Hyundai C2017 ADU01 User manual


Vacuum Cleaner
1/4" Drill Bit
Deburring Tool
Drill Stop
Masking Tape
Note:
- Accessory Installation
Model Year
2015 ~
Basic Required Hand Tools
Difficulty
( B )
Instructional Symbols / Definitions
Part No.
C2017 ADU01
C2017 ADUP1
Difficulty stated above reflects the minimum level of expertise required to install
the accessory.
( A ) Customer ( B ) Dealer Technician ( C ) Master Technician
Rust Inhibitor (Primer)
HYUNDAI Genuine Accessories
Vehicle Model
Sonata
Accessory
Cargo Net
Clip Removal Tool
Electric Drill
Notes to the Installer:
1) Read the entire installation instructions prior to beginning the installation
of this accessory.
2) Make sure the vehicle is completely clean before the accessory is installed.
3) Ensure the vehicle is properly protected in the area(s) that the accessory is to
be installed.
4) To prevent vehicle damage, never place tools on top of painted surfaces, seats,
dash pad, console or floor carpet/mats.
5) Always wear appropriate safety gear to include gloves and safety glasses when required.
Notes to the Customer:
1) This vehicle's Cargo Net is equipped with upper bungee hook clips to aid in the retention of items placed in the
Cargo Net.
2) It is recommended that when not using the Cargo Net to carry items, that the hook clips remain unfastened.
See step 2 on page 6 for details.
3) Contained are detailed instructions for the use of the hook clips. After installation of the Cargo Net, please place the
installation instructions in the vehicle glove compartment for later use if needed.
Denotes safety equipment required to be
used such as a mask, safety glasses, gloves,
and hearing protection.
Safety Glasses
Hearing Protection
Mask
Gloves
Denotes instructional steps
necessary to complete the
process.
Denotes quality processes to be
checked prior to moving to the next
step.
Denotes cautions to be taken to avoid
physical injury or electronic component
damage.
Denotes warnings that may lead to
serious physical injury or vehicle
damage.
Denotes specific tools that are
necessary to complete the step.
Denotes cautions to be taken to avoid
vehicle and component damage.
FMVSS 110
Compliance
Information
Part Number:
C2017 ADU01
C2017 ADUP1
0.364 lbs
0.165 kg
(Gross
Weight)
All dealers must determine if
the weight they have added in
the form of all options or
accessories, when added to
the weight of all Port/Dealer
Installed options or
accessories, exceeds the
lesser of 1.5% of GVWR or 100
lbs. If the additional weight
does exceed the lesser of the
indicated thresholds, a “Load
Carrying Capacity Reduced”
label must be installed. A
black, fine-point, indelible
marker must be used to write
by hand onto the label, the
reduced carrying capacity in
kilograms or pounds, which is
the total weight of all added
options and accessories.
Load Label Part Number:
NP070 - 09003
Cargo Nets are constructed of elastic and netting. Please use caution to avoid entanglement.
Avoid eye injury. DO NOT overstretch the Cargo Net, ALWAYS keep your face and body out of the
Cargo Net's recoil path.
5INS131600HI
Revision Date
06/17/2014
Page 1 of 7

2
2
2
Hardware Total
6
T-Anchors
Self-Tapping Screws
C
3
B
1
Installation Instructions
Hardware Overview
T-Anchors with Spigot
1
1
Cargo Net
A
2
1
Hardware Kit
No.
Qty.
Description
HYUNDAI Genuine Accessories
Kit Overview
1
2
3
5INS131600HI
Revision Date
06/17/2014
Page 2 of 7

