard level surface before elevating. Do not operate on incline or uneven surface.
• You must maintain a clearance between any part of the machine, or its load, and any electrical line or
apparatus. Follow local power line clearance regulations.
DO NOT OPERATE MACHINE NEAR POWER LINES.
THE PLATFORM AND ENCLOSURES ARE NOT
INSULATED.
Equipment is only as safe as the operator
• Do not use ladders or scaolding on the platform to obtain greater height.
• Do not enter or exit platform while machine is in motion.
• Never mount or dismount a raised platform.
• Make sure entry gate is secured before operating machine from the platform.
• Never belt or tie o to an adjacent structure.
• Secure tools and materials.
• Personnel must maintain a firm footing on the platform floor and work only within the platform area.
• Never move the unit with a person in the platfom. Never move the unit in the elevated position.
Before operation, ensure that the machine is properly serviced
• Do not use machine if it is not working properly.
• Make sure platform rails and pins are secured.
• Operator shall use the maintenance lock when performing all types of maintenance procedures.
• Do not smoke while charging the battery.
• Perform inspections and preventative maintenance at the recommended intervals. (See the “Before you
operate” section of this handbook)
13
OPERATION & SAFETY MANUAL PA1.1-S REV A

SECTION 3 PRODUCT DESCRIPTION
Custom Equipment’s Hy-Brid Lifts are mobile elevating work platforms designed to be safe and reliable. The
purpose of the machine is to elevate personnel, along with their necessary tools and materials to overhead
work locations.
Manufacturer approval is required for any use other than the intended use.
Before operation, the operator must read and understand the manufacturer’s operating instructions and user’s
safety rules, or have them explained, understand all labels, warnings, and instructions displayed on the work
platform or have them explained, ensure that all occupant of the work platform wear appropriate protective
equipment for the conditions, including the environment in which the work platform will be operated.
The operator must inspect the workplace for environmental hazards such as, but not limited to drop-os,
holes, slopes, debris, floor or overhead obstructions, surface, wind and weather conditions, or presence of
unauthorized persons. Vibration does not create significant hazards on this machine.
SPECIFICATIONS PA-1030
Working Height 15.7 ft 4.78 m
Platform Height 9.7 ft 2.97 m
Stowed Height 68.7 in 174.5 cm
Platform Entrance 25.2 in 64.0 cm
Ground Clearance 2.6 in 6.6 cm
Overall Width 29.8 in 75.7 cm
Overall Length 51.3 in 130.3 cm
Platform (Inside) 20.5 in x 40.9 in 52.1 cm x 103.9 cm
Guard Rail Height 43.4 in 110.2 cm
Step Height 13.1 in 33.3 cm
Wheel Base 40.0 in 101.6 cm
Wheel Track 25.8 in 65.5 cm
Turning Radius (Inside) Zero Zero
Turning Radius (Outside) 48.8 in 124.0 cm
Tire Size (Solid, Non-Marking) -
Front / Rear 7.9 in / 7.9 in 20.0 cm / 20.0 cm
RATED LOAD
Lift Capacity (Evenly Distributed) 530 lbs 1 Person
240 kg
Horizontal/Manual Force 45 lbs 200 N
3.1 | GENERAL
PUSH-AROUND SERIES PA-1030
14

SECTION 3 PRODUCT DESCRIPTION
SPECIFICATIONS PA-1030
FLOOR LOADING
Machine Weight (Unloaded) (Approx.) 893.0 lbs 405.1 kg
Minimum Wheel Load - Contact Pressure 315.0 psi 2.1 MPa
Maximum Wheel Load - Contact Pressure 372.1 psi 2.6 MPa
Minimum Machine Loading -
Floor Loading Pressure 82.4 psf 3.9 kPa
Maximum Machine Loading -
Floor Loading Pressure 131.8 psf 6.3 kPa
ENVIRONMENTAL LIMITATIONS
Wind No Windy Conditions/Indoor Use Only
Rated Slope Level Surface
Tilt Sensor Activated 1.5°Longitudinally / 1.5° Latterally
Grade-ability (Stowed Position) N/A
Temperature -4°F to 104°F -20° C to 40° C
Vibration 8.2 ft/s² max 2.5 m/s2max
Sound - Normal Use, Alarms 86 dB Normal Use
POWER SYSTEMS  DRIVE SYSTEM (Proportional Electric)
Drive Speed (Platform Elevated) N/A
Drive Speed (Platform Lowered) N/A
Lift Speed/Lower Speed 18/20 sec
Hydraulic Pressure (Max) 1800.0 psi 12410.6 MPa
Hydraulic Fluid Capacity 0.8 gal 2.8 L
Power System - Voltage 12V DC
Batteries - Deep Cycle Marine (1) 12V Group 27 Wet Cell or AGM
15
OPERATION & SAFETY MANUAL PA1.1-S REV A

