Hyundai HYUGL002 User manual

For inquiries please contact: Licensed by HYUNDAI Corporation Holdings, Korea
E-mail: [e-mail] Imported/Distributed by Azoogi Pty Ltd
www.hyundailighting.com.au
Smart Colour changing garden
lights kit
Installation Manual
RGBW

For inquiries please contact: Licensed by HYUNDAI Corporation Holdings, Korea
E-mail: [e-mail] Imported/Distributed by Azoogi Pty Ltd
www.hyundailighting.com.au
Product Specification
Product code
HYUGL002
Weight
3 kg
CCT
RGB + 2700K
Lumen Output
350lm
Finish
Black
Input Voltage (Garden Light)
12V DC
Input Voltage (LED Driver)
240V AC
Wattage
5W x 5
IP Rating
IP67
Warranty
3 Years
CRI
> 80
Cable
10m (2m between spikes)
Lamp dimensions
𝜙6cm x 24cm height
Beam Angle
60°
Control range
10m
Warranty information
3 years limited warranty. Visit https://hyundailighting.com.au/terms-and-conditions/ for detailed
warranty information.
Email: [e-mail]
Packaging contents
a. 5 x garden lights with male connectors
b. 1 x 10m connection cable with female T-connectors.
c. 5 x garden light spikes
d. 1 x LED driver
e. 5 x (washers + screws)
f. 4 x screws
g. 1 x allen key
h. 2 x connector plugs
i. Smart Bluetooth controller

For inquiries please contact: Licensed by HYUNDAI Corporation Holdings, Korea
E-mail: [e-mail] Imported/Distributed by Azoogi Pty Ltd
www.hyundailighting.com.au
Installation Steps
1. Before installation, make sure the power supply is switched off.
2. Attach the spike to the light via the screw provided.
3. Adjust the orientation of the garden light to the desired angle and tighten the screw.
4. Spread the connection cable in your garden placing the cable end with the male connector near the
power point.
5. Connect the garden lights to the cable via the provided connections. Make sure you align the notch
in the connectors before connecting them. Tighten the
connector cap to seal the connection and stake the light into the ground.
6. Connect the LED driver to the input cable of the smart controller and connect the output cable of
the smart controller to the garden light cable
7. If not all garden lights are used, seal the open connectors using the connector plugs provided.
8. Connect the 3-pin plug of the driver to the AC mains socket and switch the power supply on.
Note:
1. Make sure the LED driver, the smart controller and the garden light are not sited such that they get
flooded with water.
2. Ensure all connections are tight and sealed by tightening the connector cap.
3. Do not leave any connector open.
Wiring
Refer to the wiring diagram below for wiring illustrations.
2.5m
1m
1m
1.5m

For inquiries please contact: Licensed by HYUNDAI Corporation Holdings, Korea
E-mail: [e-mail] Imported/Distributed by Azoogi Pty Ltd
www.hyundailighting.com.au
Download App
Download “Smart Life – Smart Living” app from Apple store or Google Play and install it into your smart
phone or tablet device. Alternatively, scanning the QR code below will take you to the app’s download
page.
Registration and Login
1. Open the “Smart Life – Smart Control” app from your smart phone.
2. Follow the prompts to register and login
Add device
1. Connect the RGBW Garden Light LED driver to a power source. Once connected, the lights will start
blinking rapidly cycling through red, blue, and green colours. To enter pairing mode, connect and
disconnect the connector between the smart controller and the LED driver 3 to 5 times. Finally, the
connector must be in connected state. The lights should now be only RED in colour indicating it has
entered pairing mode.
2. Turn on the Bluetooth in your smart phone or tablet.
3. In the Smart Life app, press the (+) symbol on the top right-hand corner. When device window pops
up with the light to add, press “Go to add”.
4. Pairing process will begin. Do not turn off the strip while pairing and wait for the pairing process to
complete. If you get a message that says - “Failed to Add”, repeat the steps from 1 to 3 to pair the
device.
5. Once the device has been successfully added, you can begin using it.
Cleaning
Before cleaning, disconnect from mains supply and allow the garden light to cool. Only use a damp,
microfibre cloth for cleaning. A diluted solution of a mild pH-neutral liquid detergent can be used for
resistant dirt. Do not use high pressure cleaners.
The RCM marking of this product applies to AS/NZS CISPR15 (EMC) “Limits and methods of
measurement of radio disturbance characteristics of electrical lighting and similar equipment”. This
product is designed to conform to AS/NZS60598 “Luminaires, general requirements and tests”.