Hypercom T77 Series User manual

Connecting the T77 Directly to a Phone Jack
The T77 requires an operating telephone line and a
convenient area for operating the terminal. Insert the
cable that came with the terminal into a dedicated
analog telephone jack. (The use of a different cable
might result in improper operation.) Insert the other end
of the telephone line into the port labeled LINE on the
back panel of the terminal. Ensure that the telephone
line latches are firmly locked into the jacks on the
terminal and the wall receptacle.
Note: Hypercom terminals do not function
with digital phone lines.
Connecting the T77 With a Telephone
Connect one end of the telephone line to the back of the
telephone and connect the other end to the port labeled
PHONEon the back panel of the terminal. When the
line is connected, lift the handset and listen for a dial
tone. If you do not hear a dial tone, check the
connection again. The terminal displays
REPLACE HANDSET when the phone is
in use and cannot perform dial transactions.
Powering up the T77
Connect the power (+24 Vdc) cable from the AC
Adapter to the three-pin port labeled POWERon the
back panel of the terminal. (The use of a different power
supply other than the one supplied with the unit may
result in improper operation.) Plug the Adapter into a
110-Volt grounded power receptacle. Be sure the
connector is firmly seated. When the power is connected
successfully, the terminal beeps twice and performs a self-
test and diagnostic routine. The software and downline
load status of the terminal is displayed during the self-
test, which takes approximately four seconds.
T 77 Series
TERMINAL
INSTALLATION
GUIDE
Phone
Power
Line
Introduction to the T77 Series Terminals
The T77 terminal series includes the T77F, T77S, T77G, T77Q, T77T and
T77GQ. With their high speed easily replaceable printer modules, the T77
terminal series are perfect for a wide range of applications. The T77 series supports
draft capture, debit, check and proprietary card processing. They also support new
payment vehicles such as chip card-based credit/debit cards and stored value cards.
Setup and Maintenance
Inserting the Printer Ribbon and Printer Module
Release the two tabs on the tear bar cover, located at the
back of the terminal, by placing fingers on the tabs and
pulling the cover up.
Locate the gray levers on the back of the terminal
and push them down and away from you.
Carefully remove the modular printer by pulling
the printer mechanism away from the terminal.
Do not use the paper holder for leverage.
Tighten the new ribbon by rotating the ribbon
feed knob in the direction shown by the arrow
on the ribbon cassette. Place the new cassette
on the printer module allowing the ribbon to
slip into the printing gap.
Place the printer module into the terminal and
evenly slide the mechanism under the guides in
the bottom of the printer chassis until it stops.
Then, use the gray levers to guide the
mechanism into the terminal by pulling the
levers toward you.
Close the tear bar cover, then the paper cover,
and connect the power supply.
Lever Lever
Guide Guide
Ribbon
Cassette
[T7XXXXX] DLL-00
WAIT -SELF-TEST

© Hypercom Corporation, 1998. Printed in the United States of America.
·
Disconnect the AC electric power before replacing the ribbon
or printer module.
·
Do not use an Adapter, power extender Adapter, power extender
cable, or an AC outlet that does not have a ground connection.
·
Do not disassemble the AC Adapter. The Adapter should be
serviced only by qualified service personnel.
·
The AC Adapter has been designed for indoor use only.
·
Do not expose to rain or snow.
·
Do not immerse in fluid.
·
The reliability of electronic equipment is significantly reduced
whenever it is powered from an ungrounded outlet.
940152-001
Rev. B
10/98
Supply Information
If you are unable to purchase items through your processor such as
paper, ribbon, covers, and cables, contact Hypercom Supply Sales at
[phone].
Volume pricing available.
W arning
!
Inserting the Paper
T77F/T77T Paper Roll - Insert the paper roll
and dowel in the basket so the paper feeds
from under the roll, not over the top, and
has a straight-line path into the printer
paper-feed mechanism. Feed the paper
evenly into the paper-feed slot at the rear of
the T77 while pressing the PAPER FEED*
key. After the feed mechanism begins to
operate, the paper appears at the top of the
tear guide. Release the PAPER FEED key.
Press the key sequence Function, 8, 2,
Enter to perform a printer test. The printer
is now ready to print receipts.
T77S Sprocket Paper - Hold the bundle of
receipt paper so the first receipt is right-side
up with the printed text facing you. Place
the bundle in the paper holder. Pull the
paper guide toward you and insert the first
receipt face-downward into the slot
between the paper holder and the paper
guide. Press the PAPER FEED* key. After
the feed mechanism begins to operate, the
paper appears at the tear guide. Release the
PAPER FEED key. Use the paper release
lever to align the top of the colored portion
of the receipt to the top of the tear guide,
then push the paper guide back into
position. Press the key sequence Function,
8,2,Enter to perform a printer test. The
printer is now ready to print receipts.
* For the T77GQ terminals, with
the QWERTY keyboard, press CTRL
and Space Bar.
Release Lever
Tear Guide
Paper Load
Complete
Paper Load
Complete