IBM NetVista Owner's manual

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 1of 35
IBM NetVista
Type: 6049 and 2259
Hardware
Maintenance
Manual
Version: HMM02

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 2of 35
Safety information
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
• Do not connect or disconnect any cables or perform installation, maintenance, or
reconfiguration of this product during an electrical storm.
• Connect all power cords to a properly wired and grounded electrical outlet.
• Connect to properly wired outlets any equipment that will be attachedto this
product.
• When possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or
structural damage.
• Disconnect the attached power cords, telecommunications systems, networks, and
modems before you open the device covers, unless instructed otherwise in the
installation and configuration procedures.
• Connect and disconnect cables as described in the following table when installing,
moving, or opening covers on this product or attached devices.
To connect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to
connectors.
4. Attach power cords to outlet.
5. Turn device ON.
To disconnect:
1. Turn everything OFF.
2. First, remove power cords from
outlet.
3. Remove signal cables from
connectors.
4. Remove all cables from devices.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 3of 35
Lithiumbatterynotice
CAUTION:
Danger of explosion if battery is incorrectly replaced.
When replacing the battery, use only IBM Part Number 33F8354 or an equivalent
type battery recommended by the manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
• Throw or immerse into water
• Heat to more than 100°C (212°F)
• Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Modem safety information
To reduce the risk of fire, electrical shock, or injury when using telephone equipment,
always follow basic safety precautions, such as:
• Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
• Never touch un-insulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
Laser compliance statement
Some IBM Personal Computer models are equipped from the factory with a CD-ROM
drive or a DVD-ROM drive. CD-ROM drives and DVD-ROM drives are also sold
separately as options. CD-ROM drives and DVD-ROM drives are laser products.
These drives are certified in the U.S. to conform to the requirements of the
Department of Health and Human Services 21 Code of Federal Regulations (DHHS
21 CFR) Subchapter J for Class 1 laser products. Elsewhere, these drives are certified
to conform to the requirements of the International Electrotechnical Commission
(IEC) 825 and CENELEC EN 60 825 for Class 1 laser products. When a CD-ROM
drive or a DVD-ROM drive is installed, note the following handling instructions.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 4of 35
CAUTION:
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
Removing the covers of the CD-ROM drive or DVD-ROM drive could result in
exposure to hazardous laser radiation. There are no serviceable parts inside the
CD-ROM drive or DVD-ROM drive. Do not remove the drive covers.
Some CD-ROM drives and DVD-ROM drives contain an embedded Class 3A or
Class 3B laser diode. Note the following statement.
DANGER
Laser radiation when open. Do not stare into the beam, do not view directly with
optical instruments, and avoid direct exposure to the beam.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 5of 35
Getting Started
1.Before you begin, have a Philips
medium sized head screwdriver to begin.
2.Locate the 3 screws at the back of the
case; use the screwdriver to loosen them.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 6of 35
3
.Using both hands, gently pull back the
top cover as shown in the figure. Slide
the cover up off the frame of the case.
4. For installing the mainboard, locate
the three screws which secure the plate
and remove it.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 7of 35
Installing the Power Supply Fan
1.The power supply should be installed
in the back of the chassis. This is to draw
the air out of the inside of the case.
Check the position of the power supply
fan as shown in the figure.
2.Using the screwdriver, gently tighten
the three screws.
This completes the installation for the
power supply fan.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 8of 35
Assembling the Mainboard
1.The plastic spacers provide extreme
support in areas of high mechanical stress
on your mainboard. Insert the plastic
spacers in the 2 mounting holes as shown
in the figure through the back of your
mainboard. The plastic spacers are
provided with the case.
2
. Position the mainboard in the plate so
you can see the alignment of the
mounting holes in the mainboard with the
standoff holes. There are at least 4 screws
that need to be secured.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 9of 35
3.Prepare the CPU, heatsink and the
CPU cooling fan.
4Pull the CPU socket-locking lever
away from the socket to unhook it and
raise the locking lever to the upright
position. Place the CPU into the socket
and pull down the lever. Apply thermal
grease to the top of the CPU.
5.Place the heatsink at the top of the
CPU. See figure for reference.
478Pins ?
Pentium 4
CPU

