Hyundai HYW130DC User manual
PETROL GENERATOR
HYW130DC
Instruction Manual
1. Safety Instruction
1.12 Refrain from using the air compressor when
welding. Also, it is recommended that you disconnect all
sources from the generator as well when welding.
1.13 Welding power source used for pipeline defrost
operation is prohibited.
3.Machine structure
1 2 3
5
4
18
6
1
7
1414
8
11
9
12
10
15 1317 16
Notice: Any modification on the control panel and
appearance will not be advised again.
1. Starting lock 2. Three-phase circuit 3. 3 in 1 digit meter
4. Power supply switch 5.Current indicator 6.Thrust regulator
7. Negative welding socket 8．Power indicator 9.Over-heated
indicator 10. Current regulator 11. Positive welding socket
12.Three-phase terminals 13. Grounding bolt 14. Alternator assy.
15. Control panel and labels 16. Oil alert lamp 17. Battery
18. Control box
1. Engine assy. 2. Frame beam 3. Fuel tank 4. Fuel tank cover
5. Plastic cover 6. Frame 7. Handle 8. Handle sheath 9. Muffler
6
7
8 1
1
5 4 3
2
1
1．Throttle 2．Air cleaner 3．Recoil starter and handle
4．Recharge module 5．Fuel switch 6．Side board
1 2 3 4 5
6
4.Preparation
�
box, remove the air filter cover. being careful not to
damage the air filter cover.
4.6.3 Remove filter element from the air filter cover.
4.6.4 Checking if air filter is clean and in good condition.
If air filter is dirty, wash it. If the air filter is damaged, it
must be replaced.
4.6.5 Reload filter element on the bottom cover of air
filter.
4.6.6 Remount air filter cover, observeprotective cover,
and confirm air filter locked. Make sure there is no gap
between upper cover and bottom cover. In the absence
of air filter element or filter element were damaged, dust
will enter into engine, causing rapid engine wear.
4. 7 please Check The Battery Voltage Between 11.5-
12.5 When Starting The Cmachine.
5.Starting
Notice:
6. Running
Notice:
(A)
�s.o
6.7 Attention: The machine can work under two types of power,
generator and commercial power.
6.7.1 If choose generator to supply welding, operator needs to
start the generator first. Then turn Power Supply Switch to
“GENERATING” position. Next turn “GENERATING” circuit to “ON”
position. When the working light on the control panel “ ”is on,
regulate the current and thrust rotary switch to appropriate
position and start welding.
6.7.2 If choose commercial power to supply welding, operator
MUST make sure the machine is completely stopped. Then
connect the plug with power source and turn Power Supply Switch
to “ELECTRICITY” position. Next turn “ELECTRICITY” circuit to
“ON” position. When the working light on the control panel “ ”is
on, regulate the current and thrust rotary switch to appropriate
position and start welding.
◆When using generator function, operator needs to cut off power
circuit first. Let machine running for 3 minutes with non-load. Then
turn off the power switch to “OFF” position.
◆When using welding function, operator needs to stop welding
first. Then turn Power Supply Switch to middle position. Cut off all
circuit on the control panel. Let machine running for 3 minutes with
non-load. Then turn off the power switch to “OFF” position.
Table of contents
Other Hyundai Portable Generator manuals
Hyundai
Hyundai HY1000SI User manual
Hyundai
Hyundai HY1000SI User manual
Hyundai
Hyundai HY3500Ei User manual
Hyundai
Hyundai HY1000SI User manual
Hyundai
Hyundai HY2200RV User manual
Hyundai
Hyundai FULLPOWER 65213 User manual
Hyundai
Hyundai DHY6000LE User manual
Hyundai
Hyundai HHD1250 User manual
Hyundai
Hyundai HPS-300 User manual
Hyundai
Hyundai HY3800LE-LPG User manual
Hyundai
Hyundai DHY8500SE User manual
Hyundai
Hyundai HG3300I-A User manual
Hyundai
Hyundai HPS-300 User manual
Hyundai
Hyundai HY3800RV User manual
Hyundai
Hyundai DHY6000SE User manual
Hyundai
Hyundai HCP9000 User manual
Hyundai
Hyundai STG1000 User manual
Hyundai
Hyundai DHY14KSE User manual
Hyundai
Hyundai DHY2500L/E User manual
Hyundai
Hyundai HY2200P User manual
