HYDAC International ELF Guide

EN 7.404.E1/08.17
Spare Parts List
Air lter
with Filling Strainer ELF
Up to 5500 l/min
1. MAINTENANCE
1.1 GENERAL
Please follow the maintenance
instructions!
1.2 COMMISSIONING
Check that the correct filter element
is fitted, replace cover (only for ELF
5, 52, 7 and 72).
1.3 TOOLS REQUIRED FOR
MAINTENANCE
Size TOOLS
5, 52 Spanner AF width 17
7, 72 -
2. CHANGING THE ELEMENT
Air filters ELF 10, 4, 30, 3 and
ELFL 3 must be replaced
completely; it is not possible to
change the element on these filter
types, for technical reasons.
2.1 CHANGING THE ELEMENTS ELF 5, 52
1. Remove the nut and washer
2. Lift up cover
3. Remove element(s)
4. Insert new element(s)
5. Replace cover
6. Apply washer
7. Screw on nut
2.2 CHANGING THE ELEMENTS ELF 7, 72
1. Unscrew cover manually by turning
anticlockwise
2. Remove element(s)
3. Insert new element(s)
4. Screw the cover on again manually
NOTICE:
Contamination or incomplete pressure
release on disassembly can lead to
seizing of the bowl thread.
Filter elements which cannot be cleaned
must be disposed of in accordance with
environmental protection regulations.
ELF 7 ELF 52ELF 5ELF 30
ELF 4 ELF 10 ELF 3 ELFL 3 ELF 72

2
EN 7.404.E1/08.17
3. SPARE PARTS
3.1 SPARE PARTS DRAWING ELF 3, 30, 4, 10 (ELFL 3)
3.2 SPARE PARTS LIST ELF 3, 30, 4, 10 AND ELFL 3
Item Description consists Part no.
1. Seal kit E ELF....3 F 1.0 2 + 1 seals made from Perbunan 00318971
Seal kit E ELF....3 F 1.0 /-RV-NBR 2 seals made of Perbunan + 1 seal made of Perbunan 00318968
Seal kit E ELF...30 F 1.0 2 seals made of Perbunan + O-ring 01285048
Seal kit E ELF...30 F 1.0 /-RV
Seal kit E ELF....4 F 1.0 2 seals made of cardboard 01261598
Seal kit E ELF...10 F 1.0 2 seals made of Perbunan + O-ring 01285050
2. Filling strainer E ELF....3 F 1.0 Filling strainer + 2 seals made of Perbunan + 6 screws 01261627
Filling strainer E ELF...30 F 1.0 Filling strainer + 2 seals made of Perbunan + 6 screws 01261627
Filling strainer E ELF....4 F 1.0 Filling strainer + 2 seals made of cardboard + 3 screws 01261628
Filling strainer E ELF....10 F 1.0 Filling strainer + 2 seals made of Perbunan + 3 screws 01261628
3. Top section ELF 3 (3 µm) – 00418479
Top section ELF 30 (3 µm) BF P 30 M 3 W 1.0 01286298
Top section ELF 4 (3 µm) – 00418549
Top section ELF 10 (3 µm) BF P 10 M 3 W 1.0 01284377
Top section ELFL 3 (3 µm) – 01315595
Other spare parts on request
1.
2.
3.
1.
2.
3.
1.
2.
3.
1.
2.
3.
ELF 3 (ELFL 3 *)
ELF 30
ELF 4
ELF 10
* not shown

3
EN 7.404.E1/08.17
3.3 SPARE PARTS DRAWING ELF 5, 52
3.4 SPARE PARTS LIST ELF 5, 52
Item Description 5 52
1. Filter element See Point 4 Replacement elements
0005 L 003 P 1 x 00309450 2 x 00309450
0005 L 003 P /-V 1 x 00315827 2 x 00315827
0005 L 003 BN 1 x 00315193 2 x 00315193
2. ELF 5(2) G XX W 2.0 (without element) 00308862 01271492
ELF 5(2) G XX W 3.0 (without element) 00312424 01283520
ELF 5(2) G XX W 4.0 (without element) 00314562 01283521
ELF 5(2) G XX W 5.0 (without element) 00314963 01283532
3. Filling strainer E ELF....5 G 2.0 (G2 1/2) 01303981
Filling strainer E ELF....5 G 3.0 (G3) 01303982
Filling strainer E ELF....5 G 4.0 (G2) 01294099
Filling strainer E ELF....5 G 5.0 (G1 1/2) 01291325
4. Cover E BF....5(2) W 1.0 01250862 01283650
Other spare parts on request
ELF 5
ELF 52
4.
1.
2.
3.
1.
2.
3.

