Hytronik HIR27 Quick guide

HIR27-20210813-A0
3. Functions
Semi-auto Mode (Absence Detection)3.3
With the help of push-switch, this sensor can be over-ridden by the end-user to manually switch
on/off the light, which makes the product more user-friendly and offers more options to fit some
extra-ordinary demands:
Manual Override
3.2
* Short Push (<1s): on/off function;
On →Off: the light turns off immediately and cannot be triggered ON by motion until the expiration
of pre-set hold-time. After this period, the sensor goes back to normal sensor mode.
Off →On: the light turns on and goes to sensor mode, no matter if ambient Lux level exceeds the
daylight threshold or not.
* Long Push (>1s): adjust the target lux level by turning the light up or down. Both the adjustment on
remote control and push switch can overwrite each other. The last adjustment remains in memory.
Note: if end-user do not want this manual override function, just leave the “push” terminal
unconnected to any wire.
Wire Preparation
Pluggable screw terminal. It is recommended to make
connections to the terminal before fitting to the sensor.
0.75 - 2.5mm
8mm
(min 6mm, max 11mm)
1. Technical Specifications
Stand-by power
220~240VAC 50/60Hz
Mains voltage
<0.5W
Appr. 20s
PIR detection
Sensor principle
Warming-up
Operation temperature Ta: -20°C ~ +50°C
IP20
IP rating
360°
Detection angle
EMC standard (EMC)
Safety standard (LVD)
Certification
EN55015, EN61000, EN61547
CB, CE , EMC, LVD, RCM, ROHS compliance
EN60669-1, EN60669-2-1, AS/NES60669-1/-2-1
Detection range (Max.)*
HIR27
Detection range (Max.)*
HIR27/H
Installation height：15m (forklift)
12m (person)
Detection range (Ø)：24m
Installation Height : 6m
Detection Range (Ø) :9m
Installation height：15m (forklift)
12m (person)
Detection range (Ø)：40m
Detection range (Max.)*
HIR27/R
Installation Height : 6m
Detection Range(Ø) :10m
Detection range (Max.)*
HIR27/RH
Installation and Instruction Manual
HIR27 HIR27/R
HIR27/H HIR27/RH
FLUSH MOUNT PIR MOTION SENSOR
One DALI Channel Output
Switched power Max. 40pcs devices, 80mA
Daylight sensor measures the available surrounding natural light, calculates how much electrical light is
needed to reach the total lux expected. The demand is given to the LED driver by DALI signal, so as to
deliver the needed amount of electric light.
3.1 Daylight Harvest (Daylight Regulating)
0 24
Light level
Time (hrs)
Normal Electric Light
Daylight controlled light
Energy Saving Zone
Natural light
Hold time
Stand-by time
Selecting this mode will activate the following logic:
Manual on - The lights will not switch on until they have manually been switched on at the wall switch.
The occupancy sensor is inactive whilst the lights are off.
Auto off - When the lights are on, the sensor becomes active and monitors the space for activity. Once
the area is vacated (absence setection), the sensor will automatically switch off the lights if
the last person out forgets to switch off the light manually.
Note: The wall switch can be assigned to function
3.2 or 3.3 , but not both. The default function is
manual override.
By connecting the “SYNC” terminals in parallel (see wiring diagram), no matter which sensor detects
motion, all HIR27 in the group will turn on the lights when surrounding natural light is below the daylight
threshold. The detection area could be widely enlarged in this way.
Synchronisation Function3.4
2. Installation
78
75.2
70.5
62
4
2
3
1
65mm
* Install lens as required
7
21
5
* Install blind as required
A B
6
1. Ceiling (drill hole 65mm)
2. Carefully prise off the cable clamps.
3. Make connections to the pluggable
terminal blocks.
4. Insert plug connectors and secure using
the provided cable clamps, then clip
terminal covers to the base.
5. Fit detection blind (if required) and
desired lens.
6. Clip fascia to body.
7. Bend back springs and insert into ceiling.
3
2
1

