Hyundai J0F73 AU000 User manual

Genuine Accessories
Glasses Gloves
Mask Hearing Protection
Part Weight (Gross) FMVSS 110 Compliance Information
1) Read the entire Installation Instructions prior to beginning the installation of the part.
2)
3) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
4) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
5) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
6) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
No.
1
2
0.70
lbs All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load
Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying
capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
0.32
kg
2 2 Self-Adhesive Loop-End Fastener Strips
Basic Required Tools
Instructional Symbols / Definitions
Denotes quality processes to be checked
prior to moving to the next step
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a
replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old
registration cannot be reused.
Language English
4/2/2020Rev. Date
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
( A )
First Aid Kit
Part No.
Model Year
J0F73 AU000
Note:
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
Denotes warnings that may lead to serious
physical injury or vehicle damage
Multiple
Accessory:MultipleVehicle Model:
Difficulty:
(C) Master Technician or Specialist
(B) Dealer Technician
Denotes specific tools that are necessary
to complete a step
Denotes cautions to be taken to avoid
vehicle and component damage
Qty
1 Hyundai First Aid Kit
Description
N
O
T
E
Denotes important information to be
reviewed during the step
None
Notes to the installer:
Kit Overview
(A) Customer
12
(2)Self‐adhesive
Loop‐endFastener
150580B
Revision Date
4/02/2020 Page 1 of 2

Genuine Accessories
Cleaning Instructions for:
• Install first aid kit per instructions to avoid sliding and shifting.
• Fasteners are intended to prevent sliding and shifting only; they will not retain kit in the event of sudden stop or
collision.
• In a sudden stop or collision unsecured cargo could cause serious personal injury.
N
O
T
E
1
A. Install the Hyundai First Aid Kit in one of the following manners:
• Place First Aid Kit in an enclosed compartment.(i.e. spare tire well, sub-floor storage compartment, glove compartment, cargo net, etc.)
• Place First Aid Kit on a carpeted surface.
a. Detach self-adhesive loop-end fastener strips; retain these for future use.
b. Press First Aid Kit firmly to carpet to secure hook-end fastener strips.
• Place First Aid Kit on a non-carpeted surface using the self-adhesive loop-end fastener strips.
a. Thoroughly clean the non-carpeted surface with isopropyl alcohol.
b. Allow surface to dry completely before attaching fastener strips.
c. Ensure the self-adhesive loop-end fasteners are attached to the hook-end fasteners on back of First Aid Kit. Remove the paper lining from the loop-end
fastener strips.
d. Press the First Aid Kit against a non-carpeted surface to adhere strips.
Use care when handling and placing the First Aid Kit to avoid contact with any
dirt.
No dirt or fingerprints on the First Aid Kit.
The First Aid Kit should be in a secured position with the Hyundai logo facing the
Installer.
Confirm proper placement of the First Aid Kit.
Item to be Checked Result
Care & Cleaning
Spot clean with a damp cloth as needed (do not use chemical based cleaners).
First Aid KitMultiple
Visual Check
150580B
Revision Date
4/02/2020 Page 2 of 2