4
EN 7.404.E1/08.17
3.5 SPARE PARTS DRAWING ELF 7, 72
3.6 SPARE PARTS LIST ELF 7, 72
Item Description 7 72
1. Filter element See Point 4 Replacement elements
0007 L 003 P 00310948 -
0072 L 003 P - 01293285
2. ELF 7 F XX W 1.0 (without element, without pressure gauge) 00311824 -
ELF 7 F XX K 1.0 (without element, with pressure gauge) 00314153 -
ELF 7 F XX UBM 1.0 (without element, with indicator) 01294579 -
ELF 72 F XX W 1.0 (without element, without pressure gauge) - 01292192
ELF 72 F XX UBM 1.0 (without element, with indicator) - 01302584
3. Filling strainer E ELF....3 F 1.0 01261627
4. Seal kit E ELF....3 F 1.0 00318971
5. Cover E BF....7 W 1.0 (without pressure gauge) 01250863 01283532
Cover E BF....7 K 1.0 (with pressure gauge) 01261600
Cover E BF....7 UBM 1.0 (with indicator) 01282542
Cover E BF...72 W 1.0 (without pressure gauge) - 01293286
Cover E BF...72 UBM 1.0 (with indicator) - 01285054
Other spare parts on request
ELF 7
ELF 72
5.
1.
2.
3.
1.
2.
3.
4. REPLACEMENT ELEMENT
0005 L 003 P
Size
0005, 0007, 0072
Type
L
Filtration rating
P: 003
BN: 003 (only for 0005)
Filter material
P, BN

5
EN 7.404.E1/08.17
5. MAINTENANCE INSTRUCTIONS
5.1 USER INSTRUCTIONS FOR
FILTERS
Notice
It is the responsibility of the
operator to comply with the
water regulations of the
country concerned.
Caution
Statutory accident prevention
regulations, safety
regulations and safety data
sheets for fluids must be
observed.
Caution
When working on, or in the
vicinity of, hydraulic
systems, naked flames,
sparks and smoking are
forbidden.
Caution
Hydraulic oils and water-
polluting fluids must not be
allowed to enter the soil or
watercourses or sewer
systems. Please ensure safe
and environmentally friendly disposal
of hydraulic oils. The relevant
regulations in the country concerned
with regard to ground water pollution,
used oil and waste must be complied
with.
Not suitable for cleaning
with high-pressure cleaner!
5.2 MAINTENANCE, GENERAL
This section describes maintenance
work which must be carried out
periodically. The operational safety
and life expectancy of the filter, and
whether it is ready for use, depend to
a large extent on regular and careful
maintenance.
5.3 MAINTENANCE MEASURES
• Spare parts must fulfil the technical
requirements specified by the
manufacturer.
This is always ensured when using
original HYDAC spare parts.
• Keep tools, working area and
equipment clean.
• After disassembling the filter, clean all
parts, check for damage or wear and
replace parts if necessary.
• When changing a filter element, a high
level of cleanliness must be observed!
5.4 INTERVAL BETWEEN ELEMENT
CHANGES
We recommend that you change the air
filter or the air filter element every time
you change the element.
We differentiate between air filters which
have to be completely replaced
(ELF 10, 3, 30, 4 and ELFL 3) and those
with a replaceable filter element
(ELF 5, 52, 7 and 72).
NOTE
The information in this brochure
relates to the operating conditions and
applications described.
For applications or operating conditions
not described, please contact the
relevant technical department.
Subject to technical modifications.
Customer Information in respect of
Machinery Directive 2006/42/EC
Hydraulic filters are fluid power parts/
components and are therefore excluded
from the scope of the Machinery Directive.
They do not bear the CE mark.
Before using these components, ensure
compliance with the specifications
provided by HYDAC Filtertechnik GmbH in
this documentation.
The specifications also contain information
on the relevant essential health and
safety requirements (based on Machinery
Directive 2006/42/EC) that are to be
applied by the user.
We hereby declare that the filters are
intended to be incorporated into machinery
within the terms of the Machinery Directive
2006/42/EC.
It is prohibited to put the filters into
service until the machinery as a whole is
in conformity with the provisions of the
Machinery Directive. Furthermore, our
Terms of Sale and Delivery are available
on our website (www.hydac.com).
SERVICE ADDRESSES
HYDAC Service GmbH
Postfach 1251
66273 Sulzbach / Saar, Germany
Factory address:
Werk 13
Friedrichsthaler Str. 15
66540 Neunkirchen / Heinitz
Germany
ServiCenter:
Tel.: [phone]
Fax: [phone]
Customer service:
Tel: [phone] / 509-412
Fax: [phone] / 509-828