4. Wiring Diagram
HIR27-20210813-A0
LED Driver LED Driver
LED DriverLED Driver
Description of the Button Functions (remote control HRC-11)5.
Ambient daylight threshold [ button ]
1. Press button Shift, the red LED starts to flash.
2. Press button , the ambient lux level is sampled and set as
the new daylight threshold / target Lux level.
3
10
10
Auto Mode [ button ]
Press button to initiate automatic mode. The sensor starts working
and all settings remain as before the light is switched ON/OFF.
4
4
Scene prog. [ zone ] (One-key-commissioning)
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, / “Daylight threshold”,
“Hold time” to set all parameters.
3. Press button “Memory” to save all the settings programmed in the
remote control.
7
8 9
10
7
11
Semi-auto Mode [ button & ]
1. Press button Shift (the red LED is on for indication).
2. Press button to initiate semi-auto mode. The fixture is manually
on by push-switch and automatically off in semi-auto mode.
3
3
4
4
Permanent ON/OFF [ ]
Press button , to select permanent ON or permanent OFF mode.
* Press button / to to quit this mode.
The mode will change to AUTO Mode after power failure.
button
1
1
2 4
Daylight threshold [ zone ]
Press buttons in zone to set daylight sensor at 2Lux/ 10Lux /
50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: To set daylight sensor at 100Lux / 300Lux / 500Lux, press
Shift button first.
9
9
3
Hold time [ zone ]
Press buttons in zone to set the hold time at 2s / 30s / 1min /
5min / 10min / 15min / 20min / 30min.
Note: 1.To set hold-time at 30s / 5min / 15min / 30min, press button
Shift at first.
2. 2s is for test purpose only, stand-by period and daylight
sensor settings are disabled in this mode.
*To exit from Test mode, press button or any button in zone .
3
11
11
11
2
HRC-11
6
8
10
11
12
13
14
2
4
1
3
7
9
5
Shift [ button ]
Press button , the LED on the top left corner is on to indicate mode
selection. All values / settings in RED are in valid for 20 seconds.
3
3
Detection range [ zone ]
8
These two buttons are disabled.
Button “Dual-tech & RF mode” is disabled.
7
7
7
7
3
8
10 11
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold
Disable, hold time 5min, the steps should be:
Press button Start, button 100%, Disable, Shift, 5min,
Memory. By pointing to the sensor unit(s)
and pressing Apply, all settings are passed on the sensor(s).
&
A
4
4 hhh
RESET[ button ]
Press button , all settings go back to default values as below:
2
2
Hold-time 5min, Daylight sensor 100Lux, Stand-by time: 10min, Stand-by
dimming level: 20%
Brightness +/- [ button ]
6
6
Press button to adjust the light brightness between 10%~100%.
Power output [ button ] (Daylight harvest without occupancy)
5
1. Press button , the red LED is on for indication.
2. Press button “Twilight”, the function of movement detection is
disabled.
Note: the function of “Sensor off” is disabled.
3
Stand-by time [ zone ]
Press buttons in zone to set the stand-by period at 0s / 10s /
1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control, 100%
on when motion detected, and remains at the stand-by dimming
level when no presence after hold-time.
12
12
Stand-by dimming level [ zone ]
Press buttons in zone to set the stand-by dimming level at 10% /
20% / 30% / 50%.
Note: the function of 24h/12h/4h/30s are disabled.
13
13

HIR27-20210813-A0
6. Detection Pattern & Optional Accessories
Radial (B)
Tangential (A)
2.5m
Mount height
6m
5m
4m
3m
insensitive sensitive insensitive sensitive
A: Tangential movement
Tangential: max. 9m
h = max.6m
A
B: Radial movement
Radial: max. 4m
h = max.6m
B
HIR27: Low-bay flat lens detection pattern for single person @ Ta = 20ºC
(Recommended ceiling mount installation height 2.5m-6m)
max 64m
2
(Ø = 9m) max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
max 50m
2
(Ø = 8m)
max 38m
2
(Ø = 7m)
max 38m
2
(Ø = 7m)
max 38m
2
(Ø = 7m)
Optional Accessory --- Ceiling/Surface Mount Box: HA03
1. HIR27 (Low-bay)
Valid Range
Blind Option 1 --- Aisle Detection
Optional Accessory --- Blind Insert for Blocking Certain Detection Angles
75
Ø 94
Blind Option 2 --- 180º Detection
Valid Range
44
66
4.2

HIR27-20210813-A0
Radial (B)
Tangential (A)
2.5m
Mount height
6m
5m
4m
3m
HIR27/R: Low-bay convex lens detection pattern for single person @ Ta = 20ºC
(Recommended ceiling mount installation height 2.5m-6m)
max 79m
2
(Ø = 10m)
max 79m
2
(Ø = 10m)
max 64m
2
(Ø = 9m)
max 50m
2
(Ø = 8m)
max 50m
2
(Ø = 8m)
max 20m
2
(Ø = 5m)
max 20m
2
(Ø = 5m)
max 20m
2
(Ø = 5m)
max 20m
2
(Ø = 5m)
max 20m
2
(Ø = 5m)
2. HIR27/R (Reinforced Low-bay)
A: Tangential movement
Tangential: max. 10m
h = max.6m
A
B: Radial movement
Radial: max. 5m
h = max.6m
B
Optional Accessory --- Ceiling/Surface Mount Box: HA03
Optional Accessory --- Blind Insert for Blocking Certain Detection Angles
75
Ø 94
Valid Range
Blind Option 1 --- Aisle Detection Blind Option 2 --- 180º Detection
Valid Range
insensitive sensitive insensitive sensitive
44
66
4.2