SECTION 4 DECALS
4.1 | DECAL LOCATIONS AND DESCRIPTIONS
FIGURE 9: Decal Locations
PUSH-AROUND SERIES PA-1030
16

SECTION 4 DECALS
ITEM NO. PART NO. SUF REV DECAL MEANING OR DESIGNATION QTY
1 177-21-080 -55-K C DECALS,PA-1030 1
1.1 DE1003 A DECAL,FORK 4
1.2 DE1008 A DECAL,HYDR FLUID 1
1.3 DE1031 A DECAL,MADE IN USA MIRROR 1
1.4 DE1207 A DECAL,HY-BRID LIFTS™1
1.5 DE1221 A DECAL,MADE IN USA 1
1.6 DE1315 A DECAL,CTL UPR 1
1.7 DE1229 A DECAL,CTL UPR E-STOP 1
1.8 DE1230 A DECAL,PROP 65 1
1.9 DE1231 A DECAL,SERIES PA 2
1.10 DE1232 A DECAL,WEBSITE 2
1.11 DE1243 A DECAL,E-DOWN CABLE 2
1.12 DE1246 A DECAL,MANUAL BOX 1
1.13 DE1248 A DECAL,LANYARD ATTACHMENT 1
1.14 DE1249 A DECAL,ANNUAL INSPECTION 1
1.15 DE1250 A DECAL,SCISSOR CRUSH HAZARD 2
1.16 DE1305 A DECAL,MAINT LOCK 1
1.17 DE1309 A DECAL,TOE BOARD, PA-1030 1
1.18 DE1310 A DECAL,CAPACITY,530#,1P,I,WO/SO 1
1.19 DE1311 A DECAL,LWR DANGERS 1
1.20 DE1312 A DECAL,CTL LWR PA-1030 1
1.21 DE1313 A DECAL,WHEEL LOAD PA-1030 4
2 DE1201 A DECAL,MODEL PA-1030 2
17
OPERATION & SAFETY MANUAL PA1.1-S REV A

• No Unauthorized Use
• Do not operate this machine unless you have been trained in
safe operation.
• Training includes complete knowledge of the safety and
operating instructions contained in the manufacturer’s
manual, your employer’s work rules, and applicable
government regulations.
• An untrained operator subjects himself and others to death or
serious injury.
• Read and understand all dangers and warning in the
Operations & Safety Manual before operating this machine.
• Improper use of this machine could cause death or serious
injury.
• Inspect machine and make sure that it is operating properly,
that all name plate and hazard signs are in place and
legible, and that the machine is in accordance with the
manufacturer’s maintenance requirements contained in
the operating and maintenance manual and the daily safety
checklist.
• Lanyard anchorage point location. Capacity 1 person
• Lanyard anchorage points are for work positioning restraints
only.
• Use of fall arrest systems attached to anchorage points on
mobile equipment may cause machine to tip, resulting in
serious injury or death.
• Crushing Hazard
• Do not enter the space beneath the work platform or scissor
structure unless the maintenance lock is in place.
• Refer to Maintenance & Troubleshooting Manual
• Only qualified service personnel may service the machine.
Failure to comply with listed safety precautions may result in
machine damage, personnel injury, or death.
• Replace designated items with manufacturer’s specified
equipment only. Failure to use these items may cause
instability and could void the Warranty.
• Batteries produce explosive gas. Charge batteries in a well-
ventilated area.
• Do not expose sparks or flames.
• Do not smoke while charging battery.
• Battery Charger Power Inlet
SECTION 4 DECALS
4.2 | DECAL SYMBOLS
PUSH-AROUND SERIES PA-1030
18

• Tip Hazard
• Tip Hazard
• Do not elevate platform on steps
• Tip Hazard
• Do not elevate platform on a slope.
• Tip Hazard
• Do not elevate platform on uneven or soft surfaces.
• Indoor Use Only: No Wind Load
• Electrocution Hazard
• This machine is not insulated.
• Maintain safe clearance from electrical lines and apparatus.
You must allow for machine sway, rock or sag and electrical
lines swaying.
• This machine does not provide protection from contact with
or proximity to an electrically charged conductor.
• You must maintain a clearance between any part of this
machine or its load and any electrical apparatus. Follow local
power line regulations.
• Death or serious injury will result from contact or inadequate
clearance.
SECTION 4 DECALS
19
OPERATION & SAFETY MANUAL PA1.1-S REV A

• Emergency Lowering
• For safety and controlled handling, it is not recommended to
move the unit on a slope greater than 5°.
• Fork pocket
• Hydraulic oil level
• Engaging Mechanical Action: Enable Switch
SECTION 4 DECALS
PUSH-AROUND SERIES PA-1030
20