HYUNDAI Genuine Accessories
1
Clip Removal Tool
2
Be careful not to damage the rubber seal when dislodging.
Do not allow the rubber seal gasket material to transfer to
the vehicle body.
DO NOT allow the clip removal tool to press against the
rubber seal.
Be careful not to damage the panel fasteners when
performing this step.
Store the plastic mounting clips in a safe location for later
installation.
N
O
T
E
1. Open the trunk lid.
2. Locate the rubber seal found alongside the vehicle body / trunk lid
opening.
3. Starting at the lower panel fastener as shown, carefully dislodge the
rubber seal up to the upper panel fastener.
4. Repeat for the opposite side.
N
O
T
E
1. Locate the driver side, lower panel fastener as shown.
2. Using a Clip Removal Tool, carefully remove the fastener.
3. Repeat for the opposite side.
Electric Drill, 1/4" (6mm) Drill Bit, and Drill Stop,
Deburring Tool, Masking Tape, Rust Inhibitor
(Primer), and Vacuum Cleaner
3
4
DO NOT oversize holes when performing this step.
N
O
T
E
1. Place a strip of Masking Tape below the lower hole, ensuring that the
adhesive side of the tape is exposed to catch metal debris during
drilling.
2. Using the 1/4" (6mm) Drill Bit equipped with a Drill Stop set to 7/16"
(10mm) depth, drill the lower hole location as shown in the drawing.
Press gently when drilling to reduce risk of the drill bit jamming.
3. Deburr the hole using a Deburring Tool.
4. Use a Vacuum Cleaner to remove any remaining debris.
5. Apply Rust Inhibitor (Primer) to the drilled hole.
6. Repeat for the opposite side.
N
O
T
E
1. Assemble a T-anchor to a self tapping screw.
2. By hand, insert the T-anchor assembly and align to a horizontal
position; tighten until snug and no gaps are found.
3. Repeat for the opposite side.
5INS131600HI
Revision Date
06/17/2014
Page 3 of 7

Ensure that the T-Anchor is fully seated to a vertical position.
Use caution when tightening the T-Anchor so you do not
damage the plastic panel.
N
O
T
E
1. By hand, insert the provided T-anchor with spigot; tighten until snug and
no gaps are found.
2. Align the T-anchor to a vertical position shown in the drawing.
3. Repeat for opposite side.
N
O
T
E
1. Check for movement or gaps between the T-Anchor and rear plastic
sill panel.
2. If movement or a gap exceeding 1.0mm is found, further tighten using
1/4 ~ 1/2 increment turns until the T-anchor is seated to a horizontal
position.
3. Repeat for opposite side.
7
8
Ensure that the T-Anchor assembly is fully seated to a
horizontal position.
Note: a <1.0mm gap will still exist because of the shoulder of
the self tapping screw.
N
O
T
E
1. Check for movement or gaps between the T-Anchor and trunk liner.
2. If movement or a gap exceeding 1.0mm is found, further tighten using
1/4 ~ 1/2 increment turns until the T-anchor is seated to a horizontal
position.
3. Reattach the rubber seal from step 1 by firmly pushing along the
entire edge to ensure it is correctly seated.
4. Repeat for the opposite side.
N
O
T
E
1. Locate the lower plastic grommet as shown. By hand, rotate the
grommet counter clockwise to remove, then discard the grommet.
2. Repeat for the opposite side.
HYUNDAI Genuine Accessories
5
6
5INS131600HI
Revision Date
06/17/2014
Page 4 of 7

N
O
T
E
1. Attach both lower bungee loops as shown.
N
O
T
E
1. Correctly installed cargo net.
11
12
N
O
T
E
1. Position the Cargo Net so the opening is in the upward position and the
pull tab logo is facing rearward.
N
O
T
E
1. Attach both upper bungee loops as shown.
HYUNDAI Genuine Accessories
9
10
5INS13160HI
Revision Date
06/17/2014
Page 5 of 7

Ensure bungee is fully seated in the hook clips.
N
O
T
E
1. Locate the three hook clips located along the top of the cargo net.
N
O
T
E
1. Grasp the bungee cord adjacent to the hook clip and wrap two or three
fingers around to hold it securely as shown.
2. With the same hand, use your index finger and thumb to hold the hook
clip.
3. Grasp the bungee cord with the other hand and slide the cord to fasten
it to the clip. To unfasten, pull the bungee cord out of the clip.
HYUNDAI Genuine Accessories
Use of Cargo Net Hooks
1
2
5INS131600HI
Revision Date
06/17/2014
Page 6 of 7

HYUNDAI Genuine Accessories
Visual Check
Items To Be Checked
Results Of The Check
Cargo Net pull tab location.
The pull tab logo is facing rearward.
Ensure the four T-Anchors are tight and in the correct
orientation.
T-Anchors are tight and in the correct oriention.
Ensure bungee loops are secured to all four T-
Anchors.
Bungee loops are secured to all four T-Anchors.
5INS131600HI
Revision Date
06/17/2014
Page 7 of 7