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 10 of 35
6. Attach the CPU cooling fan on top of
the heatsink. Snap the four retention legs
of the cooling fan into place.
7.Lock both levers on top of the
cooling fan to their opposite sides to
secure the cooling fan on top of the
heatsink.
8.Connect the CPU cooling fan power
cable to the CPU fan connector.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 11 of 35
Installing the Memory Modules
9.Open the left and right levers of the
slot. Then firmly slide the Memory
Module into the DIMM slot. The DIMM
slots are keyed with notches and the
DIMMs are indicated with cut outs so
that they can only be installed correctly.
10.After installing, the Memory
Module should look like this.
11.To install the mainboard inside the
case. Locate the three mounting brackets
on the case as shown in the figure.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 12 of 35
12.Place the mainboard over the
mounting brackets. Then slide the
mainboard into place as shown in the
next figure.
13.Secure the mainboard into the
mounting brackets with screws. Do not
overtighten the screws. Gentle pressure is
enough.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 13 of 35
Connecting the Power Supply
1.After you have installed the
mainboard into the case, you should
connect the power cable from the case
power supply unit to the mainboard
power connector. Since the floppy drive
is situated closely to the power supply.
For convenience purpose, loosen the
screw that holds the Floppy drive.
2.Push the storage bay sideways as
shown in the figure.
3. Locate the mainboard power
connector. See figure for reference.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 14 of 35
4. The power connector should fit
perfectly in the slot on the mainboard.
Note the orientation of the cables before
trying to connect them. Each function of
the cable is already defined.
5. Connect the +12V power connector.
Make sure the power connectors are
properly seated and firmly attached.
6.Push back the storage bay to its
original position. There are two things
that need to be aware of: One is to make
sure that the screw holes of the mounting
box are aligned with that of the drive and
the brackets are smoothly attached to the
hook.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 15 of 35
7. The storage bay should slide easily
back to place.
8. Secure the chassis and the storage
bay with screws. Do not over tighten the
screws. Gentle pressure is enough.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 16 of 35
Installing the CD-ROM, Floppy
and Hard Drives
1. There are two different size "bays"
into which each of the various drives will
fit. Take a close look at the drive and
determine which is the “bay” for the
floppy drive. Install the floppy drive into
the upper side of the storage bay. See
figure for reference.
2.Slide the drive in the appropriate
location. For a 3.5” drive, secure the two
screws located on the both side of the
storage bay.
You can easily see where the screw holes
in the drive line up.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 17 of 35
3.For the hard disk drive, follow the
same manner for installing the floppy
disk drive.
Always secure the screw
s when installing
the drives. This will prevent them from
moving and falling from the storage bay.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 18 of 35
4.For the CD-ROM drive, gently open
the door panel.
5. Slide the CD-ROM
drive into the bay
and align the drive's faceplate with the
front of the case.
6. When the CD-ROM drive is
positioned correctly, secure the drive to
the bay using four screws.
The figure shows the other side of the
chassis.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 19 of 35
7.Close the door panel. This completes
the setup for the CD-ROM drive.
8.Nex
t, you should get familiar with the
cables that are used with the various
drives. The first cable is use for the
floppy drives, the second cable is for the
hard disk drive and the third long cable is
use for the CD-ROM drive.
For the power cables, the cable has
peripheral and floppy drive power
connector and is designed to connect
from the power supply to the drives.
9.Plug the CD-ROM cable into the
Primary IDE channel on the mainboard.
The edge of the cable that is red
determines its orientation. Push the
CD-ROM cable squarely onto the
Primary pins.

IBM NetVista Type 6049 and 2259 Refresh 1.1
Version: HMM02 20 of 35
10.Connect the other end of the cable
to the CD-ROM drive. Note the
orientation of the cable before trying to
connect it.
11. Next, plug the hard disk cable into
the Secondary IDE channel on the
mainboard. The edge of the cable that is
red determines its orientation. Push the
hard disk cable squarely onto the
Secondary pins.
12.Following the same procedure
mentioned in step 10. Connect the other
end of the cable to the hard disk drive.