Hytronik HIR32 User manual

HIR32
Flush Mount PIR Motion Sensor
Independent DALI Occupancy Sensor with Daylight Harvest
PIR
IP40
Applications
Ofce, classroom and commercial interior spaces where DALI control is required in
small groups.
Ofce / Commercial Lighting
Classrooms
Stairwells / Corridors
HIR32 with DALI Broadcast Output
Designed with a low prole for aesthetically demanding architectural projects
whilst retaining the functionality expected of the latest lighting controls. Control
to the light xtures is provided via self-powered DALI communication (up to 40 drivers).
Set-up of the sensor is carried out using a remote control handset with program memory
allowing one-key commissioning where common settings are used for multiple devices.
EMC standard (EMC)
Safety standard (LVD)
Certication
EN55015, EN61000
CB, CE , EMC, RCM
EN60669, AS/NZS60669
Safety and EMC
Technical Data
Input Characteristics
Stand-by power
Operating voltage
<0.5W
220~240VAC 50/60Hz
Output Characteristics
DALI Channel 1
30mA, Max. 15 LED drivers
DALI Channel 2
50mA, Max. 25 LED drivers
Suitable for DALI DT8 LED drivers
Operation temperature
Ta: - 20° C~ + 50° C
Environment
IP40
IP rating
One-Key
Commissioning
Photocell
Intelligent
5-year warranty
Features
Daylight harvest function to regulate light output for maintaining required lux level.
DALI dimming control based upon occupancy.
Store settings in the remote for easy commissioning when programming multiple sensors.
Intelligent photocell - lights and sensors only operate when needed, natural light has proirity.
5m (maximum)
360°Detection angle
Mounting height
PIR Sensor Data
Approximately 20s
Warm-up Period
Detection range (Max.)*
HIR32/H
Installation height：15m (forklift)
12m (person)
Detection range (Ø)：18m
Detection range (Max.)*
HIR32
Installation Height : 5m
Detection Range(Ø) :10m@3m height

Wire Preparation
Pluggable screw terminal. It is recommended to make
connections to the terminal before tting to the sensor.
0.75 - 2.5mm
8mm
(min 6mm, max 11mm)
Machanical Structure
Photocell
Intelligent
TM
75.2
78
70.5
62
1. Ceiling (drill hole65mm)
2. Carefully prise off the cable clamps.
3. Make connections to the pluggable
terminal blocks.
4. Insert plug connectorsand secure using
the provided cableclamps, then clip
terminal covers to the base.
5. Fitdetection blind (if required) and
desired lens.
6. Clip fascia to body.
7. Bend back springs and insert into ceiling.
4
5
2
3
1
65mm
* Install lens as required
* Install blind as required
A B
7
21
6
Note:We recommend the mounting distance between sensor to sensor should be more than 2m to prevent sensors
from false-triggering.
321
Optional accessory--- Ceiling/Surface Mount Box: HA03
Ceiling mount version
open
95
65
77.1
82.3

Occupancy Detection
Wiring Diagram
HIR32
Max.15pcs
Max.25pcs
DA DA
LED Driver
LED
- + L N
DA DA
LED Driver
LED
- + L N
DA DA
LED Driver
LED
- + L N
DA DA
LED Driver
LED
- + L N
DA1 DA2
L
N
P3 P2 P1 NL
Detection range with convex lens Detection range with at lens
Tangential movement up to10m
Radial movement up to 5m
3m
3m
Tangential movement up to 5m
Radial movement up to 2.5m
Tangential movement up to 9m
Radial movement up to 4m
3m
3m
Tangential movement up to 4.5m
Radial movement up to 2m
A
Detection range with convex lens and 50% Blind A Detection range with at lens and 50% Blind A
Up to 8m
Up to 2m
3m
Up to 7m
Up to 2m
3m
B
Detection range with convex lens and corridor blind B Detection range with at lens and corridor blind B

2
The light dims down and
eventually turns off when
the ambient natural light is
sufcient.
The light switches off
completely after hold-time.
The built-in photocell performs the function of reading the natural daylight, and maintaining the lux level by calculating how much
articial light is needed according to the target lux level required by the prole preset.
Ofce Application
Daylight Harvest and Lux Off Function
Light will not switch on
when natural light is
sufcient, even there is
motion detected.
The light switches on
automatically with
presence when natural
light is insufcient.
The light turns on at full or dims to maintain the lux level. The light output
regulates accroding to the level of natural light available.
1
The light goes to stand-by
time after hold-time and
stays on dimming level.
Functions and Features
Two channels of self-powered DALI output are available on HIR32 for connection of two groups of LED drivers. Please note that both
channels share the same control settings sent from the occupancy sensor and photocell.
Dual DALI Output Control
25 pcs
15 pcs
DALI channel
DALI PSU Channel 1 (max 50mA)
DALI PSU Channel 2 (max 30mA)
System Capacity
HIR32 includes 2 channels
total 80mA max. DALI PSU
DALI Driver < 2mA
High Bay Version HIR32/H
PIR tangential movement 18m
12m (person)
15m (forklift)

Three push terminals (P1, P2, P3) are available on the HIR32 for end-users to switch on/off, change the light brightness, colour
temperature of the two DALI channels temporarily. The settings will revert to daylight harvest mode after sensor time-out.
* Long push on P1: adjust the hold-time light brightness of DALI channel 1;
Short push (<1s) on P1: on/off function
* Long push on P2: adjust the hold-time light brightness of DALI channel 2;
Short push (<1s) on P2: on/off function
* Long push on P3: cycles through colour tuning on both channels. (work with DT8 LED driver only)
Short push (<1s) on P3: resume automatic daylight harvest mode .
Manual Override (Push Function)
3
Settings (Remote Control HRC-11)
Press button “RESET”, all settings go back to default:
Hold-time 5min, Daylight sensor 100Lux, Stand-by time: 10min, Stand-by dimming
level: 20%
Reset Settings
Test Mode
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
Note: the function of Semi-auto is disabled.
ON/
OFF
Brightness +/-
&
A
4
4 hhh
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button
1. Press these two buttons to adjust the light output brightness and set a new target lux level. The daylight sensor can measure ambient
daylight level and ignore the LED light, so as to calculate how much articial light is needed to maintain the target lux level.
2. Press “Shift” button rst, then press “+/-” button for colour tuning (work with DT8 LED driver only).
This button is for testing purpose only. The sensor goes to test mode (hold-time is 2s)
after commissoning, meanwhile the stand-by period and daylight sensor are disabled.
* This mode can be ended by pressing “reset”, or any button of “scene mode” and
“hold-time”. The sensor settings are changed accordingly.
1. Press button “Shift”, the red LED ashes for indication.
2. Press button “SEMI-AUTO/AUTO” to initiate semi-auto mode. The xture is
manually turned on by pressing the push-switch, and goes off automatically after
stand-by time. (Absence detection mode)
SEMI-AUTO mode
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
Power output

Detection range
All buttons are disabled, the detection range is default to maximum.
Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 100Lux / 300Lux / Disable.
Daylight threshold
1. Press button “Shift”, the red LED starts to ash.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.
Ambient daylight threshold
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Dual tech & RF mode
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the stand-by dimming level
when no presence after motion hold-time.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
All buttons are disabled.
Auto-conguration function
All buttons in this zone are disabled.
Scene program - 1-key commissioning
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
Note:We recommend customers to calibrate device real-time on yearly-based or half-yearly based by opening the App and
connecting to the network, in order to eliminate accumulated time error and make sure all time-related functions to work well.