HIR27-20210813-A0
Blind Option 1 --- Aisle Detection Blind Option 2 --- 180º Detection
3. HIR27/H (High-bay)
Tangential: max. 20m
h = max.12m
A
Radial: max. 3m
h = max.12m
B
Radial (B)
Tangential (A)
10m
Mount height
14m
15m
13m
12m
11m max 452m
2
(Ø = 24m)
max 380m
2
(Ø = 22m)
max 452m
2
(Ø = 24m)
max 452m
2
(Ø = 24m)
max 452m
2
(Ø = 24m)
max 452m
2
(Ø = 24m)
max 201m
2
(Ø = 16m)
max 201m
2
(Ø = 16m)
max 201m
2
(Ø = 16m)
max 177m
2
(Ø = 15m)
max 133m
2
(Ø = 13m)
max 113m
2
(Ø = 12m)
A: Tangential movement
Tangential: max. 24m
h = max.15m
A
B: Radial movement
Radial: max. 16m
h = max.15m
B
HIR27/H: High-bay lens detection pattern for forklift @ Ta = 20ºC
(Recommended ceiling mount installation height 10m-15m)
Optional Accessory --- Ceiling/Surface Mount Box: HA03
Optional Accessory --- Blind Insert for Blocking Certain Detection Angles
Valid Range Valid Range
Radial (B)
Tangential (A)
2.5m
Mount height
11m
12m
10m
8m
6m max 104m
2
(Ø = 11.5m)
max 50m
2
(Ø = 8m)
max 154m
2
(Ø = 14m)
max 227m
2
(Ø = 17m)
max 269m
2
(Ø = 18.5m)
max 314m
2
(Ø = 20m)
max 7m
2
(Ø = 3m)
max 7m
2
(Ø = 3m)
max 7m
2
(Ø = 3m)
max 7m
2
(Ø = 3m)
max 7m² (Ø = 3m)
max 7m² (Ø = 3m)
A: Tangential movement B: Radial movement
HIR27/H: High-bay lens detection pattern for single person @ Ta = 20ºC
(Recommended ceiling mount installation height 2.5m-12m)
insensitive sensitive insensitive sensitive
insensitive sensitive insensitive sensitive
75
Ø 94
44
66
4.2

HIR27-20210813-A0
7. Additional Information / Documents
1. Regarding precautions for PIR sensor installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->PIR Sensors - Precautions for Product Installation and Operation
2. Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy
Radial (B)
Tangential (A)
10m
Mount height
14m
15m
13m
12m
11m
max 907m
2
(Ø = 34m)
max 962m
2
(Ø = 35m)
max 1075m
2
(Ø = 37m)
max 660m
2
(Ø = 29m)
max 346m
2
(Ø = 21m)
max 1256m
2
(Ø = 40m)
max 154m
2
(Ø = 14m)
max 177m
2
(Ø = 15m)
max 177m
2
(Ø = 15m)
max 154m
2
(Ø = 14m)
max 113m
2
(Ø = 12m)
max 113m
2
(Ø = 12m)
A: Tangential movement
Tangential: max. 40m
h = max.15m
A
B: Radial movement
HIR27/RH: Reinforced high-bay lens detection pattern for forklift @ Ta = 20ºC
(Recommended ceiling mount installation height 10m-15m)
Radial: max. 15m
h = max.15m
B
Optional Accessory --- Ceiling/Surface Mount Box: HA03
4. HIR27/RH (Reinforced High-bay with 3-Pyro)
Tangential: max. 30m
h = max.12m
A
Radial: max. 4m
h = max.12m
B
Radial (B)
Tangential (A)
2.5m
Mount height
11m
12m
10m
8m
6m max 154m
2
(Ø = 14m)
max 38m
2
(Ø = 7m)
max 314m
2
(Ø = 20m)
max 531m
2
(Ø = 26m)
max 615m
2
(Ø = 28m)
max 707m
2
(Ø = 30m)
max 7m
2
(Ø = 3m)
max 7m
2
(Ø = 3m)
max 7m
2
(Ø = 3m)
max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
A: Tangential movement B: Radial movement
HIR27/RH: Reinforced high-bay lens detection pattern for single person @ Ta = 20OC
(Recommended ceiling mount installation height 2.5m-12m)
insensitive sensitive insensitive sensitive
insensitive sensitive insensitive sensitive
75
Ø 94
44
66
4.2